Inhaltszusammenfassung zur Seite Nr. 1
14" SVGA Color Monitor
TC-1428
Inhaltszusammenfassung zur Seite Nr. 2
Customer’s Record The serial number of this product appears on the back of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid in identification in the event of theft or loss. Model number: TC-1428 Serial number: WARNING: To reduce the risk of fire or electric shock, do not expose this Computer Display to rain or moisture. I T U A C The power cord is intended to serve as the main disconnect device. Insta
Inhaltszusammenfassung zur Seite Nr. 3
2. The monitor will be automatically recovered to the on state by receiving normal sync. signals from PC. 3. The power management states are identified below: Power Mgmt. States H-Sync. V-Sync. LED Color On ON ON Green OFF ON Light Amber Power ON Suspend ON OFF Light Amber Off OFF OFF Dark Amber Power OFF OFF OFF Off Table of Contents 1 . . 3 2 . Precaution s . 3 . 4 3 . Feature s s 5 5.Contro l Location s an d Adjustment s . . 7 s . 9 7. Pi n Assignments. . 0 1 8.Timin g . 11 9.Troubleshooti
Inhaltszusammenfassung zur Seite Nr. 4
Congratulations on your purchase of a NEW ULTRA VGA monitor. One of the most versatile monitors available today, the TC-1428 automatically adjusts its vertical and horizontal scanning frequencies to those of your computer’s graphics adapter or video chip sets. The TC-1428 crisp text and vivid color graphic displays when used with NEW ULTRA VGA compatible graphics adapters (see specifications). 2. Precautions 1. To prevent electric shock, do not remove screws or cover. There are no user-servicea
Inhaltszusammenfassung zur Seite Nr. 5
4. Do not put the monitor or other heavy objects on the power supply cord. A damaged power cord may cause fire or electric shock. 5. Do not insert sharp objects into the monitor. They may cause fire or 6. Do not allow liquids to spill into the cabinet. 7. To reduce eye fatigue, avoid using the display in direct sunlight or under 8. Do not operate the monitor beyond the specified temperature and humidity range (see specifications on page 5). 9. For proper operation, keep the monitor adequately ve
Inhaltszusammenfassung zur Seite Nr. 6
4. Specifications Power Source: AC 90~264V, 50/60Hz Power Consumption: 75W Maximum Power Management: VESA DPMS (<5W) 14 inches, 90° deflection, 0.28mm dot pitch Picture Tube: Viewable size 13.1 inches. Resolutions l Horizontal: 1024 pixels (interlaced) * Vertical: 768 lines (interlaced) * Video: Analog 0.7 Vp-p / 75 ohm Positive * Separate Sync: TTL Level . . . . . . . . . . . . . . . Positive/Negative * Horizontal: 31.5KHz/35KHz/38KHz * Vertical: 50Hz~100Hz continuous Display Colors * ANALOG In
Inhaltszusammenfassung zur Seite Nr. 7
Low Radiation: * X-ray radiation: < 100n Gylh * Magnetic field: Band I (5KHz-2KHz): < 250nT. Band II (2KHz-400KHz): < 25nT. Tilt and Swivel Operation: The swivel range is normally limited to a range of 45 degrees to the right or left of the front position (marked by a small molded pip on the top front bottom of the base). The tilt range is normally limited at an angle of -5 degrees forwards and + 15 degrees backwards. This allows you to set the screen angle to the viewing position most comfortab
Inhaltszusammenfassung zur Seite Nr. 8
5. Control Locations and Adjustments Note: The numbers indicate the control item whose description is found on the following page. -7-
Inhaltszusammenfassung zur Seite Nr. 9
Push to turn the display on, and push again to turn off. The power indicator will light when the display is on. 2. BRIGHTNESS Control Adjusts the display to the desired brightness level. (factory preset at the center detent of the control knob) 3. CONTRAST Control Adjusts the display to the desired contrast 4. H. WIDTH Control Adjusts the display to the desired horizontal width. (factory preset at the center detent of the control knob) 5. H. POSITION Control Adjusts the display to the desired ho
Inhaltszusammenfassung zur Seite Nr. 10
6. Connections Your monitor has two connecting cables: a Power Supply Cord, which connects to a wall outlet, surge protector or other power source, and a Signal Cable, which connects to the graphics adapter of your computer. To insure safety and correct operation, always follow these four steps when connecting the monitor: 1. Disconnect the power supply cords from your computer and monitor. 2. Connect the signal cable from the monitor to the graphics adapter of your computer. The connector is sh
Inhaltszusammenfassung zur Seite Nr. 11
7. Pin Assignments The pin assignment of the video signal cable are shown below: 15-Pin Mini D-Sub Male Connector PIN NO. 1 RED 2 GREEN 3 BLUE 4 GROUND or OPEN FOR DDC 5 GROUND 6 R-GROUND G-GROUND 7 8 B-GROUND NO CONNECTION 9 10 GROUND or OPEN FOR DDC 11 GROUND 12 NO CONNECTION or DDC SDA 13 H. SYNC. 14 15 NO CONNECTION or DDC SCL -10- V. SYNC. SIGNAL
Inhaltszusammenfassung zur Seite Nr. 12
8. Timing Charts SEPARATE SYNC. HORIZONTAL VERTICAL Sync. Polarity: Positive/Negative PRESET TIMING-VGA/SVGA VGA SVGA Fh (KHz) A µs (Line time total) 3.813 C µs (Back porch) D µs (Active) 0.636 0.636 0.636 0.667 Fv (Hz) 0.063 0.063 0.064 0.057 0.106 0.626 11.111 0.381 T ms (Front porch) Sync. Sync. Sync. Sync. V. Sync. Polarity No No No No No -11- Positive Negative Negative Positive Negative Positive Negative Negative Negative Positive H. Sync. Polarity Sync. Separate Separate Separate Separate
Inhaltszusammenfassung zur Seite Nr. 13
PRESET TIMING-8514A/VESA VGA/UVGA 8514/A UVGA VESA VGA 1024x768 640x480 540x480 800x600 800x600 1024x768 Fh (KHz) 35.520 37.500 37.860 46.875 48.077 48.363 A µs (Line time total) 28.153 26.667 26.413 21.333 20.800 20.677 B µs (Synch. pluse) 3.919 2.032 1.270 1.616 2.400 2.092 1.247 4.064 C µs (Back porch) 3.810 3.232 1.280 2.462 20.317 D µs (Active) 22.810 20.317 16.162 16.000 15.754 E µs (Front porch) 0.178 0.508 0.762 0.323 1.120 0.369 Fv(Hz) 86.960 75.000 72.809 75.000 72.187 60.000 11.500 13
Inhaltszusammenfassung zur Seite Nr. 14
9. Troubleshooting Before you call an authorized service center, please check if the following items are properly connected or not. If a non-IBM personal computer or graphics adaptor is being used, make sure the pin assignments of signal input connector and the signal timing meet the specifications inducated above. CHECKS PROBLEM Rear * AC Cord plugged in No Picture or Front * POWER Switch on POWER Indicator off. Rear * Signal Cable connected * Turn off POWER switch, wait No Picture, POWER Indic
Inhaltszusammenfassung zur Seite Nr. 15
Federal Communications Commission Requirements Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, of not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Inhaltszusammenfassung zur Seite Nr. 16
P/N:5035111312
