Resumen del contenido incluido en la página 1
Instruction Manual
FRENIC 5000G11S/P11S
High-Performance, Low-Noise Inverter
General-Purpose Industrial Machines Fans and Pumps
230V Series 230V Series
0.25HP/FRNF25G11S-2UX 7.5HP/FRN007P11S-2UX
to 125HP/FRN125G11S-2UX to 150HP/FRN150P11S-2UX
460V Series 460V Series
0.50HP/FRNF50G11S-4UX 7.5HP/FRN007P11S-4UX
to 600HP/FRN600G11S-4UX to 800HP/FRN800P11S-4UX
！
CAUTION
Read all operating instructions before
installing, connecting (wiring),
operatin
Resumen del contenido incluido en la página 2
Preface Thank you four purchasing our FRENIC5000G11S or FRENIC5000P11S series inverter. This product is used to drive a 3-phase electric motor at variable speed. As incorrect use of this product may result in personal injury and/or property damage, read all operating instructions before using. As this manual does not cover the use of option cards, etc., refer to relevant manuals for option operations. Safety Instructions Read this manual carefully before installing, connecting (wiring)
Resumen del contenido incluido en la página 3
Instructions on wiring WARNING • Connect the inverter to power via a line-protection molded-case circuit breaker or Fuse, as fire may result. • Always connect a ground wire, as electric shock or fire may result. • A licensed specialist must perform the wiring works, as electric shock may result. • Turn off the power before starting the wiring work, as electric shock may result. • Wire the inverter after installation is complete, as electric shock or injury may occur. CAUTION • Con
Resumen del contenido incluido en la página 4
Instructions on maintenance, inspection, and replacement WARNING • Wait a minimum of five minutes (30HP or less) or ten minutes (40HP or more) after power has been tumed off (open) before starting inspection. (Also confirm that the charge lamp is off and that DC voltage between terminals P (+) and N (-) do not exceed 25V.) Electrical shock may result. • Only authorized personnel should perform maintenance, inspection, and replacement operations.(Take off metal jewelry such as watches an
Resumen del contenido incluido en la página 5
Conformity to Low Voltage Directive in Europe CAUTION Table 1-1 Applicable equipment and wire size for main circuit in Europe Fuse/MCCB 2 Tightening torque [N*m] Recommended wire size [mm ] current rating [A] L1/R, L2/S, L3/T Inverter type With Without ( G) G DCR DCR With Without DCR DCR 1/4 FRNF25G11S-2UX 5 5 1/2 FRNF50G11S-2UX 5 5 1.2 - - 2.5 1 FRN001G11S-2UX 5 10 2.5 (2.5) 2.5 2.5 (2.5) 2 FRN002G11S-2UX 10 15 3 FRN003G11S-2UX 10 15 1.8 5 FRN005G11S-2UX 20 30 4(4) 7.5 F
Resumen del contenido incluido en la página 6
Conformity to Low Voltage Directive in Europe CAUTION Table 1-2 Applicable equipment and wire size for main circuit in Europe Fuse/MCCB 2 Tightening torque [N*m] Recommended wire size [mm ] current rating [A] L1/R, L2/S, L3/T Inverter type With Without ( G) G DCR DCR With Without DCR DCR 1/2 FRNF50G11S-4UX 5 5 1.2 - - 1 FRN001G11S-4UX 5 5 2 FRN002G11S-4UX 5 10 2.5 3 FRN003G11S-4UX 10 15 1.8 (2.5) 2.5 5 FRN005G11S-4UX 10 15 2.5 2.5 (2.5) 7.5 FRN007P11S-4UX 15 20 7.5 FRN0
Resumen del contenido incluido en la página 7
Compliance with UL/cUL standards [Applicable to products with UL/cUL mark] CAUTION Tightening torque and wire range 2 . Inverter type Wire range [AWG] (mm ) Required torque [lb-inch](N m) Auxiliary Auxiliary Voltage Main L1/R,L2/S,L3/T G11S/P11S control- Control control- Control terminal U,V,W power power FRNF25G11S-2UX FRNF50G11S-2UX 10.6(1.2) ― ― 16 (1.3) FRN001G11S-2UX FRN002G11S-2UX 15.9(1.8) FRN003G11S-2UX 14 (2.1) FRN005G11S-2UX 10 (5.3) FRN007G11S-2UX 8 (8.4) FRN007,010P1
Resumen del contenido incluido en la página 8
Compliance with UL/cUL standards [Applicable to products with UL/cUL mark] CAUTION • [CAUTION] Hazard of electrical shock. Disconnect incoming power before working on this control. • [CAUTION] Dangerous voltage exists until charge lights is off. • [WARNING] • More than one live parts inside the inverter. • Type1 “INDOOR USE ONLY” The inverter is approved as a part used inside a panel. Install it inside a panel. • Suitable for use on a circuit capable of delivering not more than 100,0
Resumen del contenido incluido en la página 9
Contents ･･･････････････ ････････････････････････ 1. Before Using This Product 1-1 5. Function Select 5-1 1-1 Receiving Inspections ････････････････1-1 5-1 Function select list ･･･････････････････ 5-1 ････････････････････････ 1-2 Appearance 1-1 5-2 Function Explanation ････････････････ 5-7 1-3 Handling the Product ･････････････････1-2 1-4 Carrying ････････････････････････････1-3 6. Protective Operation ････････････････････ 6-1 1-5 Storage ････････････････････････････1-3 6-1 List of Prot
Resumen del contenido incluido en la página 10
1. Before Using This Product 1-1 Receiving Inspections Unpack and check the product as explained below. If you have any questions about the product, contact the nearest Fuji sales office or your local distributor where you purchased the unit. ① Check the ratings nameplate to confirm that the delivered product is the ordered one. Ratings nameplate TYPE : Inverter type FRN 030 G11S-4 UX Power supply voltage system :2→ 230V grade、4→460V grade Se
Resumen del contenido incluido en la página 11
1-3 Handling the Product (1) Removing the surface cover For the inverter of 30HP or less, loosen the mounting screws of the surface cover, then remove the cover by pulling the top (see Figure 1.3.1). Fig. 1-3-1 Removing the surface cover (for inverter of 30HP or less) For the inverter of 40HP or more, remove the six mounting screws of the surface cover, then remove the surface cover. Fig. 1-3-2 Removing the surface cover (for inverter of 40HP or more) (2) Removing the keypad panel
Resumen del contenido incluido en la página 12
1-4 Carrying Carry the product by the main unit. Do not carry the product while holding the cover or parts other than the main unit. Use a crane or hoist to carry a product equipped with hanging holes. 1-5 Storage Temporary storage Temporary storage of this product must meet those conditions listed in Table 1-5-1. Table 1-5-1 Storage environment Item Specifications Ambient -10℃(14ºF) to +50℃(122ºF) temperature Storage Condensation or freezing must not occur as a result of -25℃(-13ºF)
Resumen del contenido incluido en la página 13
2. Installation and Connection 2-1 Operating Environment Install this product in a location that meets those conditions listed in Table 2-1-1 Table 2-1-1 Operating environment Table 2-1-2 Output current reduction rate Item Specifications based on altitude Location Indoor Altitude Output current reduction rate -10℃(14ºF) to +50℃(122ºF)(For products of Ambient 30HP or less, the ventilating covers must be 3300ft (1000m) or lower 1.00 temperature 3300-4950ft (1000 to 1500m) 0.97 removed
Resumen del contenido incluido en la página 14
An inverter of 40HP or more can be converted to an external cooling type simply by moving upper and lower mounting brackets as shown in Fig. 2-2-3. Remove the M6 bracket screws, move the brackets, then secure the brackets using the M5 case mounting screws. (The bracket screws are no longer required after changing the bracket mounting position.) Quantity of mounting screw Voltage Case mounting Inverter type Bracket screws series screws FRN040G11S-2UX to FRN100G11S-2UX 5 5 FRN040P11S
Resumen del contenido incluido en la página 15
2-3 Connection Remove the surface cover before connecting the terminal blocks as follows. 2-3-1 Basic connection ①Always connect power to the L1/R, L2/S, and L3/T main circuit power terminals of the inverter. Connecting power to another terminal will damage the inverter. Check that the power voltage is within the maximum allowable voltage marked on the nameplate, etc. ②Always ground the ground terminal to prevent disasters such as fire or electric shock and to minimize noise. ③Use
Resumen del contenido incluido en la página 16
Basic Connection Diagram (Sink Logic) G11S:15HP and above G11S:Up to 10HP P11S:20HP and above P11S:Up to 15HP DB) (CM) (THR) Ground-fault circuit interrupter (GFCI) RS-485 Fig.2-3-1 Note: The control circuit common terminals [11], (CM) and are isolated (*1) Use a drive with rated voltage matching the power supply voltage. (*2) Use as required. (*3) Use this peripheral device when necessary. (*4) Remove the jumper wire (*4) between P1 and P(+) before connecting a DC R
Resumen del contenido incluido en la página 17
Basic Connection Diagram to PLC (Sink Logic) G11S:15HP and above G11S:Up to 10HP P11S:20HP and above P11S:Up to 15HP Ground-fault circuit interrupter (GFCI) RS-485 Fig.2-3-2 2-5
Resumen del contenido incluido en la página 18
Basic Connection Diagram (Source Logic, Typically used in Europe) G11S:15HP and above G11S:Up to 10HP P11S:20HP and above P11S:Up to 15HP Ground-fault circuit interrupter (GFCI) RS-485 Fig.2-3-3 Note: The control circuit common terminals [11], (CM) and are isolated (*1) Use a drive with rated voltage matching the power supply voltage. (*2) Use as required. (*3) Use this peripheral device when necessary. (*4) Remove the jumper wire (*4) between P1 and P(+) before connectin
Resumen del contenido incluido en la página 19
Basic Connection Diagram to PLC (Source logic, Typically used in Europe) G11S:Up to 10HP G11S:15HP and above P11S:Up to 15HP P11S:20HP and above (THR) (P24) Ground-fault circuit interrupter (GFCI) RS-485 Fig.2-3-4 2-7
Resumen del contenido incluido en la página 20
2-3-2 Connecting the main circuit and ground terminals Table 2-3-1 Functions of main circuit terminals and ground terminals Symbol Terminal name Description L1/R, L2/S, L3/T Main circuit power terminal Connects a 3-phase power supply. U, V, W Inverter output terminal Connects a 3-phase motor. Connects a backup AC power supply to the Auxiliary control-power R0, T0 control circuit. (Not supported for inverter of 1HP input terminal or less) DC reactor connecting Connects the optional p
