Manual de instrucciones de GE NVI 800

Resumen del contenido incluido en la página 1

Resumen del contenido incluido en la página 2

Resumen del contenido incluido en la página 3

Resumen del contenido incluido en la página 4

Resumen del contenido incluido en la página 5

Resumen del contenido incluido en la página 6

Resumen del contenido incluido en la página 7

Resumen del contenido incluido en la página 8

The unit leaves the factory set at the CLOSE position. Locating hole Locating hole Screw hole Screw hole OPEN position CLOSE position (Mesh end toward back) (Mesh end toward front) Fan Cycle/Continuous - Cool Fan Cycle/Continuous - Heat (on some models) Class 2 (on some models) No function (reserved for future use) Fan Cycle/Continuous - Cool Fan Cycle/Continuous - Heat (on some models) Class 2 (on some models)

Resumen del contenido incluido en la página 9

Terminal connections location under front grille

Resumen del contenido incluido en la página 10

Grille Tab On some models On some models Grille Tab

Resumen del contenido incluido en la página 11

FRONT FRONT Dirty filter—Needs cleaning Clogged filter—Greatly reduces cooling, heating and airflow.

Resumen del contenido incluido en la página 12

• • • • • • • • • 12

Resumen del contenido incluido en la página 13

Phillips-head screwdriver Ruler or Tape Measure Scissors or knife Drill Hand or Saber Saw Level Pencil Adjustable Wrench 13

Resumen del contenido incluido en la página 14

1 4 Locking plate 5 Remove screw Base pan Power cord Clamp 2 6 Remove shipping pads (if present) 3 14

Resumen del contenido incluido en la página 15

3 1 ° Inside Top of case 2 Outside Caulking Undercut mortar Brick veneer Lintel angle (if required) Plaster line Caulking (on all 4 sides on the outside Trim molding and inside (if desired) of the case) Caulking (above Room side and below the flashing) Flashing (drip rail) 1/4 min. extension inside the wall from the trim molding 15

Resumen del contenido incluido en la página 16

(holes are on the right) Vinyl window gasket Sill support bracket (2) Case side gasket (2) 2 angles (left and right Foam top hand) window gasket Spring Case top gasket clip (4) B A Bottom window gasket Right side Left side Filler Panels Window locking Cut panels bracket and discard center piece Air conditioner Support bracket hardware Spacer (2) Type C (painted) (6) Type A (9) Type D (2) Lock nut (2) Type E (4) Adjusting bolt (2) Type B (2) Large washer (2)

Resumen del contenido incluido en la página 17

2 Wood 1/2 higher than frame Stool Storm window frame 3 F A B C Locking plate Remove shipping pads Remove (if present) screw G D Clips Remove screw Insert the 2 long screws Insert the 2 short screws E on the outside on the inside 17 Sill

Resumen del contenido incluido en la página 18

4 B A Centerline Centerline Sill Sill Outside Outside 3 3 3 3 12 ⁄8 12 ⁄8 13 ⁄8 13 ⁄8 Inside Inside Stool Stool 5 C A Type B Average sill Type E Spacer Spacer mounting screws Type (A) Sill support Sill support Spacer Narrow sill Lock nut Adjusting bolt Large washer (for use with wood sills) Offset sill (such as brick or stone) B • Screws are in position • • Sill support “V” notch Inside Stool Bolt Sill Outside 18

Resumen del contenido incluido en la página 19

(holes are on the right) Angle 6 Gasket A Angle Sill Window track Type C (painted Outside screws) Gasket Panel 3 3 13 ⁄8 13 ⁄8 Tab A Width of the air B conditioner Inside Left side (panel marks) Right side D B 3 B A Right Left side side Filler Panels Cut panels and discard center piece Hook the tab into the sill support C 19 (holes are on the left)

Resumen del contenido incluido en la página 20

7 E A F B G Put the gasket on top of the case where the window will close. Bottom window gasket C H Case holes Panel tab • • D Vinyl window gasket Panel tabs I Attach the panel tab Case to the window on each side screws with a type D screw. 20