Resumen del contenido incluido en la página 1
Installation
Frontload Washers
NOTA: El manual en
español aparece después
del manual en inglés.
H370I
H3
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 801561R1
May 2004
www.comlaundry.com
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Replacement Parts.............................................................................. 3 Table of Installation........................................................................................... 5 Dimensions and Specifications............................................................. 5 Contents Before You Start................................................................................... 6 Tools ............................................................................
Resumen del contenido incluido en la página 4
Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 801561 2
Resumen del contenido incluido en la página 5
Replacement Parts If replacement parts are required, contact the source Alliance Laundry Systems from which you purchased your washer, or contact: Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. Phone: (920) 748-3950 for the name and address of the nearest authorized parts distributor. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 801561 3
Resumen del contenido incluido en la página 6
Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 801561 4
Resumen del contenido incluido en la página 7
Installation Dimensions and Specifications 44.8 cm (17.5 in.) 37.9 cm (14.9 in.) 71.1 cm 68.3 cm (28 in.) (26.9 in.) 5.1 cm (2 in.) FLW2007N FLW2007N © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 801561 5 109.2 cm (43 in.) 93 cm (36.6 in.) 79 cm (31.1 in.) 75.1 cm (29.6 in.)
Resumen del contenido incluido en la página 8
Installation Water Before You Start Washer needs two standard 19.1 mm (3/4 in.) water Tools supply faucets with a pressure between 138 and For most installations, the basic tools you will need 827 kPa (20 to 120 pounds per square inch). For more are: detailed information refer to section on Water Supply Requirements. 3 2 4 Accessories Bag 1 An accessories bag has been shipped inside your washer. It includes: Two inlet hoses with washers. Refer to step 2 of Installation. Four rubber fee
Resumen del contenido incluido en la página 9
Installation Step 2: Connect Water Inlet Hoses Installing the Washer NOTE: Refer to section on Water Supply NOTE: If the washer is delivered on a cold day Requirements before connecting water inlet hoses. (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to Turn on the water supply faucets and flush the lines for operate it until the washer has had a chance to approximately two minutes to remove any foreign warm up. materials that could clog
Resumen del contenido incluido en la página 10
Installation Step 3: Connect Drain Hose to Drain Receptacle 1 2 Remove the drain hose from its shipping position on WATER MIXING the rear of the washer by unhooking the hose from the VALVE retainer clamp and by removing shipping tape. Find the instructions, on the following pages, that are appropriate for your type of drain receptacle (standpipe, sink, wall, or laundry tub). Follow these instructions to properly install the drain hose. IMPORTANT: Drain receptacle must be capable of handl
Resumen del contenido incluido en la página 11
Installation In-the-Wall Installation For installations of this type, the drain hose MUST be secured to one of the inlet hoses using the beaded tie- down strap from accessories bag. NOTE: End of drain hose must not be below 61 cm 1 (24 in.). 1 2 3 FLW2010N 2 1 61 to 91.44 cm (24 to 36 in.) Recommended Height 2 Standpipe – 5.08 cm (2 in.) or 4 cm (1-1/2 in.) 3 Beaded Tie-Down Strap Figure 6 3 Sink Installation H023I For this type of installation, use the beaded tie-down 1 Drain Hose strap (
Resumen del contenido incluido en la página 12
Installation Laundry Tub Installation Step 4: Position and Level the Washer For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from WARNING dislodging during use. Use the beaded tie-down strap Washers elevated above floor level must be (supplied in accessories bag) to secure hose. anchored to that elevated surface, base or platform. The material used to elevate the washer should also be anchored to the floor to ensure that the washer will n
Resumen del contenido incluido en la página 13
Installation NOTE: DO NOT slide washer across floor if the Step 5: Remove the Shock Sleeves and leveling legs have been extended, as legs and base Shipping Brace could become damaged. Remove front access panel by removing the two NOTE: Use of the dispenser drawer or washer door screws. as a handle in the transportation of the washer may Remove bolts and lockwashers from shipping brace cause damage to the dispenser or door. with 9/16 in. wrench and remove brace. Remove shock sleeves by pu
Resumen del contenido incluido en la página 14
Installation Step 6: Wipe Out Inside of Washer Drum 1 Before using the washer for the first time, use an all- purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside the drum. 2 4 3 H336I H337I 1 Shock Sleeves Figure 12 2 Motor Mount 3 Bolts and Lockwashers Step 7: Connect the Washer to Electrical 4 Hooked End of Shipping Brace Power Figure 11 Refer to section on Electrical Requirements and connect the washer to an electrical power source. W
Resumen del contenido incluido en la página 15
Installation Step 8: Check Installation Electrical Requirements Refer to Installer Checklist on the back cover and NOTE: The wiring diagram is located behind the make sure that unit is installed correctly. control panel, inside the control hood. Moving Unit to a New Location To prevent damage while moving the unit, the WARNING shipping materials MUST BE reinstalled. To reduce the risk of fire, electric shock, Reinstallation of Shipping Materials serious injury or death, all wiring and Disc
Resumen del contenido incluido en la página 16
Installation 240 Volt, 50 Hertz 120 Volt, 60 Hertz with 3-Prong Grounding Plug The washer is designed to be operated on a separate branch, polarized, three-wire, effectively earthed, The washer is designed to be operated on a separate 240 Volt, 50 Hertz, AC (alternating current) circuit branch, polarized, three-wire, effectively earthed, 120 protected by a 10 Ampere fuse, equivalent fusetron or Volt, 60 Hertz, AC (alternating current) circuit circuit breaker. protected by a 15 Ampere fus
Resumen del contenido incluido en la página 17
Installation Water Supply Requirements 2 1 3 WARNING Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. 120 ± 12 0 HYDROGEN GAS IS EXPLOSIVE. If the hot V.A.C. V.A.C. water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow 5 from each for several minutes. This will 120 ± 12 release any accumulated hydrogen gas. The V.A.C. gas is flammab
Resumen del contenido incluido en la página 18
Installation Water Temperature Water Pressure Cold: Pressure must be a minimum of 138 to a maximum of 827 kPa (20 to 120 pounds per square inch) static Recommended cold water temperature is 16° to pressure measured at the faucet. 27° Celsius (60° to 80° Fahrenheit). NOTE: Water pressure under 138 kPa (20 pounds Hot: per square inch) will cause an extended fill time in Recommended hot water temperature is 49° to the washer and may not properly flush out the 60° Celsius (120° to 140° Fahren
Resumen del contenido incluido en la página 19
Installation Information for Handy Reference Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. Date Purchased Model Number Serial Number Dealer’s Name Dealer’s Address Phone Number Service Agency Service Agency Address Phone Number NOTE: Record the above information and keep your sales slip. Model and serial numbers are located on the nameplate. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 801561 17
Resumen del contenido incluido en la página 20
