Instruction d'utilisation Harbor Freight Tools 32940

Résumé du contenu de la page N° 1

®
Air Hammer
Model 32940
Assembly and Operation Instructions
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions an

Résumé du contenu de la page N° 2

Specifications 1 Air Inlet / ”-18 NPT 4 Maximum Operating Pressure 90 PSI Blows Per Minute 4,500 BPM Average Air Consumption 4 CFM 1 Weight 2- / Lbs. 4 Accepts standard 10mm shank chisels. Save This Manual You will need the manual for the safety warnings and precautions, assembly instruc- tions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and d

Résumé du contenu de la page N° 3

9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect air hose when not in use. 11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the t

Résumé du contenu de la page N° 4

stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: - Lead from lead-based paints - Crystalline silica from bricks and cement or other masonry produc

Résumé du contenu de la page N° 5

Assembly / Installation 1 1. You will need to prepare the / ” Quick-disconnect Coupler Plug to connect to the air 4 inlet on the Air Hammer. Wrap the Coupler Plug with pipe thread seal tape before 3 threading it into the Air Inlet (9). Connect the a Quick-Disconnect coupler on a / ” ID 8 Air Source Hose to the tool. Note: If you are not using an automatic oiler system, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Add a few drops more after each hour of c

Résumé du contenu de la page N° 6

Operation Retainer Spring (15) Cylinder (14) Chisel Trigger (16) Regulator (4) Air Inlet (9) Examine your chisels/bits before using them. If a chisel is dull or cracked do not use it. Replace worn or broken chisels with approved replacement chisels/bits from Harbor Freight Tools. Warning!! Always disconnect the tool from the air source before examining or changing bits. 1. Select the appropriate chisel/bit. Unscrew the Retainer Spring (15) and insert the shank of the chisel/bit. Screw the Re

Résumé du contenu de la page N° 7

Maintenance (Continued) 4. Examine your chisels/bits before using them. If a chisel is dull or cracked do not use it. Replace worn or broken chisels with approved replacement chisels from Harbor Freight Tools. Assembly Diagram Parts List Pn artD. escriptio Qt tyPn arD. escriptio Qty 1yB1 od 1e 0 R1 ear Valv 2tR1 ubber Gaske 1k1 V1 alve Dis 3gO2 -Rin 1e 2 F1 ront Valv 4rR1 egulato 1n3 P1 isto 5nC1 ontrol Pi 1r4 C1 ylinde 6gO1 -Rin 1g 5R1 etainer Sprin 7lB1 al 1r 6 T1 rigge 8gS1 prin 1n7 P1 i 9tA