ページ1に含まれる内容の要旨
qrtitle.book Page i Friday, December 18, 1998 9:52 AM
MDW 9031/9031DCP
Wireless Pocket Phone Quick Reference
503-801-165
Comcode 108406844
February 1999
Issue 2
ページ2に含まれる内容の要旨
qrtitle.book Page ii Friday, December 18, 1998 9:52 AM DE Copyright © 1999 by Lucent Technologies. All rights reserved. DEFINITY, MERLIN, MERLIN LEGEND and PARTNER are registered trademarks of Lucent Technologies. The order number for this book is 503-801-165. To order additional copies of this book, call 1 800 457-1235 or 317-322-6791.
ページ3に含まれる内容の要旨
qrtitle.book Page iii Friday, December 18, 1998 9:52 AM Contents Quick Reference 1 Handset Controls . . . . . . . . . . . . . . . . . . . . . . 1 Handset Display . . . . . . . . . . . . . . . . . . . . . . . 2 Line Status Indicators . . . . . . . . . . . . . . . . . . . . 3 Volume Adjustment . . . . . . . . . . . . . . . . . . . . . 4 Battery Charger LEDs . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
qrtitle.book Page iv Friday, December 18, 1998 9:52 AM
ページ5に含まれる内容の要旨
qrtitle.book Page 1 Friday, December 18, 1998 9:52 AM Quick Reference Handset Controls Receiver Headset On/Off Receives the sound Press to turn the headset on of your caller's voice, if the headset is plugged in. unless a headset is ON appears in handset connected. display. To turn off, press Antenna again. Turn on to make or answer a call, and turn off to Extend fully to “hang up.” maximize the handset range and voice Lanyard Loop quality. Attach lanyard for Handset Display carrying handse
ページ6に含まれる内容の要旨
qrtitle.book Page 2 Friday, December 18, 1998 9:52 AM Quick Reference Handset Display 3 4 5 6 1 2 7 9 8 1 Information you would see on a wired system phone’s display, (except time), based on your communications system: LCL:P, D, M1, or M2 = Local Mode: communications system WIRELESS TEST = Handset in Wireless Test Mode VIBR = Vibrator enabled PSEL = Line Preselection enabled PRESELECTION:ON/OFF = Line Preselection Mode:status CHANGE BUTTN MAP = Communications system setting is wrong MAP:
ページ7に含まれる内容の要旨
qrtitle.book Page 3 Friday, December 18, 1998 9:52 AM Quick Reference 8 Line Status Indicators show the status of line or programmable/intercom/drop buttons. See “Line Status Indicators” below. 9 Selection rectangle indicates the active row for line or programmable/intercom/drop button selection. When the display is blank, the handset is either turned off or in “sleep” mode. Activate the display by pressing O or " . Line Status Indicators Each line status indicator corresponds to a sp
ページ8に含まれる内容の要旨
qrtitle.book Page 4 Friday, December 18, 1998 9:52 AM Quick Reference Volume Adjustment To increase or decrease the volume of the handset alerter or the receiver (earpiece): • Alerter: Press the “+” or the “-” button while the MDW 9031/9031DCP is awake but turned off. If the display is dark (the phone is in “sleep” mode), press " to wake it up, then press the “+” or the “-” button. • Receiver: Press the “+” or the “-” button while the MDW 9031/9031DCP is turned on. MDW 9031/9031D
ページ9に含まれる内容の要旨
qrtitle.book Page 5 Friday, December 18, 1998 9:52 AM Quick Reference Battery Charger LEDs The color of the battery charger’s LEDs indicates the state of the corresponding battery pack, as shown in the following table: Battery If it is the If it is the If it is the charger LED SPARE LED, HANDSET REFRESH LED, shows... the battery LED, the the Refresh pack in the battery pack button was Spare battery in the pressed, and compartment... Handset... the Handset battery pack... Steady orange
ページ10に含まれる内容の要旨
qrtitle.book Page 6 Friday, December 18, 1998 9:52 AM Quick Reference Help! MDW 9031 ® If you need help when using your MDW 9031 with a PARTNER , ® ® MERLIN , or MERLIN LEGEND system in the continental U.S., call 1 800 628-2888. MDW 9031DCP ® If you need help when using your MDW 9031DCP with a DEFINITY system in the continental U.S., call 1 800 225-7585, or contact the Lucent Customer Care Center at 1 800 241-2121. For all other systems, follow the procedure you normally use to get sup
ページ11に含まれる内容の要旨
qrtitle.book Page 7 Friday, December 18, 1998 9:52 AM Quick Reference Preselecting a Line or Button After Line Preselection is enabled, proceed as follows: 1 If the display is blank, press " . 2 If necessary, press " to move the Selection rectangle. 3 Press ' corresponding to the line or button you want. 4 Press O to access the line or button. Accessing Certain Voice Mail Systems with a DEFINITY System Note: This section only applies to the MDW 9031 Pocket Phone. After dialing i
ページ12に含まれる内容の要旨
qrtitle.book Page 8 Friday, December 18, 1998 9:52 AM Quick Reference Changing Settings or Performing Tests in Local Mode 1 Make sure the handset is turned off. 2 Press and hold " for 3 seconds. 3 While still holding " , press O. 4 Press one of the following: A (2) to enable or disable the alerter. L (5) to enable or disable backlighting. P (7) for 3 seconds, then " to enable or disable Line Preselection. V (8) to enable or disable the vibrator. W (9) to enter Wireless Test Mode
