ページ1に含まれる内容の要旨
DVD PLAYER
XD-DV370
OPERATING INSTRUCTIONS
8A-AV4-906-11
000731BMK-Y-L K
ページ2に含まれる内容の要旨
PREPARATION WARNING WARNING (FOR USE IN THE UNITED KINGDOM) TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This appliance is supplied with a fitted three pin mains plug. A 13 amp fuse is fitted in the plug. Should the fuse need to be replaced, use a 13 amp fuse approved by ASTA or BSI to BS 1362. When replacing the CAUTION fuse, you must ensure that any removable fuse covers are RISK OF ELECTRIC SHOCK correctly refitted. DO NOT OPEN If you should
ページ3に含まれる内容の要旨
IMPORTANT SAFETY Electric power 1 Power sources — Connect this unit only to power INSTRUCTIONS sources specified in the Operating Instructions, and as marked on the unit. 2 AC power cord Read the Operating Instructions carefully and completely - When disconnecting the mains lead, pull it out by the before operating the unit. Be sure to keep the Operating mains plug. Do not pull the mains lead itself. Instructions for future reference. All warnings and cautions - Never handle the mains plug with
ページ4に含まれる内容の要旨
TABLE OF CONTENTS points (A-B Repeat) ................................... 30 Programmed playback ........................................... 31 Introduction Creating a 3D surround effect .............................. 32 Changing the audio track ...................................... 33 Precautions ............................................................... 2 Changing audio tracks (DVD) ......................... 33 Before Use .................................................................
ページ5に含まれる内容の要旨
BEFORE USE Please read the following before operating the DVD player. Note on DTS-encoded CDs When playing DTS-encoded CDs, excessive noise will be exhibited from the analogue stereo outputs. To avoid possible Supported disc formats damage to the audio system, the consumer should turn down the volume before playing back such a disc, adjust the volume This DVD player can play discs with the following marks gradually, and keep the volume level low. To enjoy DTS Digital only. TM Surround playback,
ページ6に含まれる内容の要旨
BEFORE USE (CONTINUED) Cleaning discs Handling the unit Fingerprints and dust on the disc can cause poor picture When shipping the DVD player quality and sound distortion. Before playing, clean the disc The original shipping carton and packing materials come with a clean cloth. Wipe the disc from the center out. in handy. For maximum protection, re-pack the unit as it was originally packed at the factory. When setting the DVD player The picture and sound of a nearby TV, VCR or radio may be disto
ページ7に含まれる内容の要旨
PARTS AND CONTROLS The instructions in this manual refer mainly to the buttons on the remote control. Buttons on the main unit with the same names as those on the remote control can be used as well. Front panel 2 3 456 7 !0 8 # @ 1 9 POWER button g/t button 1 9 Press to turn on and off the unit. Press to skip to the next track. Hold down to playback a 6STANBY/ON indicator disc forward. 2 • Lights in red when the unit is in standby mode. MENU button 0 • Lights in green when the unit is turned
ページ8に含まれる内容の要旨
PARTS AND CONTROLS (CONTINUED) Remote control 0OPEN/CLOSE button @ ! Press to open and close the disc tray. # !MARK SEARCH button Press to display the marked point on the TV screen $ 0 during playback or stop mode. % ZOOM button @ 9 Press to enlarge the picture during a DVD playback. ^ REPEAT button # & Press to execute a repeat playback. $SURROUND button 8 * Press to turn on and off the 3D surround effect. ( %A-B button 7 ) Press to memorize the point you want to repeat. - ^ANGLE button 6 = Pr
ページ9に含まれる内容の要旨
Display window This player shows On-Screen Display messages on the screen of the TV set to which the DVD player is connected, as well as those on the display window of the unit. The On-Screen Display messages, which accompany each operation of the unit, make operation simple and easy especially when playing DVDs or video CDs. They are also displayed when pressing the ON SCREEN DISPLAY ON /OFF button on the remote control. The instructions in this manual refer mainly to the On-Screen Display mess
ページ10に含まれる内容の要旨
CONNECTIONS At first, decide the outline of the connection among this unit, your TV set and the amplifier, etc. It is necessary to set the setup menu of this unit according to the connection. Before connection, identify the type of your audio equipment or of the TV set referring to the following chart. Then decide the connection and the setup menu according to the types. Audio system to be connected Input jack of equipment to be Referring connected to the DVD player Letter None (only the tele
ページ11に含まれる内容の要旨
A Connecting to a TV set only Rear of TV set 21 pin scart connector 21 pin scart cable (not supplied) to 21 pin scart connector Rear of the unit AUDIO DIGITAL OUT OUT L COAXIAL DIGITAL OUT S-VIDEO R NTSC PAL AUTO VIDEO OUT OPTICAL OUT to an AC power socket (AC 230 V, 50 Hz) When your TV set is equipped with an S-video input terminal, see page 17. Set the setup menu correctly after connecting! NOTE According to the audio equipment and TV set to which the When the picture noise appears while copy-
ページ12に含まれる内容の要旨
CONNECTIONS (CONTINUED) B Connecting to a TV set and an amplifier with a Digital In jack Use either the commercially available optical cord or 75 ohm coaxial cord when connecting this unit to an AV amplifier with a Digital In jack. The supplied video cord is also available instead of the coaxial cord. TV set to 21 pin scart connector 21 pin scart cable (not supplied) to 21 pin scart connector Rear of the unit DIGITAL OUT AUDIO OUT L COAXIAL DIGITAL OUT S-VIDEO R NTSC PAL AUTO VIDEO OUT OPTICAL O
ページ13に含まれる内容の要旨
C Connecting to a TV set and an audio system TV set to 21 pin scart connector 21 pin scart cable (not supplied) to 21 pin scart connector DIGITAL OUT AUDIO OUT L COAXIAL DIGITAL S-VIDEO OUT R NTSC PAL AUTO VIDEO OUT OPTICAL OUT white to AUDIO OUT L (white)/ R (red) jacks red to an AC power socket Audio cord (supplied) (AC 230 V, 50 Hz) to an audio input jacks (Left/ white, Right/ red) Audio system When your TV set is equipped with an S-video input terminal, see page 17. Set the setup menu correc
ページ14に含まれる内容の要旨
CONNECTIONS (CONTINUED) D Connecting to an AV amplifier equipped with a Dolby Digital (AC-3) decoder Use either the commercially available optical cord or 75 ohm coaxial cord when connecting this unit to an AV amplifier with a Digital In jack. The supplied video cord is also available instead of the coaxial cord. TV set to 21 pin scart connector 21 pin scart cable (not supplied) to 21 pin scart connector Rear of the unit DIGITAL OUT AUDIO OUT L COAXIAL DIGITAL OUT S-VIDEO R NTSC PAL AUTO OUT VID
ページ15に含まれる内容の要旨
E Connecting to an AV amplifier equipped with a DTS decoder Use either the commercially available optical cord or 75 ohm coaxial cord when connecting this unit to an AV amplifier with a Digital In jack. The supplied video cord is also available instead of the coaxial cord. TV set to 21 pin scart connector 21 pin scart cable (not supplied) to 21 pin scart connector Rear of the unit DIGITAL OUT AUDIO OUT L COAXIAL DIGITAL OUT S-VIDEO R NTSC PAL AUTO VIDEO OUT OPTICAL OUT to DIGITAL OUT to DIGITAL
ページ16に含まれる内容の要旨
CONNECTIONS (CONTINUED) F Connecting to a TV set and an AV amplifier with the Dolby Pro Logic Surround system TV set to 21 pin scart connector 21 pin scart cable (not supplied) Rear of the unit AUDIO DIGITAL OUT OUT L COAXIAL DIGITAL OUT S-VIDEO R NTSC PAL AUTO VIDEO OUT OPTICAL OUT to AUDIO OUT white L (white)/ R (red) jacks red to an AC power socket Audio cord (supplied) (AC 230 V, 50 Hz) to an audio input jacks (Left/ white, Right/ red) Amplifier equipped with Dolby Pro Logic Surround Front F
ページ17に含まれる内容の要旨
Connecting to a TV set equipped with S-video jack Rear of TV set S-video input connector (S1, S2) S-video cord (not supplied) to S-VIDEO OUT connector Rear of the unit DIGITAL OUT AUDIO OUT L COAXIAL DIGITAL S-VIDEO OUT R NTSC PAL AUTO VIDEO OUT OPTICAL OUT to an AC power socket (AC 230 V, 50 Hz) Set the setup menu correctly after connecting! NOTE Set the "TV Output Select" and "TV Aspect" of the setup When the picture noise appears while copy-protected DVDs menu correctly referring to the follo
ページ18に含まれる内容の要旨
CONNECTIONS (CONTINUED) Connecting to a TV set or monitor with video input connector TV set or monitor to a video input jacks to an audio input jacks (yellow) (Left/ white, Right/ red) Yellow Audio cord (supplied) Video cord (supplied) Yellow White Red to VIDEO OUT to AUDIO OUT jack (yellow) Rear of the unit L (white)/ R (red) jacks DIGITAL OUT AUDIO OUT L COAXIAL DIGITAL S-VIDEO OUT R NTSC PAL AUTO VIDEO OUT OPTICAL OUT to an AC power socket (AC 230 V, 50 Hz) Set the setup menu correctly after
ページ19に含まれる内容の要旨
REMOTE CONTROL Installing batteries Detach the battery cover on the rear of the remote control, and insert two R6 (size AA) batteries with 0 and 9 aligned correctly. When to replace the batteries The maximum operational distance between the remote control and the sensor of the units should be approximately 7 meters. If this distance decreases, replace the batteries with new ones. NOTES • When operating with the remote control, point the top of the remote control toward the player. • If the unit
ページ20に含まれる内容の要旨
PLAYBACK Getting ready to play • Turn on the television, and set its video source (Video 1, Video 2, Video 3, etc.) to the one connected to the DVD player. • Turn on the audio device connected to the DVD player. i/k/j/l/ 2,4 1 Set its input source to the one connected to the DVD 3 ENTER player. s Press POWER. 1 The power comes on, and the 6STANDBY/ON indicator a MENU turns green. C MP3 VCD CD DVD TITLE CHP/TRK PROG. RANDOM ALL A B DVD Press zOPEN / CLOSE. 2 2,4 The disc tray opens. MP3 VCD CD DV
