ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
MEMO DISP SEL PWR 1 2 3 4 5 6 PRE CONGRATULATIONS! Box contents Safety precautions ® Your Here Anywhere™ Portable SIRIUS Satellite Tuner lets you enjoy SIRIUS Satellite’s digital entertain- Unpack your Here Anywhere carefully and make 2 2 Warning ment streams anywhere you’ve installed one of our KPA-H2H Home Docking Kits or KPA-H2C Car Docking sure that everything listed here is present: Take the following precautions to prevent traffic Kits (available separately). Use this manual to familiarize
ページ3に含まれる内容の要旨
• When replacing a fuse, use only a new one with instruction manual. The user could lose the authority • Connect the equipment into an outlet on a circuit Warning the proper rating. Using a fuse with the wrong to operate this equipment if an unauthorized change different from that to which the receiver is Take the following precautions to prevent fire and rating may cause the unit to malfunction. or modification is made. connected avoid personal injury: • To prevent a short circuit when replaci
ページ4に含まれる内容の要旨
Installation in a vehicle with the KPA-H2C kit (available separately) Installation in a vehicle (continued) Note: Do not put Here Anywhere in the docking station until you have completed the installation. 2 1. Determine where you want to mount 2. You can bend the leaves on the base to 5. Plug the cigarette lighter adapter 6A. Plug the cassette adapter 6B. If your car stereo has an aux input, plug 4. Using the provided screw, Here Anywhere. conform to curved mounting surfaces. into the back of th
ページ5に含まれる内容の要旨
Installation in a vehicle: Mounting the antenna Installation in a vehicle: Routing the cable Note: If you’re using the Kenwood CX-SR10 SIRIUS antenna, you’ll need to remove the plastic 8. Route the cable from the antenna to the vehicle’s interior by 9. Route the cable from the lowest point of the rear 1. Temporarily plug the antenna housings from the antenna connectors—we recommend labeling the wires with their respective tucking it underneath the rubber molding around rear window, window into
ページ6に含まれる内容の要旨
Installation in a home with the KPA-H2H kit (available separately) Installation in a home (continued) Note: Do not put Here Anywhere in the docking station until you have completed the installation. 2 5. Due to the paths of SIRIUS satellites over the US, the best location for the antenna in your 4. Plug the antenna into the back 3. Plug the AC cord into the power 1. Using the provided screw, 2A. Plug the audio 2B. Plug the audio home depends on where you live. Use the map below as a general pl
ページ7に含まれる内容の要旨
Front-panel controls and features Remote control functions U p / D o w n / L e f t / R i g h t POWER Button: Turns Here Anywhere on and off 2 Arrow B Buttons: Navigates Up/Down/Left/Right A Arrow B Buttons: Navigate through display screens through display screens SELECT Button: Press to select items highlighted on the display; hold-down to Display: Shows informa- jump to the previously-received Stream tion about streams, cate- gories, artists, songs and SETUP Button: Enters and exits the Setup M
ページ8に含まれる内容の要旨
4. Hold the POWER button for at least 1 second to Activating your SIRIUS subscription Basic operation enter the Setup Mode. Before you can listen to Here Anywhere, you must After you have successfully activated your 2 5. Your unit’s unique 12-digit SIRIUS ID Number will subscribe to SIRIUS Satellite’s service. SIRIUS subscription, the Normal Operation be displayed screen will appear (top right): 1. Make sure that Here Anywhere is properly 2 (right). Write the connected and that its antenna is
ページ9に含まれる内容の要旨
4. If you decide not to select another stream, press the POWER button to exit the mode. The display will Selecting music by artist (Artist List Mode) revert to the Normal Operation screen for the active stream. 1. While the Normal Operation screen is active, press • You can switch to the previously-selected stream by holding the SELECT button for at least 1 second. the DISPLAY button twice. The Artist List screen will Holding the SELECT button for 1 second again switches back to the original str
ページ10に含まれる内容の要旨
• After you make your selection, the display will revert to the Normal Operation screen 2. When the desired preset bank is displayed, use the “1” – “6” buttons to tune the desired preset stream Note: In the Stream List, Artist List and Song List modes, if you don’t want to make a selection, press the Searching for a stream preset (Preset List Screen) POWER button to exit the mode and return to the Normal Operation screen for the active stream. There are two ways you can search for a stream prese
ページ11に含まれる内容の要旨
Adjusting the display brightness Saving/recalling music information Hold the DISPLAY button down for over 1 second to Saving music information enter the Display Brightness mode (right): You can store the name of the currently-playing song and artist (and composer, if the data is available) into 1. Use the up & down arrow buttons to select the memory for recall later. desired brightness level (high/medium/low) Press the MEM button to save the data. The screen will display the following message (a
ページ12に含まれる内容の要旨
1. While in the Setup Mode, press the left or right arrow 2. Press the up or down arrow button. The Lock Code button until the Channel Skip screen appears (right): screen appears (top, right): 2. Use the up & down arrow buttons to highlight the 3. Using the preset 1 – 6 buttons, enter the factory stream you want. (The highlighted stream will default code “1 1 1 1”. The screen’s second line will automatically play.) change from “_ _ _ _” to “* * * *”. Channel Skip Screen Lock Code Screen 3. Press
ページ13に含まれる内容の要旨
8. Press the MEMORY button. The display will change to “New Code Confirmed” • “High” is 0dB, “Medium” is –3dB and “Low” is –6dB. • If you entered the code incorrectly, “Code Error” will be displayed, and the Enter New Lock Code screen Note: To avoid distortion with some cassette car stereos, you may have to lower the output level when using reappears. Repeat Steps 5 – 8. the cassette adapter. Startup Mode Antenna Signal You can select which screen is displayed when you turn This screen shows the
ページ14に含まれる内容の要旨
Troubleshooting guide Troubleshooting Guide (continued) Problem Possible Cause Solution Problem Possible Cause Solution Turn the power off (press the Power supply/cigarette lighter Make sure power supply/adapter POWER button), wait 5 – 10 adapter not properly connected is properly connected No power on Here Anywhere (power 2 seconds, then turn the power on indicator /display not illuminated) Blown fuse in cigarette lighter Check the fuse; if blown, replace again. adapter with supplied
ページ15に含まれる内容の要旨
