ページ1に含まれる内容の要旨
10M Ethernet
PC Card Adapter
Quick Installation Guide
ページ2に含まれる内容の要旨
FCC REGULATORY STATEMENTS Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interface, and 2. This device must accept any interface received, including interface that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pr
ページ3に含まれる内容の要旨
INTRODUCTION The PCMCIA Ethernet card is a credit-card-size Type II PCMCIA Ethernet adapter that complies with the PCMCIA 2.1 and IEEE 802.3 standards. It works with computers that incorporate a compatible interface. The drivers associated with this card allow you to use the most popular Network Operating System (NOS) in the PC environment very easily. System Requirement • An IBM compatible PC with 386SX or higher • At least one type II PCMCIA socket • Drivers and utilities provided
ページ4に含まれる内容の要旨
• Windows 95 • Windows 98 • Windows ME • Windows 2000 • Windows XP • Lantastic 6.0 • IBM OS/2 Warp Version 3 Physical Specification • PCMCIA Type II • 3.37 in. x 2.128 in. x 0.197 in. • 85.6mm x 54mm x 5mm • Weight: 35 g • Power: +5V ±5%, @150mA - 2 -
ページ5に含まれる内容の要旨
INSTALLATION Hardware Connections 1. Insert the PCMCIA Ethernet card into the PCMCIA slot with the 68 pin connector toward your notebook’s PCMCIA slot and the label facing up. 2. Connect the media coupler to the PC card’s 15-pin connector. 3. Connect one end of an Ethernet cable to the coupler media. Plug the other end of the cable into a switch hub. Software Installation Insert the driver diskette into the floppy drive and set the current drive to the floppy drive. Then run IN
ページ6に含まれる内容の要旨
2. Please input the path, A:\ and insert driver diskette. The driver will be installed and you may be asked for the original Windows 95 CD/disks. 3. For the first time installation, please click Network icon in Control Panel to add Protocols, Client and Service if you needed 4. Reboot the machine and the card will be fully functional. Windows 98 Installation Make sure that the drivers of PC Card slot are well installed. The System Icon in the Status Area can report on its function
ページ7に含まれる内容の要旨
2. Select Search for the best… and press Next. 3. Select Floppy disk drives and insert driver diskette. Then press Next, the driver will be installed. 4. Click Next to continue. Windows will start to copy the appropriate driver to your system. If Windows asks you to supply your original Windows 98 installation CD-ROM, load it in the CD-ROM drive. 5. For the first time installation, please click Network icon in Control Panel to add Protocols, Client and Service if you needed. 6
ページ8に含まれる内容の要旨
Windows ME Installation 1. Once the PC Card is connected to your computer, Windows will automatically detect the new device. Insert the device Driver Disk into the floppy disk drive of your system. Select Automatic search for a better driver (Recommended) and click Next. 2 Windows will copy the appropriate driver to your system. If Windows ME asks you to supply your original Windows ME installation CD-ROM, load it in the CD-ROM drive. 3 Click Finish to complete the software insta
ページ9に含まれる内容の要旨
Windows NT 4.0 1. Make sure that the Network Services already installed in the NT 4.0 system. 2. Insert the Ethernet Adapter into one of the system's PCMCIA Slots 3. Power up Windows NT 4.0 4. Open My Computer 5. Open Control Panel 6. Run the Network 7. Select Adapters page 8. Press Add to add network adapter 9. Press Have Disk button 10. Insert the driver disk into drive A: 11. Specify the path to ” A:\ and press OK 12. A dialog box will appear to adjust the driver's settings. T
ページ10に含まれる内容の要旨
2. Select Search for a suitable driver for my device (recommended). Click Next. 3. Select Floppy disk drives and insert the disk associated with the PCMCIA Ethernet card in the disk drive. Click Next. - 8 -
ページ11に含まれる内容の要旨
4. Click Next to make Windows install the appropriate driver for the new device. 5. Click Yes to continue. - 9 -
ページ12に含まれる内容の要旨
6. Click Finish to complete the software installation. Windows XP Installation 1 Once the device is connected, Windows will automatically detect the new device. Insert the device Driver Disk into the floppy disk drive of your system. Click Install the software automatically (Recommended) and click Next. - 10 -
ページ13に含まれる内容の要旨
2. Click Continue Anyway to proceed. 3. Wait while Windows copies the appropriate driver to your system. 4 Click Finish to complete the software installation. - 11 -
ページ14に含まれる内容の要旨
- 12 -
