ページ1に含まれる内容の要旨
H-CMD4015
MULTIMEDIA DVD/CD/MP3 RECEIVER WITH BUILT-IN 4.3” TFT DISPLAY AND TV TUNER
Instruction manual
DVD/CD/MP3- 4,3” TFT-
ページ2に含まれる内容の要旨
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ...............................................................................................................................................2 Important safeguards .....................................................................
ページ3に含まれる内容の要旨
Important safeguards Using the device at temperature below -10º may cause the breakage of the device. Before using, please, heat up the passenger compartment to the recommended temperature! Read carefully through this manual to familiarize yourself with this high-quality car stereo system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperag
ページ4に含まれる内容の要旨
Accessories HEXAGON NUT 1 PCS MOUNTING BOX 1 PCS LEFT KEY 1 PCS RIGHT KEY 1 PCS METAL BAR 1 PCS CONNECTOR ISO 1 PCS PLAIN WASHER ( =5mm) 1 PCS CARRY CASE 1 PCS GPS EXTERNAL ANTENNA 1 PCS SPRING WASHER ( =5mm) 1 PCS TV ANT WIRE 1 PCS AV IN WIRE 1 PCS SCREW ( 5X5mm) 4 PCS SCREW ( 5X25mm) 1 PCS CUSTOMER INFORMATION 1 PCS WARRANTY CARD 1 PCS INSTRUCTION MANUAL 1 PCS GPS NAVIGATION INSTRUCTION MANUAL 1 PCS 4
ページ5に含まれる内容の要旨
Installation/connection Notes: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring and make sure that the unit works properly. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency
ページ6に含まれる内容の要旨
1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. 2. Disconnect the wire harness and the antenna. 3. Press RELEASE button to remove the control panel. 4. Lift the top of the outer trim ring then pull it out to remove it. 5. Use the two supplied release keys to remove the unit from the mounting bracket. Insert the left ("L") and right ("R") release keys as far as they will go (with the notches facing up) into the appropriate s
ページ7に含まれる内容の要旨
9. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This metal strap al
ページ8に含まれる内容の要旨
2. DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow this mounting instruction. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Fasten the unit to the factory radio mounting brackets. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on each side. Note: The outer trim ring, mounting sleeve and the me
ページ9に含まれる内容の要旨
2. Pull off the front panel from the main unit. Store the front panel in the protective case provided for safe keeping. TO ATTACH THE FRONT PANEL First fasten the right side of the front panel onto the bracket of main unit. Then slightly push the left side of the front panel to attach the main unit. 9
ページ10に含まれる内容の要旨
Electrical Connection Note: The parking wire is connected with brake signal; for safety, the programs can be seen on the monitor after braking the car. 10
ページ11に含まれる内容の要旨
Connecting the reversing line to taillight on the car After connecting, when you start up the reverse gear, the unit will receive the picture from car rear view camera. 11
ページ12に含まれる内容の要旨
Unit controls Front panel 1. POWER/MUTE button 2. MENU button 3. RELEASE button 4. AF/REG button 5. EJECT button 6. TA button 7. BAND button 8. DISPLAY button 9. AS/PS button 10. PTY button 11. USB jack 12. PLAY/PAUSE button 13. IR sensor 14. Touch screen 15. AV in jack 16. VOL+/VOL-, PREVIOUS/NEXT buttons 17. SOURCE button 12
ページ13に含まれる内容の要旨
Inner panel 18. Card slot for GPS Map card 19. Disc slot 20. LED indicator 21. RESET button 22. SD/MMC Memory card slot 13
ページ14に含まれる内容の要旨
Remote control 1. POWER/LIGHT button 2. MODE/SMART button 3. SETUP button 4. SUB-T button 5. ANGLE button 6. PREVIOUS/NEXT, FAST REWIND/ FAST FORWARD/Cursor buttons 7. ENTER button 8. DISPLAY button 9. ZOOM button 10. BAND button 11. Digit buttons 12. 9/PTY button 13. 7/TA button 14. 8/AF/REG button 15. RPT button 16. 0 button 17. SOURCE button 18. EJECT button 19. SYS/DVD/TV switch 20. INFO button 21. DVD MENU button 22. MUTE button 23. TITLE button 24. VOL+/VOL- buttons 14
ページ15に含まれる内容の要旨
25. AUDIO button 26. PLAY/PAUSE button 27. STEP button 28. STOP button 29. GOTO/AS/PS button 30. PROGRAM/LO/DX button 31. RDM/MO/ST button 32. A-B button Changing the battery 1. Press the catch and at the same time pull out the battery tray (pic. 1). 2. Insert the 1 lithium battery, type CR2025 (3V) battery with the stamped (+) Pic. 1 Pic. 2 mark facing upward. Insert the battery tray into the remote control (pic.2). Warning: Store the battery where children cannot reach. If a child accidentall
ページ16に含まれる内容の要旨
General operations Reset the Unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Remove the front panel at first, and then press RESET button on the inner panel of the unit with a pointed object, (such as a ballpoint pen) to set the unit to initial state. Note: When some errors occur on the display, you can also press RESET button to resume to normal, and it will erase some memorized functions. Turning the Unit On/Off Press any button (except R
ページ17に含まれる内容の要旨
Volume Control Press VOL+/VOL- button on the RC or on the unit to increase/decrease the sound level. Mute Function Press MUTE button on the RC or on the unit to turn off the sound. The corresponding icon appears on the TFT. Press it again to resume the previous volume level. System (SYS) DVD/TV joyswitch Move the joyswitch to SYS, DVD or TV, to use the buttons on the remote control served for system, DVD or TV playback. Otherwise you will not able to use the buttons. Source choose Press SOURCE b
ページ18に含まれる内容の要旨
Dual zone Pressing and holding SMART/MODE button on the RC, you can turn on or off the dual zone playing mode. After turning on dual zone playing mode, press SMART/MODE button to select the playback mode for rear zone: MEDIA => TV => AV1 => AV2. Last Position Memory During the media playback (DISC, USB, SD/MMC CARD), if you turn off the unit and then switch on it, the unit will resume playing from the point that it was interrupted. During the media playback (DISC, USB, SD/MMC CARD), if you switc
ページ19に含まれる内容の要旨
System Information Display In media playback mode, TV or auxiliary AV1/AV2 input mode, press the DISP button on the remote control, the TFT screen will show such kind of system information, such as real time, volume level, current playback mode of rear zone etc. 19
ページ20に含まれる内容の要旨
Using the touch screen control The Touch Screen Control allows fingertip control of virtually all functions. Alternatively, you could also operate with ease with the user-friendly integrated big function buttons that are prominently visible. To access the main control interface In every playback mode, when you press the SOURCE button in the head unit, or click the icon on the touch screen, the main control interface will pop up. To select a source (Media, GPS, TV, AV 1, AV 2 or Radio), click th
