Amtrol WELL-X1の取扱説明書

デバイスAmtrol WELL-X1の取扱説明書

デバイス: Amtrol WELL-X1
カテゴリ: 水道システム
メーカー: Amtrol
サイズ: 2.75 MB
追加した日付: 9/21/2014
ページ数: 16
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスAmtrol WELL-X1の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Amtrol WELL-X1に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Amtrol WELL-X1をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Amtrol WELL-X1のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Amtrol WELL-X1の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Amtrol WELL-X1 取扱説明書 - Online PDF
Advertisement
« Page 1 of 16 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Amtrol WELL-X1を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Amtrol WELL-X1の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

INSTALLATION, OPERATION
West Warwick, Rhode Island 02893
& MAINTENANCE
INSTRUCTIONS
® ™
WELL-X-TROL WELL-X1
INSTALLER: LEAVE THIS MANUAL WITH THE OWNER
IMPORTANT GENERAL SAFETY INFORMATION - ADDITIONAL SPECIFIC SAFETY ALERTS APPEAR IN THE FOLLOWING INSTRUCTIONS.
READ CAREFULLY THE PRODUCT INSTALLATION, OPERATING AND MAINTENANCE MANUAL. FAILURE TO FOLLOW
THE INSTRUCTIONS AND WARNINGS IN THE MANUAL MAY RESULT IN SERIOUS OR FATAL INJURY AND/OR PROPERTY DAMAGE,
AND WILL VOID THE PRODUCT WARRANT

ページ2に含まれる内容の要旨

1. TABLE OF CONTENTS GENERAL SAFETY INFORMATION ........................................................... 2 COMPONENTS ........................................................................................... 3 INSTALLATION AND SIZING CONSIDERATIONS ..................................... 4 INSTALLATION CONSIDERATIONS........................................................... 5 PLUMBING .................................................................................................. 6 WIRING

ページ3に含まれる内容の要旨

3. COMPONENTS ™ The Well-X1 combines all the standard well tank components in a single, easy to install package. The pressure tank, ™ control and tank fittings are factory-installed. After removing from the carton, inspect the Well-X1 for damage and ensure all components are present. COVER RELIEF VALVE CONDUIT HOLES MOUNTING KNOB AIR CHARGING VALVE PUMP & POWER WIRES WATER CONNECTIONS(2) PRESSURE SENSOR TUBING CONTROL MOUNTING BRACKET TANK TUBING PRESSURE TANK DRAIN 3

ページ4に含まれる内容の要旨

4. INSTALLATION AND SIZING CONSIDERATIONS ™ The Well-X1 functions like a traditional pressure switch by cycling the pump on and off. The factory pressure settings are 40 psi cut-in and 60 psi cut-out. The controller allows these settings to be adjusted to best suit the application. The ™ Well-X1 can operate in two primary modes: A. STANDARD OPERATION ™ Using a standard 20 psi differential, the Well-X1 can be sized according to the chart below. In this application, the sizing and performance

ページ5に含まれる内容の要旨

5. INSTALLATION CONSIDERATIONS LOCATION ™ The Well-X1 is designed for indoor and outdoor installations. The NEMA 3R enclosure can be installed in direct weather. If installed outdoors, be sure the following conditions are met: • Do not install where ambient temperatures can drop below freezing or exceed 120° F. ™ • Ensure a Tuf Kote model is selected (Example: WX1-302TK) for outdoor installations. This proprietary coating is specifically designed to withstand outdoor applications. • Use wate

ページ6に含まれる内容の要旨

6. PLUMBING 1. Plumbing connections are similar to a traditional "tank WATER cross" or "tank tee". Provisions are made for popular CONNECTIONS line sizes via a 1-1/4" NPT male outer thread and a 1" NPT female inner thread. The plumbing connections are not directional and allow flow from either side. When attaching valves or fittings, uses the wrench flats provided. EXPLOSION HAZARD. Failure to follow these instructions can cause a rupture or explosion possibly causing serious or fatal

ページ7に含まれる内容の要旨

4. Connect the water line from the well pump to the inlet ™ of the Well-X1 . FROM WELL 5. Plumb the outgoing supply to the building's water supply system or into the water treatment equipment (if present). TO SYSTEM 6. Install a blow down tube from the relief valve to a drain RELIEF or to within 6" of the floor as required by local codes. VALVE A drip pan connected to an adequate drain must be installed if leaking or flooding could cause property damage. BLOWDOWN TUBE 6” 7

ページ8に含まれる内容の要旨

7. WIRING 1. Shut off the circuit breaker for the well system. Loosen the top screw housing cover. Flip the cover forward and remove to expose the control wires. Electrocution hazard. For your safety, the information in this manual must be followed to minimize the risk of electric shock, property damage or personal injury. Properly ground to conform with all governing codes and ordinances. 2. The 12 gauge wire leads are pre-stripped and ready to accept standard wire nuts. Each wire is

ページ9に含まれる内容の要旨

8. STARTUP & ADJUSTMENT 1. After plumbing and wiring are complete, close the service valve to allow startup without pressurizing TO the entire plumbing system. If a service valve was not SYSTEM installed, close all fixtures in the home. Ensure the bottom drain is closed. CLOSE SERVICE VALVE FROM WELL ™ 2. Restore power to the Well-X1 by turning on the breaker and electrical service switch (if installed). The display will illuminate. DISPLAY 3. The display will read "88" to test the display

ページ10に含まれる内容の要旨

8. STARTUP & ADJUSTMENT (con't) 5.The factory cut-out (pump off) setting is 60 psig. When ™ the pump reaches 60 psig, the Well-X1 will shut the pump off. Check the plumbing for leaks and repair before continuing. If during startup the cut-out setting of 60 psig cannot be reached, read the adjustment instructions to lower the cut-out within the pump's capability. OPEN SERVICE VALVE 6. Slowly open the service valve to allow the system to TO PRESSURIZE SYSTEM pressurize. The pressure may dro

ページ11に含まれる内容の要旨

PRESSURE ADJUSTMENT ™ The Well-X1 utilizes a simple cut-in/cut-out adjustment. Before setting the desired operating range, refer to the chart below to ensure the Well-X1's Maximum Acceptance is not exceeded. Adjust the precharge as shown on page 12. CAUTION! Exceeding Maximum Acceptance will reduce tank life and cause irreparable damage. Step 1: Find the Maximum Acceptance for the installed Step 2: Ensure the desired operating range does not ™ Well-X1 model. exceed that model's Maximum Accepta

ページ12に含まれる内容の要旨

3. To adjust the cut-out, depress MODE once and the PRESS AGAIN display will read HI. Again, press thetor s buttons TO SET to raise or lower the setting. The same 10-55 psig CUT-OUT differential range applies. Maximum setting is 80 psig. 4. After adjusting the cut-in and cut-out, release the buttons. After a slight pause, Pr will be displayed, indicating the settings are saved in the event of a power outage. PRECHARGE ADJUSTMENT Whenever the cut-in (LO) setting is changed, the tank prec

ページ13に含まれる内容の要旨

9. PUMP PROTECTION AND DIAGNOSTICS ™ The Well-X1 continually monitors pressure, cycle time and voltage to protect the well pump. The following error codes alert the user to a potential problem, prompting service. E1: Rapid Cycle E2: Low Suction (low water cut-off) E3: Voltage Protection E5: Improper Wiring ™ WELL-X1 ERROR CODES When an error occurs, the display will flash a diagnostic code and emit an audible chirp. ERROR CODE POSSIBLE CAUSES AND CONTROL ACTION Multiple cycles below a safe runt

ページ14に含まれる内容の要旨

10. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Alarm sounds 1. Error encountered 1. See Error Code section for possible causes. No water at fixtures 1. Error encountered 1. See Error Code section for possible causes. 2. No power 2. Check circuit breaker and wiring. 3. Water line obstructed 3. Ensure shut-off valves are open, check filtration equipment (if installed). 4. Faulty pump 4. Repair or replace as necessary. 5. Drain or relief valve open 5. Ensure valves are closed. 6. Leak in plum

ページ15に含まれる内容の要旨

11. REPLACEMENT PARTS 2 3 8 12 1 6 4 10 7 9 11 DESCRIPTION POSITION WX1-202 WX1-203 WX1-250 WX1-251 WX1-302 Replacement tank: Blue 1 144R273 146R825 145R379 145R380 150R92 Replacement tank: Tuf Kote™ 1 144R274 146R826 145R381 145R382 150R93 Electronic control (no cover) 2 146R2321 146R2321 146R2321 146R2321 146R2321 Control cover 3 146R2333 146R2333 146R2333 146R2333 146R2333 Mounting bracket 4 146R2336 146R2336 146R2336 146R2336 146R2336 Brass tee only (no accessories) 5 140R517 140R517 140R517

ページ16に含まれる内容の要旨

AMTROL INC. LIMITED PRODUCT WARRANTY Products covered: all Products manufactured by AMTROL Inc. (“AMTROL”). This warranty cannot be transferred – it is extended only to the original Purchaser or First User of the Product. By accepting and keeping this Product you agree to all of the warranty terms and limitations of liability described below. IMPORTANT WARNING – READ CAREFULLY THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL (“MANUAL”) to avoid serious personal injury and/or pr


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Amtrol WELL-X-TROL 取扱説明書 水道システム 25
2 Amtrol WELL-X-TROL WX-401 取扱説明書 水道システム 2
3 Amtrol VALUE-WELL 100 PSIG 取扱説明書 水道システム 27
4 Amtrol WELL-X-TROL 420 取扱説明書 水道システム 7
5 Sony 7 取扱説明書 水道システム 0
6 3Com ENTERPRISE OS 11.3 取扱説明書 水道システム 0
7 Acronis VIA C7-M 取扱説明書 水道システム 0
8 Acronis 200 Series 取扱説明書 水道システム 2
9 Acronis Z540 取扱説明書 水道システム 1
10 Alto-Shaam CombiGuard FI-23014 取扱説明書 水道システム 1
11 Adobe version cue CS3 取扱説明書 水道システム 2
12 Aiphone GF-NS 取扱説明書 水道システム 0
13 Alto-Shaam FI-28727 取扱説明書 水道システム 0
14 AMC FM DWS 1500 取扱説明書 水道システム 2
15 Amtrol WELL-X-TROL 取扱説明書 水道システム 25