ページ1に含まれる内容の要旨
S3.25
Leg Press Option
Assembly Instructions
ページ2に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions • Never drop or insert objects into any opening Obtaining Service Important Safety Instructions in the equipment. Keep hands away from moving Do not attempt to service the Leg Press Before beginning any fitness program, you should parts. Option yourself. This unit does not contain obtain a complete physical examination from your • Always check the unit and its cables before any user-serviceable parts. physician. each use. Make sure that all fasteners
ページ3に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions Table of Contents Important Safety Instructions............................................................... 2 Personal Safety During Assembly .................................................................................. 2 Obtaining Service .......................................................................................................... 2 Before You Begin .................................................................................
ページ4に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 1 Before You Begin Thank you for purchasing the Leg Press Option for your Precor equipment. This option will add a new dimension to your strength-training regimen. For proper installation, please read this guide thoroughly and follow the assembly instructions. Unpacking the Equipment The Leg Press Option is carefully tested and inspected before shipment. Precor ships the unit in several pieces that require assembly. Two people are required to assemble
ページ5に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions Installation Requirements Assembly Tips • A 6-inch scale is provided at the bottom of every Follow these installation requirements when assembly instruction page. Use this scale to identify assembling the unit: the correct size bolts and spacers. The head of a • Fill out and mail the limited warranty card. bolt is not used in measuring the length of a bolt. The warranty card is found on the back cover of To find out the length of a particular bolt, me
ページ6に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions Assembly 3 Instructions Assembly of the Leg Press Option takes professional installers about 1 hour to complete. If this is the first time you have assembled this type of equipment, plan on significantly more time. Professional installers are highly recommended! CAUTION: Obtain assistance! Do not attempt to assemble the Leg Press Option by yourself. Because of the weight and size of the Leg Press Option, you could be injured or damage the equipment. R
ページ7に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 1. Remove the Shroud Important: For ease of assembly, the fasteners and Top Beam hardware for each step are labeled and packaged in separate bags. Note: If you are assembling the Leg Press Option along with your S3.25, go directly to Step 2. Before you can attach the Leg Press Option to the unit, you must remove the Shroud. Notch in Shroud fits A. Remove the Shroud by loosening and removing around Top Beam fastener six 2¾-inch bolts six washers six lo
ページ8に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 2. Attach the Cross Brace to the S3.25 Note: If you are assembling the Leg Press Option along with the S3.25, you should complete Step 10 in the S3.25 Assembly and Maintenance Guide before attaching the Cross Brace. A. Align the Cross Brace to the S3.25 Rear Upright and secure it using two 3-inch bolts four washers two locknuts Wrench tighten. 2 - 3" bolts Cross Brace 4 - washers A 2 - locknuts 1 2 3 4 5 6 Step 2. Attach the Cross Brace to the S3.25 p
ページ9に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 3. Assemble the Frame A. With someone helping you, lift the Seat Frame upright. Have your assistant hold it in place while you attach the Cross Brace in the next step. Backpad Support B. Attach the Cross Brace to the holes found at the front of the Seat Frame using Backpad Support two 3-inch bolts four washers Pop Pin two locknuts C Wrench tighten. Important: A label on the Seat Frame indicates the Have an assistant hold the Seat Frame stable mounting
ページ10に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions D. Assemble the Footrest by resting the Pivot Arm on the Rubber Bumper. Make sure that the red 2 - large ½" x 3¼" bolts arrow on the back of the Footrest points toward 4 - ½" diameter washers E 2 - large ½" lock nuts the ceiling. E. Attach the Footrest to the Pivot Arm and Pivot Tube using two large ½-inch by 3-¼-inch bolts 2 - 3" bolts four ½-inch-diameter washers 4 - washers F two large ½-inch locknuts 2 - locknuts Wrench tighten enough to allow fre
ページ11に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 4. Assemble the Seat Pads Lift the Pop A. Attach one of the Seat Pads to the Seat Bracket Seat Bracket Support Pin to slide B Support using the back rest two 1¼-inch bolts Seat Pad two washers used as a Wrench tighten. back rest B. Lift the Pop Pin and slide the Seat Pad out of the way to assemble the other Seat Pad. C. Attach the remaining Seat Pad to the Seat Frame using Handle two 3-inch bolts two washers 2 - 1¼" bolts Wrench tighten. 2 - washers A
ページ12に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 5. Route the Cable Push the Pivot C As you route the Cable through the pulleys on the Leg Arm forward Pivot Arm Press Option, wrench tighten the fasteners on each pulley as you go. Make sure that the Cable slides freely along the pulley (and beneath the cable retainer). Make sure that you are using the correct Cable before you tighten the fasteners. A. Attach the barrel end of Cable 40538-101 to the 1 - 4" bolt Seat Frame using 1 - washer A Seat Frame
ページ13に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 6. Assemble the Cable and Pulleys Rear Upright You can identify Cables by the white numbers placed at the end of the Cable. A. Place Leg Press Option Cable 40538-101 between a Attach this cable retainer and one 3½-inch pulley. Attach the end to the pulley to the Lower Pulley Bracket located at the Cable Tree base of the Rear Upright using Cable 40538-101 one 2-inch bolt two washers This end is one locknut 3½" Pulley attached to the Wrench tighten. Leg
ページ14に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions C. Reattach the end of the original Surgical Tube from the Cable Tree to its prior location and place the new Surgical Tube that came with the Leg Press Option to the outside of the Top Beam using 1 - 4" bolt one 4-inch bolt 2 - washers C 2 - ½" barrel spacers two washers 1 - locknut two ½-inch barrel spacers New Surgical one locknut Tube Wrench tighten. D. Place the ball-end of Leg Press Option Cable 40538- 1 - 1¼" button head bolt 101 up through the
ページ15に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 7. Replace the Shroud A. Pick up the Shroud and fasteners from the location Top Beam where you left them in Step 4B. B. Replace the Shroud by realigning the mounting holes and inserting six 2¾-inch bolts six washers six locknuts Wrench tighten. Notch in Shroud fits around Top Beam fastener Replace Shroud A 6 - 2¾" bolts 6 - washers B 6 - locknuts 1 2 3 4 5 6 Step 7. Replace the Shroud page 15
ページ16に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions A Top Cap Weight 4 Adjustments After the Leg Press Option is assembled, you should check the Cables for proper tension. These are some Top Weight obvious signs that cable problems exist: ✔ Excess slack exists in the Cable. ✔ The Top Cap Weight does not rest squarely on the Weight Pin Weight Stack. ✔ The Cable rubs the inside edges of the pulleys. CAUTION: Take the time to perform the following steps. If the Cables do not have the proper tension, you c
ページ17に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions Weight then further adjustments are needed. Continue with steps 2 and 3. 2. Rotate the Cam Washer A If the Top Cap Weight does not rest on the Top Weight, you must make further adjustments. Top Cap A. Remove excess tension from the Cable by placing Weight the Weight Pin into the Selector Stem just under the Top Cap Weight. B. To tighten or loosen the Cable tension, rotate the Cam Washer. Top Weight C. Look to see that Top Cap Weight rests squarely on
ページ18に含まれる内容の要旨
S3.25 Leg Press Option Assembly Instructions 3. Adjust the Rubber Bumper on Push the Pivot Arm up to adjust the Leg Press Option A the Rubber Bumper If the Top Cap Weight still does not rest on the Top Weight, you can make one final adjustment. A. If the Cable tension still needs adjusting, push the Pivot Arm up so that you can adjust the Rubber Bumper on the Leg Press Option. B. Rotate the Rubber Bumper up or down to tighten or loosen the Cable tension. Important: Tighten the locknut against th
ページ19に含まれる内容の要旨
Residential Equipment Limited Warranty Please fill out the Warranty Registration and Conditions Precor Incorporated warrants that all new Precor products are free of manufacturing defects in mail it to Precor. This warranty is valid only in accordance with the workmanship and materials. Parts repaired or replaced under the terms of this warranty will be conditions set forth below. warranted for the remainder of the original warranty period only. This warranty becomes effective 1. Warranty applie
ページ20に含まれる内容の要旨
Please fill out the Warranty Registration and S3.25 Leg Press Option Specifications mail it to Precor. Length: 60 inches (152 cm) Height: 33 inches (84 cm) Width: 30 inches (76 cm) ▼ Shipping weight: 125 lb (57 kg) Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Precor and Pacific Fitness are registered trademarks of Precor Incorporated. Specifications subject to change without notice. Copyright 2001 Precor Incorporated. Precor web site: www.precor.c
