ページ1に含まれる内容の要旨
AIR NAILER/STAPLER
2-IN-1 KIT
97525
Model
40115
ASSEMBLY and OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious inj
ページ2に含まれる内容の要旨
Specifications Air Inlet 1/4” - 18 NPT Recommended Air Pressure 60 - 100 PSI, 100 PSI Max. Magazine Capacity 100 Nails or 80 Staples Safety Feature Single Sequential Safety Trip Mechanism 5 1 Nail Size .039-.042” Shank (18 Gauge), / ” - 1- / ” L 8 4 1 1 1 Staple Size / ” Crown, .039-.042” Shank (18 Gauge), / ” - 1- / ” L 4 2 4 Accessories Oil Dropper, 2 Wrenches, 1 Coupler Plug Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltag
ページ3に含まれる内容の要旨
8. Use eye and ear protection. Always wear ANSI-approved impact safety goggles and appropriate hearing protection. Wear a full face shield if you are producing metal filings or wood chips. Wear a NIOSH-approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Other people in the work area must also wear ANSI-approved impact safety goggles. 9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubri
ページ4に含まれる内容の要旨
heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Check your air compressor’s manual for the appropriate size cord. It is also possible that the use of an extension cord may cause your circuit breaker to trip or your panel fuse to break. If this happens, either use the compressor without an extension cord or find a larger amperage circuit to use. 19. Maintenance. The maintenance outlined in the maintenance section should be perfo
ページ5に含まれる内容の要旨
Unpacking When unpacking, check to make sure the parts listed on page 9 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Operation 1/4”-18 NPT Nailer/ Stapler For best service you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. 1. You will need to prepare a 1/4”
ページ6に含まれる内容の要旨
Operation - Testing The Single Sequential Safety Trip Mechanism (continued) 3. Empty the magazine of nails or staples. 4. Check that the Trigger (38) and the Safety (42) on the nose of the tool, move freely, without sticking. 5. Connect the air supply to the tool at the Air Plug (77) and set at the recommended 60- 100 PSI, and not over the maximum 100 PSI. 6. Test the tool by depressing the Safety (42) on the nose of the tool against the workpiece without pulling the Trigger (38). The tool
ページ7に含まれる内容の要旨
Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer/Stapler from the air hose. 2. Empty Magazine A (61) completely. 3. Attempt to fire the Nailer/Stapler into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any staples. 4. Always leave Magazine A (61) open during maintenance. The Magazine is spring- loaded and may cause parts or a fastener to fly out of the Nailer/Stapler. Clearing Jams FIGURE 1 1. Disconnect
ページ8に含まれる内容の要旨
Anytime any maintenance or repairs are done, FIRST: 1. Disconnect the Nailer/Stapler from the air hose. 2. Empty Magazine A (61) completely. 3. Attempt to fire the Nailer/Stapler into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any staples. 4. Always leave Magazine A (61) open during maintenance. The Magazine is spring- loaded and may cause parts or a fastener to fly out of the Nailer/Stapler. Troubleshooting Guide Stop using the Nailer/Stapler immediate
ページ9に含まれる内容の要旨
Maintenance Warning! Always disconnect the tool from the air compressor and then empty the magazine of nails or staples before attempting to inspect or perform maintenance to the Nailer/ Stapler. 1. Inspect all of the nuts and screws and make sure they are securely fastened. 2. Periodically lubricate the driving mechanism and magazine with a light oil. Wipe down with a clean cloth. Never use gasoline or flammable solvents to clean the tool. 3. Inspect your air compressor according to manufa
ページ10に含まれる内容の要旨
Assembly Drawing NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 97525 For technical questions, please call 1-800-444-3353. 40115 Page 10
ページ11に含まれる内容の要旨
LIMITED 1 YEAR WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment). This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repair
