Summary of the content on the page No. 1
EXS 9950 6th 99.9.24 5:31 PM Page 1
Summary of the content on the page No. 2
EXS 9950 6th 99.9.24 5:31 PM Page 2 Introduction Thank you for choosing the Uniden EXS 9950 cordless telephone. This phone is designed for reliability, long life, and outstanding performance utilizing the latest in 900 MHz Spread Spectrum technology. Note: Some illustrations in this manual may differ from the actual unit for explanation purposes. Features • 900 MHz Spread Spectrum Technology • Stand Alone Telephone Answering Device (STAD) • 20 Enhanced Memory Dial Location • 4 One-touch Memo
Summary of the content on the page No. 3
EXS 9950 6th 99.9.24 5:31 PM Page 3 Controls and functions 1 2 5 6 talk batt DIGITAL SPREAD SPECTRUM 12 vol 7 talk flash 13 8 mute mem rdl/p 14 9 abc def 12 3 15 ghi jkl mno 45 6 pqrs tuv wxyz 78 9 tone0# oper 10 3 16 m1 m2 m3 m4 11 4 17 19 DIGITAL SPREAD SPECTRUM 20 21 speaker 22 34 23 volume open 35 backup battery 24 status 36 25 delete play/stop 37 26 repeat greeting voice memo skip 38 27 answer on/off pin clock page 39 28 mic 18 29 30 31 32 33
Summary of the content on the page No. 4
EXS 9950 6th 99.9.24 5:31 PM Page 4 1. Handset antenna 18. Base microphone 2. Headset jack cover 19. Base speaker 3. Handset battery compartment 20. Speaker key 4. Ringer on/off switch 21. Handset retainer clip 5. Handset speaker 22. Speaker LED 6. Talk/Batt LED 23. Volume down key 7. Talk key 24. Status LED 8. Volume down key 25. Spare battery compartment 9. Mute key 26. Delete key 10. Tone key 27. Repeat key 11. Handset microphone 28. Greeting key 12. Volume up key 29. Base charge contacts 1
Summary of the content on the page No. 5
EXS 9950 6th 99.9.24 5:31 PM Page 5 Getting Started Contents Introduction / Features...............inside front cover Controls and Functions ..............inside front cover Basics Getting Started Read this first..........................................................3 Step 1: Checking the package contents...............4 Step 2: Setting up the base unit ...........................5 Mounting the base unit on a wall ...........8 Memory Dialing Step 3: Installing the handset battery pack......
Summary of the content on the page No. 6
open backup battery EXS 9950 6th 99.9.24 5:31 PM Page 6 Read this first This cordless telephone must be set up before use. Follow these steps; Step 1 (page 4) Unpack and check the telephone and accessories. Step 2 (page 5 to 9) Next, choose the best location to set up the base unit. Base unit Step 3 (page 10 to12) Then, insert the battery pack into the handset. You have to charge the battery pack for more than 17 hours before using the phone. Handset About the digital security code This cordl
Summary of the content on the page No. 7
backup battery open EXS 9950 6th 99.9.24 5:31 PM Page 7 Checking the package contents Make sure you have received the following items in the package. If any of these items are missing or damaged, contact the Uniden Parts Department (see below). • Base unit • Handset • AC adapter (AD-9500) • Rechargeable • Telephone line • Wall mount adapter battery pack cord (Long, Short) (BT-999) • Beltclip • Memo sticker • This Owner's Manual • Precautions and Important Safety Instructions • Registration Ca
Summary of the content on the page No. 8
EXS 9950 6th 99.9.24 5:31 PM Page 8 Setting up the base Do the following steps. • Choose the best location • Connect the base unit • Choose the dialing mode Choose the best location Before choosing a location for your new phone, read the INSTALLATION CONSIDERATIONS included in the PRECAUTIONS AND IMPORTANT SAFETY INSTRUCTIONS brochure. Here are some important guidelines you should consider: Avoid heat sources, such as Avoid noise sources such as a window radiators, air ducts, and sunlight by
Summary of the content on the page No. 9
open backup battery EXS 9950 6th 99.9.24 5:31 PM Page 9 Connect the base unit If you want to install the base unit on the wall, see page 8. Route the cord. Place the power cord so it 2 does not create a trip To AC outlet hazard, or where it could become chafed and create a fire or electrical hazard. To DC IN 10V AC adapter (supplied) 1 To telephone outlet To TEL LINE Telephone line cord (supplied) 1 Connect the telephone line cord to the TEL LINE jack and to a telephone outlet. 2 Connect the A
Summary of the content on the page No. 10
EXS 9950 6th 99.9.24 5:31 PM Page 10 Use only the supplied AD-9500 AC adapter. Do not use any other Polarity of the plug AC adapter. Connect the AC adapter to a continuous power supply. Place the base unit close to the AC outlet so that you can unplug the AC adapter easily. Modular If your telephone outlet isn't modular, contact your telephone company for assistance. Choose the dialing mode PULSE TONE Depending on your dialing system, set the PULSE-TONE switch as follows: If your dialing sy
Summary of the content on the page No. 11
EXS 9950 6th 99.9.24 5:31 PM Page 11 Mounting the base unit on a wall Standard wall plate mounting This phone can be mounted on any standard telephone wall plate. 1 Snap the wall mount 1 adapter into the notches on the base. 2 Plug the telephone line cord to the TEL LINE jack and the AC adapter to the DC IN 10V jack. 3 Plug the telephone line cord into the telephone outlet. 4 Wrap the AC adapter 2 - 7 cord inside the 6 molded wiring 2 channel. Then wrap the cord around the strain relief notc
Summary of the content on the page No. 12
EXS 9950 6th 99.9.24 5:31 PM Page 12 8 On the base unit, pull the Handset retainer handset retainer out of the slot. Rotate it clockwise 180 degrees. 9 Flip the retainer from front to If you have wall mounted the base, you must remove back. Slide it back into the slot the beltclip to charge the so that the lip of the retainer is handset facing forward. up and the oval is down. The retainer holds the handset in place. Direct wall plate mounting If you don't have a standard wall plate, you can
Summary of the content on the page No. 13
open backup battery EXS 9950 6th 99.9.24 5:31 PM Page 13 Installing the handset battery pack Charge the battery pack for more than 17 hours before you start using your phone. 1 Press in on the battery cover release and slide the cover down until it comes off. 2 Install the nickel-cadmium battery with the label facing down. Label face 3 Slide the battery cover on until it snaps into place. 4 Place the handset on the base. 5 Make sure that the “status” LED lights. If the LED doesn’t light, check
Summary of the content on the page No. 14
open backup battery EXS 9950 6th 99.9.24 5:31 PM Page 14 Battery use time (per charge) From fully charged • Four hours coutinuous use. • Seven days when the handset is in the standby mode. When the battery charge becomes low Even when the battery When the voltage of battery pack in the handset is very low and pack is not being used, it needs to be charged, the phone is programmed to eliminate will gradually discharge functions in order to save power. If the battery charge becomes over a long p
Summary of the content on the page No. 15
EXS 9950 6th 99.9.24 5:31 PM Page 15 Automatic digital code security To prevent other parties from making unauthorized calls on your phone line, a digital code was added to the EXS 9950. Your phone’s handset and base share this code, which is randomly set each time you place the handset on the base. 12
Summary of the content on the page No. 16
EXS 9950 6th 99.9.24 5:31 PM Page 16 Making a call talk 1 Press . The talk/batt LED lights. 2 Dial the phone number. talk 3 To hang up, press or return the handset to the base. The phone number can be up to 32 digits. If the talk/batt LED never stop flashing, place the handset on the base for at least three seconds and make a call again. Other Operations To Do this ¥
»
To adjust the ear speaker volume Press or during the call. To temporarily switch to tone dial P
Summary of the content on the page No. 17
open backup battery EXS 9950 6th 99.9.24 5:31 PM Page 17 Receiving a call From the handset Handset on the base 1 Phone rings. The talk/batt LED flashes. 2 Pick up the handset and begin speaking. talk 3 To hang up, press or return the handset to the base. Handset off the base 1 Phone rings. The talk/batt LED flashes. 2 Press and begin speaking. talk 3 To hang up, press or retur talk n the handset to the base. From the base 1 The phone rings. The status LED on the base f
Summary of the content on the page No. 18
ringer off on ringer off on EXS 9950 6th 99.9.24 5:31 PM Page 18 Flash and Call Waiting If you have “Call Waiting” service and a call waiting tone sounds while you are on a call, press to accept the waiting call. flash flash There is a short pause, then you will hear the new caller. To return to the original caller, press again. flash Adjusting the ringer and earpiece volume Handset ringer tone The phone has four types of ringer tone. ¥
flash In the standby mode, press
Summary of the content on the page No. 19
open backup battery EXS 9950 6th 99.9.24 5:31 PM Page 19 Base speaker volume To control the speaker volume of the volume ¥
base, adjust the and volume »
button as desired. Redialing a call The last phone number dialed can be quickly redialed. 1 Press . The talk talk/batt LED lights. 2 Press . rdl/p If the recently dialed number exceeds 32 digits, 3 To hang up, press or place the talk only the first 32 digits are handset on the base. retained for redialing. Mute You
Summary of the content on the page No. 20
EXS 9950 6th 99.9.24 5:32 PM Page 20 Storing phone numbers Your EXS 9950 stores up to 24 numbers in handset (20 memory dials and 4 one-touch memory dials). mem 1 Press while in standby mode. The talk/batt LED flashes. 2 Dial the number you wish to store (up to 16 digits). You must press a key within 30 seconds or the mem 3 Press again. phone will return to standby. If you return the 4 Enter a two-digit number (01 - 20) or handset in the cradle, the press One-touch memory key
