Summary of the content on the page No. 1
EXS 9910 5th 99.9.24 5:00 PM Page 1
Summary of the content on the page No. 2
EXS 9910 5th 99.9.24 5:00 PM Page 2 Introduction Thank you for choosing the Uniden EXS 9910 cordless telephone. This phone is designed for reliability, long life, and outstanding performance utilizing the latest in 900 MHz Spread Spectrum technology. Note: Some illustrations in this manual may differ from the actual unit for explanation purposes. Features • 900 MHz Digital Spread Spectrum Technology • 24 Enhanced Memory Dial Location • 32 Digit Redial • 2nd Battery Capability • Backup Power
Summary of the content on the page No. 3
EXS 9910 5th 99.9.24 5:00 PM Page 3 Controls and functions 1 2 5 6 talk batt DIGITAL SPREAD SPECTRUM 12 vol 7 talk flash 13 8 mute mem rdl/p 14 9 abc def 12 3 15 ghi jkl mno 45 6 pqrs tuv wxyz 78 9 oper tone0# 10 3 16 m1 m2 m3 m4 11 4 17 DIGITAL 900MHz SPREAD SPECTRAM 18 21 22 status open backup battery power 23 19 page/find 20 24
Summary of the content on the page No. 4
EXS 9910 5th 99.9.24 5:00 PM Page 4 1. Handset antenna 18. Handset retainer clip 2. Headset jack cover 19. Spare battery charge compartment 3. Handset battery compartment 20. Base charging contacts 4. Handset ring switch 21. Base antenna 5. Handset speaker 22. Status LED 6. Talk/Batt LED 23. Power LED 7. Talk key 24. Page/Find key 8. Volume down key 25. Pulse-Tone switch 9. Mute key 26. DC power input 10. Tone key 27. Phone jack 11. Handset microphone 12. Volume up key 13. Flash key 14. Redial
Summary of the content on the page No. 5
EXS 9910 5th 99.9.24 5:00 PM Page 5 Getting Started Contents Introduction / Features...............inside front cover Controls and Functions ..............inside front cover Getting Started Basics Read this first..........................................................3 Step 1: Checking the package contents...............4 Step 2: Setting up the base unit ...........................5 Mounting the base unit on a wall ...........8 Step 3: Installing the handset battery pack........10 Charging o
Summary of the content on the page No. 6
900MHz DIGITAL SPECTRAM SPREAD status power open backup battery page/find EXS 9910 5th 99.9.24 5:00 PM Page 6 Read this first This cordless telephone must be set up before use. Follow these steps; Step 1 (page 4) Unpack and check the telephone and accessories. Step 2 (page 5 to 9) Next, choose the best location to set up the base unit. Base unit Step 3 (page 10 to12) Then, insert the battery pack into the handset. You must charge the battery pack for more than 16 hours before using the phone.
Summary of the content on the page No. 7
900MHz DIGITAL SPREAD SPECTRAM status power open backup battery page/find EXS 9910 5th 99.9.24 5:00 PM Page 7 Checking the package contents Make sure you have received the following items in the package. If any of these items are missing or damaged, contact the Uniden Parts Department (see below). • Base unit • Handset • AC adapter (AD-420) • Rechargeable • Telephone line • Wall mount adapter battery pack cord (2) (BT-999) • Memo sticker (2) • Beltclip • This Owner's Manual • Precautions and
Summary of the content on the page No. 8
EXS 9910 5th 99.9.24 5:00 PM Page 8 Setting up the base unit Do the following steps. • Choose the best location • Connect the base unit • Choose the dialing mode Choose the best location Before choosing a location for your new phone, read the INSTALLATION CONSIDERATIONS included in the PRECAUTIONS AND IMPORTANT SAFETY INSTRUCTIONS brochure. Here are some important guidelines you should consider: Avoid heat sources, such as Avoid noise sources such as a window radiators, air ducts, and sunligh
Summary of the content on the page No. 9
900MHz DIGITAL SPREAD SPECTRAM status message open backup battery page/find EXS 9910 5th 99.9.24 5:00 PM Page 9 Connect the base unit If you want to install the base unit on the wall, see page 8. Route the cord. Place the power cord so it 2 does not create a trip To AC outlet hazard, or where it could become chafed and create a fire or electrical hazard. To DC IN 9V AC adapter 1 (supplied) To telephone outlet To TEL LINE Telephone line cord (supplied) 1 Connect the telephone line cord to the T
Summary of the content on the page No. 10
EXS 9910 5th 99.9.24 5:00 PM Page 10 Use only the supplied AD-420 AC adapter. Do not use any other AC Polarity of the plug adapter. Connect the AC adapter to a continuous power supply. Place the base unit close to the AC outlet so that you can unplug the AC adapter easily. Modular If your telephone outlet isn't modular, contact your telephone company for assistance. Choose the dialing mode PULSE TONE Depending on your dialing system, set the PULSE-TONE switch as follows: If your dialing syste
Summary of the content on the page No. 11
EXS 9910 5th 99.9.24 5:00 PM Page 11 Mounting the base unit on a wall Standard wall plate mounting This phone can be mounted on any standard telephone wall plate. 1 Snap the wall mount 1 adapter into the notches on the base. 2 Plug the telephone line cord to the TEL LINE jack and the AC adapter to the DC IN 9V jack. 3 Plug the telephone line cord into the telephone outlet. 4 Wrap the AC adapter 2 - 7 cord inside the molded wiring 6 channel. Then wrap 2 the cord around the strain relief notch
Summary of the content on the page No. 12
900MHz DIGITAL SPREAD SPECTRAM EXS 9910 5th 99.9.24 5:00 PM Page 12 8 On the base unit, pull the Handset retainer handset retainer out of the slot. Rotate it clockwise 180 degrees. 9 Flip the retainer from front to back. Slide it back into the slot so that the lip of the retainer is If the handset beltclip is up and the oval is down. The attached, you cannot retainer holds the handset charge the handset facing in place. forward when the phone is mounted on the wall (See page 21). Direct wall
Summary of the content on the page No. 13
900MHz SPREAD DIGITAL SPECTRAM status power open backup battery page/find EXS 9910 5th 99.9.24 5:00 PM Page 13 Installing the handset battery pack Charge the battery pack for more than 16 hours before you start using your phone. 1 Press in on the battery cover release and slide the cover down until it comes off. 2 Install the nickel-cadmium battery with the label facing down. Label face 3 Slide the battery cover on until it snaps into place. 4 Place the handset on the base. 5 Make sure that th
Summary of the content on the page No. 14
status power page/find status power page/find open backup battery EXS 9910 5th 99.9.24 5:00 PM Page 14 Battery use time (per charge) From fully charged • Four hours coutinuous use. • Seven days when the handset is in the standby mode. Even when the battery pack is not being used, it When the battery charge becomes low will gradually discharge When the voltage of battery pack in the handset is very low and over a long period. For needs to be charged, the phone is programmed to eliminate optimum
Summary of the content on the page No. 15
EXS 9910 5th 99.9.24 5:00 PM Page 15 Automatic digital code security To prevent other parties from making unauthorized calls on your phone line, a digital code was added to the EXS 9910. Your phone’s handset and base share this code, which is randomly set each time you place the handset on the base. 12
Summary of the content on the page No. 16
EXS 9910 5th 99.9.24 5:00 PM Page 16 Making a call talk 1 Press . The talk/batt LED lights. 2 Dial the phone number. 3 To hang up, press or retur talk n the handset to the base. If the talk/batt LED never stops flashing, place the handset on the base for at least five seconds and make a call again. Other Operations To Do this ¥
To adjust the ear speaker volume Press or during the call. »
/tone To temporarily switch to tone dial Press . The following *
Summary of the content on the page No. 17
EXS 9910 5th 99.9.24 5:00 PM Page 17 Receiving a call Handset on the base 1 Phone rings. The talk/batt LED flashes. When you receive a call 2 Pick up the handset and begin during a page or memory speaking. storing, pressing only the talk key connects a 3 To hang up, press or retur talk n call. the handset to the base. Handset off the base 1 Phone rings. The talk/batt LED flashes. 2 Press or any key and begin talk speaking. 3 To hang up, press or retur talk n the handset
Summary of the content on the page No. 18
ringer off on ringer off on EXS 9910 5th 99.9.24 5:00 PM Page 18 Flash and Call Waiting If you have “Call Waiting” service and a call waiting tone sounds while you are on a call, press to accept the waiting call. flash There is a short pause, then you will hear flash the new caller. To return to the original caller, press again. flash Adjusting the ringer and earpiece volume Ringer tone The phone has four types of ringer tone. ¥
flash In standby mode, press and f
Summary of the content on the page No. 19
EXS 9910 5th 99.9.24 5:00 PM Page 19 Redialing a call The last phone number dialed can be quickly redialed. 1 Press . The talk talk/batt LED lights. 2 Press . rdl/p If the recently dialed 3 Press or place the handset on talk number exceeds 32 digits, the base to hang up. only the first 32 digits are retained for redialing. Mute You can turn off the handset microphone so that the person you are talking with cannot hear you. 1 Press during a telephone call. mut
Summary of the content on the page No. 20
900MHz DIGITAL SPREAD SPECTRAM status power open backup battery page/find EXS 9910 5th 99.9.24 5:00 PM Page 20 Using page feature To locate the handset (while it’s off the page/find base), press on the base. The handset beeps for 15 seconds. If the handset was paged during a call, you can cancel it by pressing talk . 17
