Summary of the content on the page No. 1
1 HP CANISTER
DUST COLLECTOR
MODEL G0583
INSTRUCTION MANUAL
COPYRIGHT © JANUARY, 2005 BY GRIZZLY INDUSTRIAL, INC.; UPDATED SEPTEMBER, 2005.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#CR6902 PRINTED IN TAIWAN
Summary of the content on the page No. 2
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often yo
Summary of the content on the page No. 3
Table of Contents INTRODUCTION ............................................................................................................................... 2 Foreword .................................................................................................................................... 2 Contact Info ................................................................................................................................ 2 Identification ....................................
Summary of the content on the page No. 4
INTRODUCTION Foreword Contact Info If you have any comments or criticisms that Grizzly Industrial, Inc. is proud to offer the you feel we should address in our next printing, Model G0583 1 HP Canister Dust Collector. This please write to us at: machine is part of Grizzly’s growing family of fine machinery. When used according to the guide- Grizzly Industrial, Inc. lines stated in this manual, you can expect years C ⁄O Technical Documentation of trouble-free, enjoyable operation. P.O. Box
Summary of the content on the page No. 5
MACHINE DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL G0583 1 HP CANISTER DUST COLLECTOR Design Type ................................................................................. Single Stage Floor Model Overall Dimensions: 1 Base ..............................................................................................................15 ⁄4" x 26" 5 Height .....................................................................
Summary of the content on the page No. 6
Identification 1 2 7 5 3 4 6 1. Canister Filter Cleaning Handle 2. Canister Filter 3. 4" Duct Elbow 4. Clear Dust Storage Bag 5. Power Switch w/ Safety Key 6. Roller Base 7. Handle -4- G0583 1 HP Canister Dust Collector
Summary of the content on the page No. 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measure
Summary of the content on the page No. 8
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROP- 16. MAKE SURE GUARDS ARE IN PLACE ERLY SUPERVISED PERSONNEL TO AND WORK CORRECTLY BEFORE OPERATE MACHINERY. Make sure USING MACHINERY. operation instructions are safe and clearly understood. 17. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for 8. KEEP CHILDREN AND VISITORS AWAY. keys and adjusting wrenches before turn- Keep all children and visitors a safe dis- ing machinery ON. tance from the work area. 18
Summary of the content on the page No. 9
Additional Safety for Canister Dust Collectors 1. MACHINE USE. Do not use this dust col- 6. AVOIDING FIRES. Do not allow steel to lector to pick up liquids and metal scrap strike against impeller which may produce including, but not limited to, nails and fil- a spark. Sparks can smolder in wood dust ings. Metallic debris will contact the spin- for a long time before fire or flame is detect- ning impeller and could spark. The spark ed. If metal contacts metal during opera- could then cause
Summary of the content on the page No. 10
SECTION 2: CIRCUIT REQUIREMENTS Plug and Recepticle Requirements 110/220V Operation The motor is prewired to 110V and no plug replacement is required. For 220V connection, The Model G0583 features a single phase rewire the motor as in Figure 2, and install a 110V/220V 1 HP motor, which is prewired to NEMA 6-15 plug (Figure 1). You may also “hard- 110V. wire” the dust collector directly to your panel, pro- vided you place a disconnect near the machine. Amperage Draw Check the electrical cod
Summary of the content on the page No. 11
Extension Cords Grounding We do not recommend the use of extension cords with 220V equipment. Instead, arrange the place- Electrocution or a fire ment of your equipment and the installed wiring can result if the machine to eliminate the need for extension cords. Should is not grounded cor- the situation be necessary to use an extension, rectly. Make sure all make sure the cord is rated Standard Service electrical circuits are (grade S) or better. The extension cord must also grounded.
Summary of the content on the page No. 12
SECTION 3: SET UP Items Needed For This machine presents Set Up serious injury hazards to untrained users. Read through this entire man- Items Needed for Setup QTY ual to become familiar with the controls and Hex Wrench 3mm ...............................................1 operations BEFORE Wrench or Socket 12mm ....................................1 starting the machine! #2 Phillips Screwdriver .......................................1 Inventory Wear safety glasses dur- ing the entire set u
Summary of the content on the page No. 13
Box 2: Main Components (Figure 4) Site Considerations E. Elbow 4" ...................................................... 1 F. Base ............................................................ 1 Working Clearances G. Clear Dust Storage Bag ............................. 1 Consider existing and anticipated needs, size of H. Round Support ........................................... 1 material to be processed through each machine, I. Rectangle Supports .................................... 2 and s
Summary of the content on the page No. 14
Hardware Recognition Chart -12- G0583 1 HP Canister Dust Collector
Summary of the content on the page No. 15
Base and Supports 4. Place the round and rectangle supports on 5 5 Components and Hardware Needed: QTY the base and install with six ⁄16"-18 x ⁄16" hex Base ...................................................................1 bolts (see Figure 7). Casters ...............................................................4 Round Support ...................................................1 Rectangle Support ..............................................2 .........................................
Summary of the content on the page No. 16
Canister Filter 3. Install the handle onto the top of the canister and tighten the set screw against the flat of Components and Hardware Needed: QTY the shaft (Figure 10). Canister Filter .....................................................1 Handle ................................................................1 Metal Canister Clamp .........................................1 Narrow Foam Strip .............................................1 Tools Needed: Hex Wrench 3mm ........................
Summary of the content on the page No. 17
Collection Bag 3. Tighten the lower bag clamp around the wide foam strip to seal and secure the lower col- Components and Hardware Needed: QTY lection bag (Figure 13). Clear Collection Bag ...........................................1 Lower Bag Clamp ...............................................1 Wide Foam Strip .................................................1 To install the collection bag: 1. Secure the wide foam strip around the out- side bottom rim of the collector and trim the excess (F
Summary of the content on the page No. 18
SECTION 4: COLLECTION SYSTEM Material Selection General You have many choices regarding dust collection The Model G0583 is designed to be a single- ducting, but flexible hose is the most common. machine dust collector. Locate the dust collec- However, be aware that there is a fire or explo- tor where it will not interfere with the workpiece sion hazard if plastic duct material is used for being processed, and no more than 10' of duct- dust collection without being grounded against ing is
Summary of the content on the page No. 19
There are also many kinds of pure plastic flex- Duct Grounding ible hose, such as non-perforated drainage type hose and dryer vent hose. Drainage type hose, while being economical, does not quite have the Since plastic hose is abundant, relatively inex- flexibility required for dust collection. The inside pensive, easily assembled and air tight, it is a of the duct is also deeply corrugated and can very popular material for conveying dust from increase the static pressure loss by as much
Summary of the content on the page No. 20
Be sure that you extend the bare copper wire We also recommend wrapping the outside of all down all branches of the system. Do not forget plastic ducts with bare copper wire to ground the to connect the wires to each other with wire nuts outside of the system against static electrical when two branches meet at a “Y” or “T” connec- build up. Wire connections at Y’s and T’s should tion. be made with wire nuts. Ensure that the entire system is grounded. If Attach the bare ground wire to each st
