Summary of the content on the page No. 1
Connectivity Peripherals
Installation Guide
Point 510
Point 1600
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Connectivity Peripherals Installation Guide Point 510 Point 1600
Summary of the content on the page No. 4
Fujitsu Personal Systems, Inc. has made every effort to ensure the accuracy and completeness of this document. However, because ongoing development efforts are continually improving our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes herein. Point 510 and Point 1600 are trademarks of Fujitsu Personal Systems, Inc. The Fujitsu logo is a registered trademark of Fujitsu Ltd. All other products are trade
Summary of the content on the page No. 5
Agency Compliance FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
Summary of the content on the page No. 6
Summary of the content on the page No. 7
Table of Contents About This Guide .............................................................................................................................. vii Organization....................................................................................................................................................... vii Chapter 1 Introduction to Connectivity Peripherals .......................................................................................1-1 Cradle Module ..........
Summary of the content on the page No. 8
vi
Summary of the content on the page No. 9
About This Guide This guide provides installation instructions for connectivity peripherals compatible with Point 1600 and Point 510 pen tablet systems including the following: • Portable port expander • Port replicator* • High-connectivity cradle* •High-usage cradle* • Wall-mount cradle* • Charge-only cradle * These connectivity peripherals are available in locking and non-locking versions. Information given in this manual applies to both versions. Instructions given in this guide include p
Summary of the content on the page No. 10
viii About This Guide
Summary of the content on the page No. 11
Chapter 1 Introduction to Connectivity Peripherals Connectivity peripherals for the Point 510 and Point 1600 pen tablet systems are engineered using modular design principles. Each connectivity peripheral is assembled using components which may be used in different connectivity peripheral products. Components that make up connectivity peripherals are shipped unassembled. This chapter gives an introduction to each connectivity peripheral. Use this chapter to verify that the components compri
Summary of the content on the page No. 12
Table 1-2 shows what type of connectors are present on each connectivity peripheral product. Table 1-2. Connectors on Connectivity Peripherals Serial Port A ✔✔ ✔ Serial Port B ✔✔ ✔ † Mouse Port ✔✔ ✔ (on portable port expander) Keyboard ✔✔✔✔ Mouse Port ✔✔✔ (on cradle module) Parallel Port ✔✔ ✔ Floppy Drive Port ✔✔ ✔ Video Port ✔✔ ✔ DC Power Input ✔✔✔✔✔ * Although the wall-mount cradle includes a mouse port, the mouse port is not used in the wall-mount cradle. † The mouse port on the portab
Summary of the content on the page No. 13
Cradle Module 1 The cradle module is a central component in the following connectivity peripherals: • port replicator • high-usage cradle • high-connectivity cradle • wall-mount cradle The cradle module holds the pen tablet when it is inserted in these connectivity peripherals. Two types of cradle modules are available, a locking version (cradle module FMW26CR8), and a non-locking version (cradle module FMW26CR28). The non-locking version is not equipped with the tubular lock and cradle lat
Summary of the content on the page No. 14
Port Replicator 1 The port replicator provides the combined features of the portable port expander, plus additional keyboard and power connectors. The port replicator is assembled by installing the portable port expander in the cradle module. For assembly instructions, see “Assembling the Port Replicator” in Chapter 2 of this manual. Components Assembled Package + = Cradle Port Portable Port Module Expander Replicator (Note: Latch and spacer must be removed before assembly.) The port repl
Summary of the content on the page No. 15
High-Connectivity Cradle 1 The high-connectivity cradle provides all the connectivity of the port replicator and is designed for desk-top or counter-top installations where the cradle remains stationary. Locking versions are equipped with a tubular lock which allows you to lock the pen tablet into the cradle. The high-connectivity cradle is assembled using a cradle module, cradle base, and portable port expander. An AC adapter must also be installed in the cradle base if the cradle is to pro
Summary of the content on the page No. 16
Wall-Mount Cradle 1 The wall-mount cradle provides a folding keyboard tray and can be located in hallways or other wall areas to give mobile workers a convenient place to store the pen tablet, input data with a keyboard and connect the pen tablet to an external power source. Locking versions are equipped with a tubular lock which allows you to lock the pen tablet into the cradle. The wall-mount cradle is assembled using a cradle module, wall-mount base, and a keyboard. Components Assembled P
Summary of the content on the page No. 17
Chapter 2 Assembling and Installing Connectivity Peripherals This chapter describes the assembly and installation of connectivity peripherals. Portable Port Expander 2 The portable port expander can be used alone with the pen tablet or it can be installed in the cradle module as a component in other connectivity peripheral assemblies. The portable port expander is equipped with a latch mechanism and spacer to allow it to be attached directly to the pen tablet. For details on attaching the po
Summary of the content on the page No. 18
Connectors 2 Figure 2-2 shows the location of peripheral connectors on the portable port expander. Mouse Port Serial Port B Parallel Port Serial Port A Floppy Disk Video Port Drive Port Figure 2-2. Bottom View, Portable Port Expander Peripheral connectors on the portable port expander are described in Table 2-1. Table 2-1. Portable Port Expander Connectors Port Description Serial Port A This 9-pin D-sub male connector can be used to connect an external device with a serial interface such as
Summary of the content on the page No. 19
Assembling the Port Replicator 2 The port replicator is assembled using a cradle module and a portable port expander. The process of assembling the port replicator is outlined in the following: • Install the portable port expander in the cradle module. • Attach the rubber feet to the cradle module. • Attach the wire catch to the cradle module. (Required if using the port replicator with the folding desk stand.) Detailed procedures for these tasks are given in this section. Before you begin,
Summary of the content on the page No. 20
To install the portable port expander in the cradle module, 1. Insert the portable port expander through the bottom of the cradle module as shown in Figure 2-3. 2. Position the portable port expander so you can see the portable port expander screw holes through the two holes inside the cradle module. 3. Insert the two screws (provided with the portable port expander) as shown in Figure 2-3 and tighten until snug. Screws Cradle Module Tubular Lock Portable Port Expander Figure 2-3. Installing
