Summary of the content on the page No. 1
OWNER’S OPERATING MANUAL
CL-610 and CL-610LT
DLP™ Projectors
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Table of Contents Limited Warranty ............................................................................ 5 Safety Precautions ......................................................................... 8 Overview ......................................................................................... 9 Features .............................................................................................................. 9 Front / Top View ...................................................
Summary of the content on the page No. 4
Table of Contents (continued) ISF Calibration ..................................................................................................... 43 Lamp Replacement ........................................................................ 45 Troubleshooting .............................................................................. 47 RS-232 Setup .................................................................................. 49 Connecting RS-232 to the Projector .......................
Summary of the content on the page No. 5
TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup and care, you should enjoy many years of unparalleled video performance. This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents. WHAT I
Summary of the content on the page No. 6
RIGHTS, LIMITS AND EXCLUSIONS: Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequentia
Summary of the content on the page No. 7
ADDITIONAL INFORMATION: To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this Limited Warranty, please call or write: RUNCO INTERNATIONAL, INC. Attn: Customer Service Department 2900 Faber Street Union City, CA 94587 Ph: (510) 324-7777 Fax: (510) 324-9300 Toll Free: (800) 23-RUNCO RUNCO VIDEO PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Model Purchased Date Serial Numbe
Summary of the content on the page No. 8
Safety Precautions Thank you for your purchase of this quality Runco video projector! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNE
Summary of the content on the page No. 9
Overview TM • Native 16:9 Aspect Ratio, SuperOnyx DMD 1280 x 720p Features • High Contrast and Picture Quality 12-degree mirrors with dark metal process. • High Dynamic Range and Rich Gray-scale 6-segment, 5x color wheel with wide color space. • TIR (Total Internal Reflection) Prism High-performance light engine with Cat’s Eye optics. • Wide Variety of Inputs Support for various video formats, including Composite, S-Video, Component, DTV Y/PB/PR, DTV RGB HD and Computer signals. The HDTV inp
Summary of the content on the page No. 10
Overview Front / Top View 1. Exhaust Vent 4. Top IR Sensor 2. Focus Ring and Zoom Ring 5. Status LEDs Access See “Control Panel” on page 13. Adjust the focus and zoom of image. 6. Intake Vent 3. Runco Logo Can be rotated to match floor or 7. Front IR Sensor ceiling installation. See “Runco Logo” on page 14. 8. Projection Lens 10 Runco CL-610 Owner’s Operating Manual
Summary of the content on the page No. 11
Overview Rear / Bottom View 1. Connector Panel 6. Runco Logo See “Connector Panel” on page 14. Can be rotated to match floor or ceiling installation. 2. AC Power IN Socket See “Runco Logo” on page 14. 3. AC Power Switch 7. Lamp Module Cover Remove this cover when replacing 4. Cable Access Door the lamp. See “Lamp Replacement” Open to access connectors. on page 45. See “Connector Panel” on page 14. 8. Front / Rear Adjusters 5. Cable Opening Adjusts the height or projection Pass ca
Summary of the content on the page No. 12
Overview This page is intentionally left blank. 12 Runco CL-610 Owner’s Operating Manual
Summary of the content on the page No. 13
Controls and Functions Control Panel 1. FOCUS RING - Green when the power is turned Adjust the focus of the image on (operational mode). - Rotate the focus ring right or left to - Flashing Orange for the first 45 focus the image. seconds after power-up indicating that the lamp is warming up. 2. ZOOM RING - Flashing Green for 110 seconds Adjust the size of the image after the projector was powered off - Rotate right to enlarge the image. indicating that the lamp is cooling
Summary of the content on the page No. 14
Controls and Functions To access the connector panel, pull firmly Connector Panel on the cable access cover to open it. 1. S-Video (mini DIN 4-pin) Y/C (S-video) signal input 2. 12v Trigger (mini jack, diameter 5.5 mm outside, 2.5 mm inside) +12V output, active when the projector is turned on 3. Video (RCA Jack) Composite video signal input 4. Component (RCA Jacks) 480i Component (Y/CB/CR) video signal input 5. HDMI (High-Definition Multimedia Interface) Input Digital video signal input 6.
Summary of the content on the page No. 15
Controls and Functions LIGHT Remote Control Press to turn on the remote control back light. ON Press to turn on the projector. OFF Press to turn off the projector. LIGHT VID (Video) ON OFF Composite video signal input. VID S-VID COMP1 COMP2 S-VID (S-Video) S-Video signal input. RGBHD HDMI COMP1 (Component 1) Component Y/CB/CR input. INFO RVR COMP2 (Component 2) DTV Y/PB/PR signal input. ENTER RGBHD INFO EXIT MENU DTV RGBHV signal input. Displays active source and aspect ratio information. H
Summary of the content on the page No. 16
Controls and Functions CINEMA Remote Control Image in Letterbox mode is enlarged to a 16x9 image (continued) and the upper and lower portions are compressed. ANA (Anamorphic) For 16:9 DVDs. 4X3 (Standard 4:3) The input signal will be scaled to fit 4:3 display mode LIGHT in the center of the screen. ON OFF LBOX (Letterbox) VID S-VID COMP1 COMP2 Image in letterbox format is enlarged to fit 16:9 full screen display and the upper/ lower RGBHD HDMI portions are “blanked off.” VWIDE (VirtualW
Summary of the content on the page No. 17
Installation Push the battery cover and slide it off. Install the Remote Control two AAA batteries with the correct polarity and then replace the cover. Notes on Batteries • Make sure that the battery polarities are correct when installing the batteries. • Do not mix an old battery with a new one or different types of batteries. • If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage. Notes on Remote Control Operation • Make sure t
Summary of the content on the page No. 18
Installation Proper installation of your projector will ensure the quality of your display. Whether you Installation are installing a projector temporarily or permanently, you should take the following into Considerations account to ensure your projector performs optimally. Choose the installation type that best suits your needs: front or rear screen, floor mount Installation Type ➤ or inverted mount. Front Screen, Floor Mount Installation Advantages Considerations • Easy to set up • Shares
Summary of the content on the page No. 19
Installation Rear screen installations There are two basic types of rear screens: diffused and optical. A diffusion screen has a surface that spreads the light striking it. Purely diffused screens have a gain of less than 1. The main advantage of the diffused screen is its wide viewing angle, similar to that of a flat screen for front screen projection. This type of screen is suitable when a wide viewing angle is required but there is low ambient room lighting. Optical screens take light fro
Summary of the content on the page No. 20
��� ������������� Installation Ambient Light ➤ In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your images will be noticeably reduced if light directly strikes the screen, such as when a shaft of light from a window or floodlight falls on the image. Images may then appear washed out and less vibrant. Other considerations and tips that can help improve your installation: Other Considerations ➤ • Keep the ambient temperature constant and below 35°C (95
