Summary of the content on the page No. 1
USER’S MANUAL
DLC-2000HD
Projection System
Liquid Crystal Projector &
TM TM
Pixel-For-Pixel Controller with Vivix Technology
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Table of Contents Limited Warranty ................................................................................................ 1 Introduction ........................................................................................................ 3 Warnings and Safety Precautions .................................................................... 4 Warning .......................................................................................................... 5 Safety Tips ..............
Summary of the content on the page No. 4
Limited Warranty LIMITED WARRANTY Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup and care, you should enjoy many years of unparalleled video performance. Please read this consumer protection plan carefully and retain it with your other important documents. This is a LIMITED WARRANTY as defined by the U.S. Consumer Product Warranty and Federal Trade Co
Summary of the content on the page No. 5
EFFECTIVE WARRANTY DATE: This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date. IMPORTANT: WARRANTY REGISTRATION: Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified. TO OBTAIN SERVICE, CONTACT YOUR RUNCO DEALER: Repairs made under the terms
Summary of the content on the page No. 6
Introduction Congratulations on your purchase of the DLC-2000HD system! This system was designed to be a fully integrated system, which includes the DLC-2000HD Projector and the unique PFP™ Controller. This system is extremely easy to use, as all of the controls for the Projector have been integrated into the PFP Controller for ease of operation and control. Not only does the Controller control all aspects of the Projector, but it also performs all of the NTSC or PAL video scaling for the Projec
Summary of the content on the page No. 7
Warnings and Safety Precautions CAUTION: To turn off main power, be sure to remove the plugs from power outlets. The power outlet sock- et should be installed as near to the equipment as possible, and should be easily accessible. REMARQUE: Pour mettre l’appareil hors circut, s’assurer de retirer la fiche de la prise d’alimentation. La prise d’alimentation doit être installé aussi proche que possible de l’appareil et doit être facile d’ accès. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPO
Summary of the content on the page No. 8
WARNING This equipment has been tested and found to comply with the limits for a Class ‘B’ digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial envi- ronment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Installation Manual, may cause harmful interference to radio communications. Ope
Summary of the content on the page No. 9
Indicator Lights Top View The Projector has four lights which provide a status of the operation of the Projector. These are described below: Lamp Temp. Ready Standby warning warning Lamp warning: Lights up YELLOW when Ready: Lights GREEN when the Projector the lamp has reached its useable life is ready for use. expectancy (1500 hours). Standby: Lights when Projector is in the Temp warning: Flashes RED when the standby mode; dims when in operation. internal temperature is too high. Ensure that th
Summary of the content on the page No. 10
< r u e t n u t Front and Rear Panel Descriptions Front Panel 1 2 3 ratio < > ratio TM PIXEL FOR PIXEL 4 5 6 7 8 9 10 1. IR RECEIVER Receives the infrared signal from the remote control. 2. POWER BUTTON Turns the unit ON or OFF. The Main Power switch on the rear of the unit must be on first for this button to be active. 3. POWERINDICATOR When the PFP Controller is ON, this LED will illuminate GREEN. When the unit is OFF or in STANDBY, this LED
Summary of the content on the page No. 11
Rear Panel 1 5 CAUTION RUNCO INTERNATIONAL RISK OF ELECTRIC SHOCK ! HAYWARD, CA DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR MADE IN USA COMLINK OUT CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE CENTER. 12V FUSE AC 120V 60Hz, 15W WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE RGB VIDEO OUTPUT VIDEO INPUTS THIS APPLIANCE TO RAIN OR MOISTURE. RS-232 IN V H B G R HDTV/
Summary of the content on the page No. 12
T I U N P P Remote Control Description A. IR OUTPUT INDICATOR Illuminates when a button is pressed, indicating that an IR signal is being A B transmitted. B. POWER BUTTON Toggles the power on and off. For a discreet on or off command, you can PWR C use the direct access buttons (see 'J'). Note: When the main AC power G switch is first turned ON, the Controller will go through an initiation cycle for approximately 15 seconds. The Controller cannot be turned on or operated until the initialization
Summary of the content on the page No. 13
Menu Description and Navigation Menu Tree INPUT SELECT Standard Video: Composite > S-Video Component High Definition: Component Anamorphic RGB Standard 4:3 Letterbox ASPECT RATIO SELECT Main Menu Through the Main Menu, you can easily switch sources and Aspect Ratios. To select a source, you may either use the direct access buttons on the remote (pg. 9) or the Left/Right buttons on the remote or Front Panel (pgs. 7, 10). If you wish to select a source via the Main Menu, press MENU, highlight the
Summary of the content on the page No. 14
Specifications DLC-2000HD Projector: Projector Type: LCD Native Resolution: 1366 x 768 Lamp: 250W Metal Halide Inputs: RGB/Component Bandwidth: 180 Mhz (RGB) Power Requirements: 100-120 VAC, 200-240 VAC 50/60 Hz (export version) Current: 3.3A (100-120 VAC), 1.7A (200-240 VAC) Power Consumption: 360W Dimensions: Width: 16.310 in. (414 mm) Depth: 25.801 in. (655 mm) Height: 8.439 in. (214 mm) Weight: 56 lbs. (25.4 kg) Safety Regulations: Complies with FCC Class 'B', CE, C-Tick 11
Summary of the content on the page No. 15
Controller: Inputs: (1) Component, (1) S-Video, (1) Composite, (1) HDTV/Computer Input standards: NTSC/PAL/480p/720p/1080i/SVGA/XGA Output format: 1366 x 768 Bandwidth: Video inputs: 5.5 Mhz, HDTV/Computer: 100 Mhz Power Input: 120V (220V export model), 50/60 Hz Power Consumption: 15W Control Options: RS-232, Infrared, Front Panel Operating Environment: 41°-95°F (5°-35° C), 0-90% humidity, Non-condensing Dimensions: Width: 17.45 in. (443.23 mm) Depth: 16 in. (406.40 mm) Height: 3.5 in. (88.90
Summary of the content on the page No. 16
Summary of the content on the page No. 17
RUMA-006700 rev 11-03 . . . . . Runco International 2900 Faber Street Union City, CA 94587 ph (510) 324-7777 fax (510) 324-9300 www.runco.com
