Summary of the content on the page No. 1
PORTABLE DATA COLLECTION
-
0010 DOCUMENT NUMBER: 350600
PT600
TERMINAL
USER’S GUIDE
Summary of the content on the page No. 2
NOTICE The unit is equipped with a NiMH battery pack, however it may not be powered on due to putting in storage for a period of time. In the case of above situation C - DC adapter and recharge the NiMH about hours or put into cradle about hours - DC adapter before using the unit. for charging reference) chapter 2.4 (please refer to with 12V AC 2.5 14~16 battery pack happened, plug in an 9V A discharging of the battery by
Summary of the content on the page No. 3
Page Chapter 1 ................................ .......... 1 1.1 Technical Specification ................................ 2 1.2 Interface Ports ................................ ............. 8 1.3 Using the Keyboard ................................ ..... 9 1.4 Triggering Scanner Module .......................... 11 1.5 Applic ation Development Environment ........ 12 1.6 Optional Charging/Communication Cradle ... 1 3 Chapter 2 ................................ .
Summary of the content on the page No. 4
Introduction The PT600 Portable Data Terminal, referred as PDT hereafter, with integrated laser scanner or pen scanner is a , compact and lightweight hand - held data collection terminal with good reliability, flexibility an d maintainability. Its compact size and form makes it even fits in your packet. The PDT incorporates a DOS - based system and provides users a PC compatible environment to develop and use the device. This terminal is well suited for transportation, warehouse distr
Summary of the content on the page No. 5
SOFTWARE PROGRAMMING TOOLS C, Turbo C, Visual C) - - - 16 - .5MB SRAM - 26 alphanumeric rubber keys with one laser trigger 100x65 pixel graphic backlit LCD with selection between 12 - c olumn by 4 - line in 8x16 font and 16 - column by 8 - line in 6x8 font by menu setup or system BARCODE SYMBOLOGY - A/E, EAN - 8/13, Codabar, Code128, Code39, Code39 with full ASCII, ITF, China postal code, CAL AND ENVIRONMENT ° C ~ 50 ° C (32 ° F ~ 1
Summary of the content on the page No. 6
- connector, Support TX/RX, CTS/RTS, GND, up to 57.6Kbps Kbps ) One IR port, Support TX/RX, to 57.6 K bps Xon/Xoff or CTS/RTS - - - 5 AC/DC adapter @ 9 DOCKING STATION PT600 - - - AC/DC adapter @ 12 • MS - • - • - • contrast • - - 3 - off point. System resumes from the last turn Software adjustable beeper volume and LCD driven user configuration interface Menu discriminated ologies auto Reads all major bar cod
Summary of the content on the page No. 7
• - - • l • Scan rate • ± 65 ° • ± 55 ° • - P • o l u • • Scan rate 5 - • 45 ° ~ 135 ° • Diagram shown with a Built - in Integrated Laser scanner Skew Tolerance 55° 65° 55° 65° Right side view of PDT Top view of PDT - 4 - Label Label Barcode Barcode Scan Beam Scan Beam Pitch Angle Print Contrast Ratio 0.5 min Reading Angle /sec 200 cm 0.1mm(0.04inch) Dept of field 0.12mm(5mil) tion Res Scanner en on clip Integrated 60mA typ.@5V Power con
Summary of the content on the page No. 8
- 5 - diagram Depth of Field
Summary of the content on the page No. 9
- 6 -
Summary of the content on the page No. 10
Diagram shown with a clip - on pen scanner 45° 45° - 7 -
Summary of the content on the page No. 11
The PT600 has a RS232C serial port with miniature RJ10 connector, Communication by Infrared LED which on the left side of lower cabinet 1 DC9 V 2 TXD Output 3 4 N.C. 5 6 N.C. 1 10 7 CTS 8 RTS Output 9 N.C. 10 N.C. PDT. RS232 cable TELEPHONE LINE RS-232 PORT - 8 - MODEM SYSTEM COMPUTER MODEM ut/output devices to the The diagram below shows the way to connect inp Request to send Clear to send Input Ground Reference GND Receive d
Summary of the content on the page No. 12
The keypad of PT600 consists of 27 rubber keys, the key is used to switch on/off the unit and other 26 keys are used to control the unit and key in data. The use o f keyboard is categorized to th ree modes: , , and . All keys except key may produce a sound (tone) when pressed. Keys of upper four rows have - [ ] is off, pressing the l turn on the unit. On the other hand, when the unit is on it is needed to press Pressing the key sets the keyboard to Command ver p
Summary of the content on the page No. 13
Summary of the content on the page No. 14
Press [ALPHA] key to toggle between normal mode and alpha mode of keyboard. In alpha mode, the cursor is an underscore sign and the keyboard is available to i nput upper case letters. In alpha mode, every numeric key contains 3 characters individually. Pressing the key [è] and [ ç] to choose among three First press [ALPHA] to switch the system to alpha mode, the cursor type will be changed ç è The PT600 c an be used with a built - in i r - on pen scanner m
Summary of the content on the page No. 15
The system of PT600 provides DOS functions and device drivers for application development, including bar code decoding, keypad input, display output, serial input/output communication, real - - a - - Plus and DOS - based JobGen Pro program generation software. It can C, Borland C and Turbo C. Pro, JobGen Plus or created by a compiler is downloaded to the unit and - - - use and comprehensive termina l application developing environment. Through the use of JobGen Plus, user c
Summary of the content on the page No. 16
An optional charging/communication cradle (dock station), PT016, has been incorporated a quick charge circuit that th e NiMH battery pack about 2.5 hours . Regular charging time of the battery pack through DC power adapter is about 14~16 hours. The cradle also allows users to link - - point RS - 232 or multi - RS - 422 connection for data communication. The cradle with internal POINT-TO-POINT RS232 Connection SYSTEM MULTI-POINT RS422 Connection SYSTEM - 13 - COMPUTER RS422 int
Summary of the content on the page No. 17
The PDT is operated by a rechargeable NiMH battery pack with two AA size 1.2V 1500mAH capacity or two AA alkaline batteries for the main An onboard 3V 190mAH Lithium battery (CR2032) is used as the - - up RTC and RAM and puts the Lithium battery in standby state. When the main power source is removed or below t he level to back - up the RAM and RTC properly, the power circuit of the PT600 automatically switches to the Lithium battery for back up. It is recommended
Summary of the content on the page No. 18
When the main battery low condition occurs, the main battery can continue to supply power for about 10 ~ 30 minutes, however the unit Meanwhile the unit continues to back - up the data contents in RTC and WARNING ! enough capacity to back up the system, the LITHIUM BATTERY LOW the unit is powered on . In this situation you should upload your data from the PDT immediate ly and replace a new 1. 2. 3. 4. - 15 - Insert the new main battery packet:
Summary of the content on the page No. 19
f rom s battery change . b attery . e backup Y our d 1. Refer to the procedure in previous paragraph, un - screw the backup ** Make sure to back up your data in PDT before making the - 16 - replacement the lithium back up battery. 3. Put the battery cover back. 2. Insert a new battery into the holder with correct orientation. ttery. battery cover and as illustration above to remove the lithium ba Lithium Back up Battery first. ata : Not Lithium
Summary of the content on the page No. 20
When the PDT sh ows “Main battery low” or sign , the battery pack in PDT needs to be recharged. There are two ways to charge the Inner shell Outer shell Plug one end of an AC - 9VDC power adapter into the DC - jack of RS 232 cable and the other end into a wall outlet. The battery pack will be fully 14~16 Quick Charging with PT016 AC to 12V DC Negative(-) Transformer Connect power adapter to PT016 and insert PDT into the chamber of PT016. The battery of PDT can be fully charge
