Summary of the content on the page No. 1
GE
Security
GE-DS-82 and 82-PoE Ethernet
Managed Switch User Manual
P/N 1069182 • REV 1.0 • ISS 23FEB10
Summary of the content on the page No. 2
Copyright © 2010 GE Security, Inc. This document may not be copied in whole or in part or otherwise reproduced without prior written consent from GE Security, Inc., except where specifically permitted under US and international copyright law. Disclaimer The information in this document is subject to change without notice. GE Security, Inc. (“GE Security”) assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or othe
Summary of the content on the page No. 3
Content Chapter 1 Introduction 1 Package Contents 2 Product Description 2 Product Features 4 Product Specifications 7 Chapter 2 Installation 11 Hardware Description 11 Switch Installation 16 Chapter 3 Switch Management 23 Requirements 23 Management Access Overview 24 Web Browser Management 25 SNMP-Based Network Management 28 The Administration Console 28 Direct Access 29 Protocols 30 Chapter 4 Web-Based Management 33 About Web-based Managemen
Summary of the content on the page No. 4
Commands Level 143 Chapter 6 Command Line Interface 145 Operation Notice 145 System Commands 146 Switch Static Configuration 147 Trunk Configuration 152 VLAN Configuration 155 Misc Configuration 165 Administration Configuration 167 MAC limit 172 Port Mirroring Configuration 173 Quality of Service 174 MAC Address Configuration 177 STP/RSTP Commands 179 SNMP 184 IGMP 188 802.1x Protocol 190 Access Control List 194 Binding 199 Power over Et
Summary of the content on the page No. 5
Chapter 1 Introduction The GE Security GE-DS-82 and GE-DS-82-PoE are Ethernet Managed Switches with 8 10/100Mbps ports and 2 Gigabit TP/SFP fiber optical combo connective ability with robust layer 2 features. The description of these models is below: GE-DS-82 : 8-Port 10/100Base-TX + 2-Port Gigabit TP/SFP Combo Managed Switch GE-DS-82-PoE : 8-Port 10/100Base-TX + 2-Port Gigabit TP/SFP Managed PoE Switch GE-DS-82 and 82-PoE Ethernet Managed Switch User Manual 1
Summary of the content on the page No. 6
Chapter 1: Introduction Package Contents Open the Managed Switch box and carefully unpack it. The box should contain the following items: The Managed Switch x1 User’s manual CD x1 Installation Sheet x1 19” Rack mount accessory kit x1 Power cord x1 Rubber feet X4 RS-232 cable x1 If any of these items are missing or damaged, please contact your dealer immediately. Product Description High Performance Wire-Speed Switching The GE Security GE-DS-82 Series of Managed Switches offer
Summary of the content on the page No. 7
Chapter 1: Introduction Cost-effective solution with SNMP monitor for Network deployment Not only catering to the needs of easy WEB-based management but also the centralized SNMP application to monitor the status of Switch and traffic per port, GE Security releases the cost-effective Managed Switch. The key features are listed below: • WEB / SSL / Telnet / Console management • 802.1Q / Q-in-Q VLAN • Rapid Spanning Tree • IGMP Snooping • 802.1X Authentication / RADIUS • Access Co
Summary of the content on the page No. 8
Chapter 1: Introduction Power over Ethernet of GE-DS-82-PoE The PoE in-line power following the standard IEEE 802.3af makes the GE-DS-82-PoE able to power 8 PoE devices at a distance of up to 100 meters through the 4-pair Cat 5/5e UTP wire. How to Use this Manual This User Manual is structured as follows: Section Section Content INTRODUCTION Product description with features and specifications Explains the functions of the Managed Switch, and how to physically INSTALLATION install i
Summary of the content on the page No. 9
Chapter 1: Introduction GE-DS-82-PoE • 8-Port 10/100Base-TX RJ-45 with PoE Injector • 2 10/100/1000T TP combo interfaces • 2 mini-GBIC/SFP slots, shared with Port-9 and Port-10 • Reset button for system management • 1 RS-232 male DB9 console interface for basic Switch management and setup Layer 2 Features • Prevents packet loss Flow Control: • IEEE 802.3x PAUSE frame Flow Control for Full-Duplex mode • Back-Pressure Flow Control in Half-Duplex mode • High performance Store and Forwa
Summary of the content on the page No. 10
Chapter 1: Introduction • IEEE 802.1p Class of Service • IP TOS / DSCP code priority • Port Base priority • Strict priority and weighted round robin (WRR) CoS policies • Ingress/Egress Bandwidth control on each port Multicast • IGMP Snooping v1 and v2 • IGMP Snooping v2 fast leave • IGMP Query mode for Multicast Media application Security • IEEE 802.1x Port-Based network access control protocol • RADIUS users access authentication • L3 / L4 Access Control List (ACL) • Source IP-MAC
Summary of the content on the page No. 11
Chapter 1: Introduction Power over Ethernet (GE-DS-82-PoE Only) • Complies with IEEE 802.3af Power over Ethernet End-Span PSE • Up to 8 IEEE 802.3af devices can be powered • Supports PoE Power up to 15.4 Watts for each PoE port • Auto detect powered device (PD) • Circuit protection to prevent power interference between ports • Remote power feeding up to 100m • PoE Management • Total PoE power budget control • Per port PoE function enable/disable • PoE Port Power feeding priority • P
Summary of the content on the page No. 12
Chapter 1: Introduction Maximum Frame Size 9K Bytes Back pressure for Half-Duplex Flow Control IEEE 802.3x Pause Frame for Full-Duplex Power Power Link/Activity (Green) Link/Activity (Green) LED 10/100 LNK / ACT (Green) PoE In-Use (Amber) 1000 LNK / ACT (Green) 1000 LNK / ACT (Green) 10/100 LNK / ACT (Green) 10/100 LNK / ACT (Green) 13” x 6.10” x 1.71” / 330 x 155 x 13” x 6.10” x 1.71” / 330 x 155 x 43.5mm 43.5mm 330 Dimensions ( W x D x H) 1U height 1U height Weight 2.8 lbs /
Summary of the content on the page No. 13
Chapter 1: Introduction Static Port Trunk Link Aggregation IEEE 802.3ad LACP (Link Aggregation Control Protocol) Supports 13 groups of 8-Port trunk support 4 priority queue Traffic classification based on: Quality of Service • Port-Based priority • 802.1p priority, • IP DSCP/TOS field in IP Packet v1 and v2 IGMP Snooping 256 multicast groups and IGMP query Bandwidth Control Per port Ingress / Egress bandwidth control in steps of128Kbps RX / TX / Both Port Mirror 1 to 1 monitor
Summary of the content on the page No. 14
Chapter 1: Introduction Power Pin Assignment - 1/2(+), 3/6(-) PoE Power Budget - 180 Watts Max. number of Class2 PD 8 Max. number of Class 3 - 8 PD Standards Conformance Safety FCC Part 15 Class A, CE IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX/100BASE-FX IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000Base-T IEEE 802.3x Flow Control and Back pressure IEEE 802.1d Spanning tree protocol IEEE 802.1w Rapid spanning tree protocol IEEE 802.1p Class of service IEEE 802.1Q VLAN Ta
Summary of the content on the page No. 15
Chapter 2 Installation This section describes the hardware features and installation of the Managed Switch on the desktop or rack mount. For easier management and control of the Managed Switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Managed Switch, please read this chapter completely. Hardware Description Switch Front Panel The unit front panel p
Summary of the content on the page No. 16
Chapter 2: Installation Gigabit TP Interface Port-9, Port-10: 10/100/1000Base-T Copper, RJ-45 Twist-Pair: Up to 100 meters. Gigabit SFP Slots Port-9, Port-10: 1000Base-SX/LX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver module: From 550 meters (Multi-mode fiber), up to 10/30/50/70/120 kilometers (Single-mode fiber). Reset button At the left of front panel, the Reset button is designed to reboot the Managed Switch without turning the power off. The following table summarizes
Summary of the content on the page No. 17
Chapter 2: Installation • System LED Color Function PWR Green Lit: indicates there is power to the Switch • Per 10/100Base-T RJ-45 port LED Color Function Lit: indicates the link through that port is successfully established LNK/ACT Green Blink: indicates the Switch is actively sending or receiving data over that port • Per 10/100/1000Base-T port/SFP interfaces LED Color Function Lit: indicates the port is operating at 1000Mbps Off: indicates the port is operating at 10Mbp
Summary of the content on the page No. 18
Chapter 2: Installation • Per 10/100Base-TX, PoE interfaces (Port-1 to Port-8) LED Color Function Lit: indicates the link through that port is successfully established LNK/ACT Green Blink: indicates the Switch is actively sending or receiving data over that port Lit: indicates the port is providing 48VDC in-line power PoE In Use Orange Off: indicates the connected device is not a PoE Powered Device (PD) • Per 10/100/1000Base-T port/SFP interfaces LED Color Function Lit: in
Summary of the content on the page No. 19
Chapter 2: Installation Figure 4: GE-DS-82 and GE-DS-82-PoE Rear panels Console Port The console port is a DB9, RS-232 male serial port connector. It is an interface for connecting a terminal directly. The console port provides rich diagnostic information including IP Address setting, factory reset, port management, link status and system settings. Users can use the attached RS-232 cable in the package and connect to the console port on the device. After the connection, users can run
Summary of the content on the page No. 20
Chapter 2: Installation Switch Installation This section describes how to install the Managed Switch and connect it as necessary. Please read the following instructions, and perform the procedures in the listed order. Desktop/Shelf Installation NOTE: Refer to the environmental restrictions listed in the Product Specification when selecting a location for the Managed Switch. Step 1: Attach the rubber feet to the recessed areas on the bottom of the Managed Switch. Step 2: Place the M
