Summary of the content on the page No. 1
HONEYWELL
REMOTE UV SENSOR
for Professional Weather Station TE923W
TS704
USER MANUAL
Summary of the content on the page No. 2
Table of Contents Introduction 3 Standard Package Contents 3 Sensor unit 4 Before you begin 4 Installation 5 Mounting 6 Operation 6 Maintenance 7 Troubleshooting 8 PRECAUTIONS 8 Specifications 8 FCC STATEMENT 9 DECLARATION OF CONFORMITY 9 STANDARD WARRANTY INFORMATION 10 2
Summary of the content on the page No. 3
Introduction Thank you for selecting the Honeywell remote UV sensor TS704. This product is a part of the Professional Weather Station TE923W. It measures UV (ultraviolet light) levels and transmits data to a TE923WD (main display unit). Note: In order to display the ultraviolet light levels, you must own a main display unit (TE923WD) for the Professional Weather Station TE923W. In this package you will find: One Sensor Unit One U-Shaped Sensor holder One Circular Ground Stand On
Summary of the content on the page No. 4
Sensor unit A B G F C E D A. LED INDICATOR • Flashes once when the remote UV sensor transmits a reading to the main unit • Flashes twice when battery power is low B. BATTERY COMPARTMENT SCREW Holds battery compartment door in place C. U-SHAPED SENSOR HOLDER Holds UV sensor in upright position D. CURCULAR GROUND STAND Secures sensor in the sensor holder on the flat surface E. UV SENSOR LID Covers UV sensor and battery compartment F. BATTERY COMPARTMENT Holds two AA-size
Summary of the content on the page No. 5
• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power requirements). • Insert batteries before first use, matching the polarity in the battery compartment • During an initial setup, place the main unit close to the remote UV sensor. • After reception is established (the remote UV readings will appear on the main unit’s display), position the UV sensor and the main unit within the effective transmission range of 328 feet (100 meters). Ideally it sh
Summary of the content on the page No. 6
Mounting There are three different options available for mounting the UV sensor: ground stand, stake and wall mount. Ground: • Insert the U-shaped sensor holder round end into the circular ground stand opening, matching 2 round holes in the opening • Secure the sensor in a location with a maximum sun exposure throughout the day. Stake: • Snap the sharp stake end onto the metal bar and secure with the screws provided. • Insert the other end of the metal bar into the U-shaped sens
Summary of the content on the page No. 7
To access UV mode from the main unit press UP or DOWN until the UV icon on the display will flash. From the handheld remote control: Press . Viewing UV Statistics In UV Mode press the MEMORY button viewing either current UV intensity, daily Maximum UV intensity with “DAILY MAX” displayed or weekly Maximum UV intensity with a “WEEKLY MAX” displayed. Resetting the UV Statistics Memory In UV Mode, press and hold MEMORY button to reset all UV statistics. Setting Units for UV Dis
Summary of the content on the page No. 8
Troubleshooting Q: “The display shows dashes “---” for UV readings” A: The display will show “- - -” when the wireless connection to remote UV sensor is lost for 30 minutes. Check and/or replace the batteries in UV sensor. Then press and hold DOWN button on the main unit TE923DW or handheld remote control TS607 to enforce a search for the remote signal. If this does not work, check the wireless transmission path from the remote UV sensor to the main unit and change its locations if
Summary of the content on the page No. 9
Accuracy: 1UVI + 10% Transmitting Interval: 300 seconds Power: 2 x UM-3 or AA 1.5V battery Battery life (alkaline): 2 years Weight (without batteries): 2.78oz (79g) Dimensions: 2.58(L) x 4.45(H) x 2.58(D) inches / 65.5(L) x 113(H) x 65.5(D) mm FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, inclu
Summary of the content on the page No. 10
Manufacturer: Hideki Electronics Ltd. Address: Unit 2304-06, 23/F Riley House, 88 Lei Muk Road, Kwai Chung, New Territories, Hong Kong is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. The information above is not to be used as a contact for support or sales. Please call our
