Summary of the content on the page No. 1
SP-11CDS
DIGITAL AUDIO/COMPACT DISC CHANGER
10 DISC AUTO CHANGER
COMPACT DISC AUDIO CHANGER SYSTEM
MODEL SP-11CDS
10-DISC CD CHANGER
INSTALLATION MANUAL
Summary of the content on the page No. 2
PACKING LIST MAIN UNIT Changer SP-11CDS DIGITAL AUDIO/COMPACT DISC CHANGER 10 DISC AUTO CHANGER COMPACT DISC AUDIO CHANGER SYSTEM INSTALLATION PARTS Bracket Stud Bracket 5 Meter Din Cable Hexagonal Bolt (M6 x 15) 1 pc. 4 pcs. 2 pcs 2 pcs Machine Screw Screw Hole Cover Labels Index seal sheet Hexagonal Nut (M4x 10) (M6) 1 pc. 4 pcs. 4 pcs. 1 pc. OTHER ACCESSORIES CD Magazine (P/N SP11M) Installation Manual Owner's Manual 1 pc. 1 pc. 1 pc. 2
Summary of the content on the page No. 3
BEFORE INSTALLING THE UNIT Transport Lock Screws TRANSIT BOLTS (2 RIGHT SIDE, 1 LEFT SIDE) The mechanism in the CD changer is "locked" into place during shipment by the transport screws. Be sure to remove the screws prior to installation. l Caution l After removing the transport lock screws, place a piece of masking tape over each screw hole. The tape will keep out dust , which could cause the unit to malfunction. Installation and Wiring Precautions To prevent a short-circuit
Summary of the content on the page No. 4
INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. CAUTION After setting the built-in anti-vibration springs, place masking tape over the holes. The tape will keep ou
Summary of the content on the page No. 5
PROCEDURE FOR VERTICAL INSTALLATION W/O STUDS Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 4), start with step 2. Attach bracket to each side of the unit, using machine 1 2 Set the 2 anti-vibration springs to position "90". screws with integral flat and lock washers. (M4 x 10). In the vertical position, use holes 2 and 2' as shown at left. NOTE: Use masking tape to cover unused mounting holes on sides of unit. BRACKET (Left Si
Summary of the content on the page No. 6
PROCEDURE FOR 45° ANGLE INSTALLATION W/O STUDS Note If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 4), start with step 2. Set the 2 anti-vibration springs to position "45°". Attach bracket to each side of the unit, using the machine 1 2 screws with flat and lock washers (M4x 10). In the 45 position, use holes 1 and 3' as shown at left. NOTE: Use masking tape to cover unused mounting holes on sides of unit. BRACKET (Left Side) BRAC
Summary of the content on the page No. 7
PROCEDURE FOR CHANGER INSTALLATION USING MOUNTING STUDS Note: Make sure the anti-vibration spring position has been changed and verified for the proper angle mounting (as shown on page 4). 1 Determine mounting location. If unit is to be installed onto mounting studs located under carpet, lift carpet to expose metal chassis and mark position of each stud as shown below in detail A and B. 2 Insert two hexagonal mounting bolts through underside of each bracket (detail A) and mount stud bracket i
Summary of the content on the page No. 8
DIN cable (8-pin) VEHICLE WIRING Mating 8-pin DIN socket on rear of compatible radio chassis (see note 1 below). Car Stereo with CD Changer Controls CD changer NOTE: 1. Check with your Audiovox car audio dealer to be sure your stereo is directly compatible with this CD changer. 2. Wiring instructions for use with FM Modulator/ Commander Systems are included with the CDC-MC1, CDC-MCR2, P-MC3 and P-MCR4 accessories. © 2000 AUDIOVOX CORP., HAUPPAUGE, NY
