Our goal is to provide you with a quick access to the content of the user manual for Haier HR-180T2. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Haier HR-180T2.
If looking through the Haier HR-180T2 user manual directly on this website is not convenient for you, there are two possible solutions:
Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Haier HR-180T2 but the selected pages only. paper.
Below you will find previews of the content of the user manuals presented on the following pages to Haier HR-180T2. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.
The manufacturer keeps on developing various
types of refrigerators, so he has the right to modify
designs, products and technical data without further
FIGURATION OF THE REFRIGERATOR 7 8 6 0 1 5 2 4 3 5 1 4 2 3 1. Low bottle support 2. High bottle support 3. Vegetable box 4. Shelf 5. Drip tray 6. Evaporator 7. Thermostat 8. Light Switch The manufacturer reserves the right to improve the product from time to time without further notice. 1
NOTICE Never store anything dangerous The power supply HR-180T1 127v,60HZ in the appliance, such as HR-180T2 220V, 50/60Hz combustibles, exposives, Single phase. strong acid and alkali. etc. It is not recomended to use any extention cords. Connect the appliance with a properly earthed three-wire plug and socket with a special use. SETTING UP The appliance can be placed with its rear panel directly against the wall. For a good air circulation, the vent grille at the back of the worktop mu
THERMOSTAT The knob graduation 0, 1, 2, 3, 4, 5, 6, 7, does not stand for concrete temperature.The smaller the numbers,the higher the temperature in the compartment and vice versa.Usually,it’s better to put the thermostat in Pos. “1”,Pos. “4”.Pos. “0” shows the power is cut off. STORING FOOD The temperatures in different positions inside the refrigerator are different due to different 1 5 refrigeration distribution.Thus when store food, select proper position to meet your 2 needs. 4 3 The col
NOTES ON STORAGE Where necessary, food should be packed in bags, avoiding giving off strong odours or getting wet or dry. Do not store food too full in the appliance. Allow space among the packages of food for a perfect refrigerating. Hot food or liquid must be allowed to cool to room temperature before placing in it. CLEANING The appliance can only be cleaned at drawn network plug. Clean it with lukewarm water containing a little detergent. In any case do not use hot water,corrosive scouring
DEFROSTING When defrosting, switch off the appliance. Remove food from the ice chamber,it will be defrosted automatically.When 4~6mm defrosting process has been completed, the drip-tray should be depleted. Replace the food and switch on the appliance. NOTES If the appliance The appliance door remains out of should be opened as use for some time, little and briefly pull out the plug as possible to reduce to disconnect the energy consumption appliance from power supply. Clean the interior as descr
In the event of a fault occurring during operation, check first if the fault is due to an operation error. You can repair the following faults yourself. 1. It is not switched on properly, or mains plug properly inserted The appliance does in the socket. not run. 2. The thermostat knob is turned to position “0”. 3. Supply voltage is too low. 1. The appliance is too full of food. 2. The appliance is located too near The temperature inside a source of heat. the appliance is not
LAMP AND LAMP REPLACEMENT Lamp: HR-180T1 127V,15W. HR-180T2 220V, 15W Lamp holder: E14 (lamps exceeding 15W must not be used) When replacing the lamp: * Unplug to disconnect the power and remove the water tray. * Press the positioning pin of the lamp with left hand, and release the shade from the lamp holder by sliding it to the right side. Turn the lamp anti- clockwise for removing. * Replace the water tray. Light Shade ELECTRICAL DIAGRAM Thermostat Overload C Protector Plug Switch S S