Summary of the content on the page No. 1
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
CLASSIFIED PER EN/IEC 60825-1:2007
Complies with FDA performance standards
for laser products except for deviations
pursuant to Laser Notice No. 50, dated
June 24, 2007
User Manual
.
Summary of the content on the page No. 2
TABLE OF CONTENTS 1. BEFORE YOU BEGIN ............................................................................................................................................................................... 3 WHAT IS INCLUDED ................................................................................................................................................................................................. 3 UNPACKING INSTRUCTIONS ..........................................
Summary of the content on the page No. 3
1. BEFORE YOU BEGIN What Is Included 1 x MiN™ Laser FX/RGX/Star 1 x Power Supply 1 x Flexible Tripod 1 x Warranty Card 1 x Adjustable Stand 1 x User Manual 1 x Wireless Remote Unpacking Instructions Immediately upon receipt, carefully unpack this product and check the container to make sure you have received all the parts indicated above in good condition. Claims If the container or the material inside the container (this product and any other accessory i
Summary of the content on the page No. 4
Safety Instructions Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product. Keep this User Manual for future consultation. If you sell this product to another user, be sure that they also receive this document. Always make sure that the voltage of the outlet to which you are connecting this product is within the range stated on the decal or rear panel of the product. Thi
Summary of the content on the page No. 5
Non Interlocked Housing Warning This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation. The laser power levels, accessible if the unit is opened, can cause instant blindness, skin burns, and fires. Laser Safety Notes STOP AND READ ALL THE LASER SAFETY NOTES BELOW Laser Light is different from any other light sources with which you may be familiar. The light from this product
Summary of the content on the page No. 6
Laser Safety Label Reproduction Top Front Rear Bottom MinLaser User Manual 6 August 2011
Summary of the content on the page No. 7
LASER EXPOSURE WARNING Laser light - Avoid direct eye contact! Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard “For Safe Use of Lasers”, available from the Laser Institute of America: www.laserinstitute.org. Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained via the International Laser Display Associ
Summary of the content on the page No. 8
2. INTRODUCTION Product Overview Mode Button LED Indicator Microphone Laser Output Wireless Remote Receiver Green Laser Dimmer Cooling Fan 12 V Power In MinLaser User Manual 8 August 2011
Summary of the content on the page No. 9
3. SETUP AC Power This fixture includes an external power supply which is auto-ranging and runs on 100~240 VAC, 50/60 Hz power. Only use the included power supply! To obtain a replacement power supply, contact Chauvet®. To determine the power requirements for a particular fixture, see the label affixed to the Power Supply back plate of the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its average current draw under normal
Summary of the content on the page No. 10
Adjustable Stand Angle Adjustment Knob A Angle Adjustment Knob B Floor Stand, Flexible Feet (3) MinLaser User Manual 10 August 2011
Summary of the content on the page No. 11
Proper Usage This product is for overhead mounting only. For safety purposes, CHAUVET® recommends mounting your lighting effect products on steady elevated platforms or sturdy overhead supports using suitable hanging clamps. In all cases, you must use safety cables. You can obtain appropriate mounting hardware from your lighting vendor. International laser safety regulations require that laser products must be operated in the fashion illustrated below, with a minimum of 3 meters (
Summary of the content on the page No. 12
4. OPERATING INSTRUCTIONS Manual Mode Access the five different operating modes available in this fixture by using the button on the front panel. Press to cycle through the modes. Please see a description of each mode below. Mode Description 1 Sound-active A 2 Sound-active B 3 Automatic A (constant rotation-slow) Automatic B (stepping rotation-back and 4 forth) 5 Automatic C (constant rotation-fast) The LED indicator on the front of
Summary of the content on the page No. 13
5. APPENDIX General Troubleshooting SYMPTOM POSSIBLE CAUSE(S)POSSIBLE ACTION(S) Check total load placed on the Excessive circuit load electrical circuit. Breaker/Fuse keeps blowing Short circuit along the Check for a short in the electrical power wires wiring (internal and/or external). No power Check for power on Mains. Device does not power up Loose power cord Check power cord Check Control Panel and unit Wrong DMX addressing addressing Damage
Summary of the content on the page No. 14
General Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power.
Summary of the content on the page No. 15
Returns Procedure Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued. Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #). Products returned without the RMA # will be refused. Call CHAUVET® and request an RMA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to pack fixture properly; any shipping damage
Summary of the content on the page No. 16
TECHNICAL SPECIFICATIONS WEIGHT & DIMENSIONS Length ............................................................................................................. 4.3 in (111 mm) Width ................................................................................................................. 3.3 in (85 mm) Height ................................................................................................................ 1.8 in (45 mm) Weight ................................
