Summary of the content on the page No. 1
®
LITTLE WONDER
PARTS LIST, OPERATING AND
ASSEMBLY INSTRUCTIONS FOR
PRO HONDA EDGER, MODEL #6232
®
©2001, LITTLE WONDER , Division Schiller-Pfeiffer, Inc.
Summary of the content on the page No. 2
6. DON’T OVERREACH OR STAND ON IMPORTANT SAFETY INSTRUCTIONS UNSTABLE SUPPORT - Keep good footing and balance at all times. To avoid injury when using WARNING ! ! your Honda Edger, follow 7. NEVER DIRECT DIS- DANGER ! ! basic precautions, including the following: CHARGE OF MATERI- AL TOWARD BYSTANDERS OR ALLOW ANY- 1. READ THESE IMPORTANT SAFETY ONE NEAR THE AREA OF OPERATION. Use INSTRUCTIONS, THE OPERATING INSTRUC- care in directing discharge to avoid glass enclosures, TIONS, ASSEMBLY
Summary of the content on the page No. 3
15. STORE MACHINE INDOORS - When not in 24. STOP THE ENGINE WHEN LEAVING THE use, store indoors in a dry place, locked or otherwise MACHINE UNATTENDED. inaccessible to children. 25. WHEN CLEANING, REPAIRING, OR 16. DO NOT ATTEMPT TO REPAIR MACHINE INSPECTING, make certain the blade and all mov- - Have repairs made by qualified dealer or repairman. ing parts have stopped. Disconnect the spark plug Use only original Little Wonder replacement parts. wire, and keep the wire away from the plug so tha
Summary of the content on the page No. 4
SAFETY DECAL IDENTIFICATION Key #87 P/N 210 Key #84 P/N 4036 Key #85 P/N 211 Key #86 P/N 260 6232 4
Summary of the content on the page No. 5
6 4 0 4 4 - 0 2 1 3 / 4 .10 4 1 6 3 5 7 2 .10 .17 6 1 2 6 6 . 1 0 H a n d l e - S u p p o r t L H 1 .10 .17 .10 .10 8 2 6 7 . 1 0 H a n d l e - S u p p o r t , R H .10 6 4 1 4 1 - 2
Summary of the content on the page No. 6
Summary of the content on the page No. 7
6 1 4 1
Summary of the content on the page No. 8
6. Insert the end of the throttle cable into the hole on THROTTLE INSTALLATION the engine throttle lever. INSTRUCTIONS 7. Place the cable-retaining clamp over the cable, insert the screw and tighten. 1. Remove the air filter cover from the engine. 8. Replace the air filter cover. 2. Use a 10mm socket to loosen the throttle lever pivot nut. 9. The remote throttle lever should move from slow to fast and be approximately centered in its slot. 3. Move the remote throttle lever so that the center of
Summary of the content on the page No. 9
ment, inspection or the like. OPERATING INSTRUCTIONS 4. Operate machine from position where guards block the line of sight to the cutting member. A. BEFORE STARTING E. OPERATING 1. Place Edger on level surface; be sure blade is not obstructed and the area is clear and free of 1. Eye protection must be worn at all times. Use bystanders. Your Edger is equipped with a Honda common sense and exercise caution at all times when 4-cycle engine. operating your Edger. 2. Check oil level, and be sure cr
Summary of the content on the page No. 10
vered "wheelbarrow fashion." WARNING: The engine on your Pro Honda Edger is not equipped with a spark arrester and USER MAINTENANCE if machine is to be used on any forest-covered, brush-covered, or grass-covered unimproved INSTRUCTIONS land, before using on such land a spark arrester must be added to the muffler. The arrester must 1. Keep all nuts, bolts and screws tight. be maintained in effective working order by the operator. In the State of California, the above is 2. Never store the machine
Summary of the content on the page No. 11
TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A. Engine will not start 1. Out of gasoline. 1. Fill gasoline tank. 2. Spark plug lead wire loose 2. Reconnect spark plug lead wire. or disconnected. 3. Defective spark plug. 3. Replace spark plug. 4. Throttle control lever not 4. Move throttle control lever to start position. in proper position. 5. Engine flooded or flooding. 5. Start engine with choke fully open. 6. Stale or contaminated 6 Drain, clean tank and system and refill wi
Summary of the content on the page No. 12
7 0 1 2 / 4 1 6 3 2 4 0 s i .
