Summary of the content on the page No. 1
0102 095 50023
CLASS 2 – FLAME SYSTEM 3
USERS (Pages 2-3)/ INSTALLATION (Pages 4-9)
AND SERVICING INSTRUCTIONS
THIS CAT I2H APPLIANCE IS FOR USE
ON NATURAL GAS G20 AT A SUPPLY
PRESSURE OF 20 mbar IN GB and IE
HAND THESE INSTRUCTIONS TO THE USER
Summary of the content on the page No. 2
USERS INSTRUCTIONS Description This Royal Cozy Fires Decorative Fuel Effect gas fire has been developed to give a realistic coal burning appearance with the instant control and convenience of gas. The fire has been constructed to enable it to be installed into most applications (using the optional spacer frame) where the warmth and comfort of an open fire with high radiant heat is required. This appliance is intended for decorative purposes and the coal bed uses ceramic simulated (coals) to give
Summary of the content on the page No. 3
3. 0nce a pilot-flame has been established; keep the control depressed for a further 20 seconds. Release the gas control and check that the pilot remains lit. 4. Depress the gas control slightly and turn anti-clockwise until the indicator mark is aligned with the letters HIGH. The burner will cross light from the pilot. 5. Depress the gas control slightly and turn anti-clockwise until the indictor mark is aligned with the letters LOW. The burner will now be at minimum rate. 6. To turn ‘off ‘ the
Summary of the content on the page No. 4
INSTALLATION INSTRUCTIONS THE FOLLOWING SECTION LISTS THE INSTALLATION REQUIREMENTS AND REGULATIONS A competent person in accordance with the current Gas Safety (Installation and Use) Regulations or the rules in force and in accordance with the manufacturer’s instructions must install the appliance; failure to do so could lead to prosecution. The following are the relevant Codes of Practice and British Standards. The Building Regulations issued by the Department of the Environment. The Building
Summary of the content on the page No. 5
Installing the Appliance Check that the chimney and flue structure are sound and conform to the following flue requirements. a) A conventional brick or stone chimney with a minimum effective cross sectional dimension of 225 x 225mm. A lined flue with a minimum diameter of 175mm having a chairbrick and throat forming lintel conforming to BS 1251 or a builders opening (constructed of non-combustible material) measuring 540mm high x 400mm wide with a sufficient depth for debris collection. If a cha
Summary of the content on the page No. 6
Installation using a 5” Diameter Metal Flue Box Important: The spigot restrictor marked ’B’ must be fitted. See page 7. When the metal flue box is to be built-in as a false chimneybreast using the timber studwork with plasterboard facing, the metal flue box should be enveloped with insulation material such as Rockwool or similar to prevent a build-up of heat within the structure. Either an air gap of 75mm should be maintained between any combustible materials and any part of the metal flue box o
Summary of the content on the page No. 7
The two slots in the rear of the base of the firebox may be used to secure the appliance in position. Where no spacer is used the unit will require securing at the top using the two holes in the top corner plate and the No 10 c/sk screws provided. This is needed to effect a seal with the flue. Vent Box Installed with Spacer frame a. 6 holes are provided in the rear of the spacer frame with access through the front of the frame. Only 4 fixing positions are required, 1 at the bottom of each leg an
Summary of the content on the page No. 8
Checking Operation of Fire Turn on the gas supply at the meter and to the appliance at the isolating cock. Purge the air from the appliance. Press and turn the gas control anti-clockwise, keep the control fully depressed. The igniter will operate and the pilot will light, check that the electrode is sparking to the head of the pilot burner, continue until a pilot ignition is established. 0nce a pilot- flame has been established; keep the control depressed for a further 20 seconds. Release the ga
Summary of the content on the page No. 9
Removal of Debris or Soot Deposits Debris from any source or any soot formed shall require removal. Allow the appliance to cool sufficiently before removing all of the coals and firebed components for cleaning purposes. Once all the ceramics are removed from the firebed check that no debris is located in the burner slots. If any debris is present it may easily be removed by using a small piece of thin cardboard to ease out any foreign matter. Be sure to remove the cardboard after use. To ensure
Summary of the content on the page No. 10
Page 10
Summary of the content on the page No. 11
Depth A is to be a minimum of 150mm from the knee to the front face of the surround with the sapcer fitted to satisfy the debris collection requirement Depth B is Nominally 70mm. If no chairbrick is fitted, the minimum distance required between the rear of the opening and the front face of the surround is 210mm without spacer frame fitted. Page 11
Summary of the content on the page No. 12
Page 12
Summary of the content on the page No. 13
Page 13
Summary of the content on the page No. 14
Page 14
Summary of the content on the page No. 15
Page 15
Summary of the content on the page No. 16
Page 16
Summary of the content on the page No. 17
Page 17
