Universal SPC-150T user manual

Summary of the content on the page No. 1

OPERATING INSTRUCTIONS
National-Riverside SPC
PROPANE
Universal ALL-PRO
HEATERMODEL 80-FAP
CONSTRUCTION
HEATER
MODELS 150-FAST MODEL SPC-150T
FORCED AIR
150,000 BTU/HR
HEATER SPECIFICATIONS - 150
Type of Gas For Use with Propane Gas Only
Input Rating 150,000 BTU/hr
Fuel Consumption 7 Lbs/hr
Gas Supply Pressure
to Regulator Max: Bottle Pressure
Min: 5 psig
Regulator Out 11" W.C.
Fuel Orifice Size 1.00 mm Drill - 18 Holes
Electrical Input 115V, 60Hz 10, 4a
Minimum Operating Voltage 100

Summary of the content on the page No. 2

OPERATING PRECAUTIONS SAFETY PRECAUTIONS This is a propane, direct-fired, forced air heater. It's intended 1. Check the heater thoroughly for damage. DO NOT use is primarily temporary heating of buildings under construc- operate a damaged heater. tion, alteration or repair. 2. DO NOT modify the heater or operate a heater which has been modified from its original condition. ! WARNING 3. Use only propane gas. NOT FOR HOME OR RECREATIONAL VEHICLE USE 4. Use only VAPOR WITHDRAWAL propane supply.

Summary of the content on the page No. 3

OPERATING INSTRUCTIONS PROPANE FUEL PRECAUTIONS WARNING: PREPARING FOR OPERATION Local codes for installation of propane systems may vary 1. Check the heater for possible shipping damage. If considerably. Therefore, ask your local propane supplier for any is found, immediately notify your dealer. advice on propane system installation in your particular area. 2. Follow all of the "Precautions" on pages 2 & 3. In the absence of local codes, install in accordance with 3. Connect the POL fitting o

Summary of the content on the page No. 4

150-FAST/SPC-150FAST Item Part No. Description Qty Item Part No. Description Qty. 150-FAST SPC-150FAST 150-FAST SPC-150FAST 1 1700 1712 Burner Shell Assembly 1 28 3441 3441 Thermostat Mounting Bracket 1 2 1672 1672 Middle Cylinder Assembly 1 29 6070 6070 Clamp Loop, 5/16 1 3 1168 1168 Orifice Assembly 1 30 1734 1734 Thermostat Assembly 1 4 1146 1146 Flame Holder Assembly 1 31 10739 10739 Flame Control 1 5 1550 1550 High Limit Control

Summary of the content on the page No. 5

WIRING DIAGRAM WIRING CHART PART NO. COLOR LENGTH FROM TO 1041 White 4 1/2" Terminal Block Valve 1041 White 4 1/2" Flame Control Valve Valve 1226 Red (Hi-Temp) 16 1/2" High Limit Switch Valve 1226 Red (Hi-Temp) 16 1/2" Terminal Block High Limit Switch 1226 Red (Hi-Temp) 16 1/2" Flame Control Valve High Limit Switch 1188 Green 6" Flame Control (Ground) Ground 1111 Orange 8" Flame Control (Ignition) Spark Plug 1959 Green 7" Flame Control (Harness) Ground 1959 Red 7" Flame Control (Harness) Termin

Summary of the content on the page No. 6

150-FAST/SPC-150T SERVICING TECHNICAL INFORMATION A hazardous condition may result if a heater is used that has been modified or is not functioning properly. When the HOW MUCH HEAT DO I REQUIRE? heater is working properly: * The flame is contained within the heater. For economy, it is important to match input to that * The flame is essentially blue with perhaps required. But heat requirements often vary. For ex- some yellow tipping. ample, it usually takes a lot more heat to get things warm