Summary of the content on the page No. 1
Copywriter
Flash Duplicator
Series
User’s Manual
www.microboards.com Version 1.1
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
Table of Contents Introduction......................................................................................................................... 5 What’s Included.............................................................................................................. 5 Installation........................................................................................................................... 5 Loading and Unloading Flash Cards.......................................
Summary of the content on the page No. 4
4
Summary of the content on the page No. 5
Introduction The Copywriter Flash Duplicator allows you to make fast copies of USB flash cards. This series is available in 3, 7, or 11 copy configuration. What’s Included When unpacking your Copywriter Flash Duplicator system, the following items should be included: • Copywriter Flash Duplicator • Users Manual (this document) and Starter Kit • Power Cord If any of these items are missing, please contact your distributor or Microboards Technology Technical Support: United Stat
Summary of the content on the page No. 6
Hardware Description Controller Interface and Display Recorder Ports (all ports below the first row are also recorder Reader ports) Port Copywriter USB Power Switch 11 Flash Duplicator The Copywriter Flash Duplicator consists of a reader port, 3, 7, or 11 flash drive ports and Controller module. The master card will always be inserted into the TOP LEFT port, which is outlined. The blank cards will always be inserted into the remai
Summary of the content on the page No. 7
Main Menu Flowchart SYNCHRONOUS: OK Copy 3669M TOTAL: 11/0 Load Next Blank Cards, 1. Copy 10% 0:53 367M Pass: 11 Fail: 0 Press OK ESC ▼ SYNCHRONOUS: OK Compare 3669M TOTAL: 11/0 Load Next Blank Cards, 2. Compare 10% 0:53 367M Pass: 11 Fail: 0 Press OK ESC ▼ SYNCHRONOUS: OK Copy 3669M Copy 3669M TOTAL: 11/0 Load Next Blank Cards, 3. Copy & Compare 10% 0:53 367M 10% 0:53 367M Pas
Summary of the content on the page No. 8
Main Menu There are 6 different Main Menu items for the Copywriter Flash Duplicator: Copy, Compare, Copy & Compare, Information, Utility, and Setup. For the Setup options, please refer to page 9. These instructions refer to using 11 USB recorder ports (available only in the USB 11 Flash Duplicator), but the instructions will not differ when using any of the Copywriter Flash Duplicators. Any Copywriter Flash Duplicator model will operate using any number of the available recorder ports.
Summary of the content on the page No. 9
Synchronous Duplication If the entire source content cannot be stored in the memory buffer, Synchronous duplication will be required. Copy 3669M Place your master card into the reader port and your blank cards into the recorder ports. 10% 0:53 367M Press the OK button on the controller interface. If all recorder ports are filled, duplication will begin. If not, the display will show how many target cards are in place; press OK again to begin duplicatio
Summary of the content on the page No. 10
Utility The Utility function is available for erasing inserted cards and updating the Duplicator firmware. Measure Speed The Measure Speed function can be turned on to measure the exact speed of the flash read and write. Media Check This function checks the media quality, and can be set to 3 different levels: Normal 100%, Strict 100%, and Setup Range. Regardless of the setting, if the check detects a read or write error, the LED for that flash card will show red. Normal 100% will use b
Summary of the content on the page No. 11
Setup Menu The Setup function gives you access to some of the default settings used by the Copywriter Flash Duplicator. Startup Menu The Startup Menu selection allows you to select the main menu item that appears when the Copywriter Flash Duplicator starts up. The default setting is 1. Copy. Main Menu items 1 through 6 can be selected. Copy Area Only Data Area With the Copy Area setting selected as Only Data Area, the system will automatically analyze the source flash card’s file for
Summary of the content on the page No. 12
Troubleshooting and Frequently Asked Questions Is there any limitation for copy file format? You can use "Only Data Area" to copy FAT16/32, NTFS, Linux (ext3) format, it will only copy the data, and therefore the copy speed will be quicker. If you want to copy other formats, it can use "Whole Area" to copy whole Flash; the format of the flash will not be a considered. How do I know the data is a true copy of the master? The duplicator has CRC check capability and the ability to compa
Summary of the content on the page No. 13
Specifications Recorder Card Dimensions, inches Model Weight Ports Format (H x W x D) CFD-USB-03 3 USB 7 x 7.5 x 11 10 lbs CFD-USB-07 7 USB 7 x 7.5 x 11 11 lbs CFD-USB-11 11 USB 11 x 7.5 x 17 17 lbs Contact Information For technical questions or support issues, please contact Microboards Technology technical support at: United States Europe Japan PH: 952-556-1639 PH: +44 (0) 845 230 7800 PH: 03-3561-2266 FAX: 952-556-1628 www.microboards.co.uk www.microboards.co.jp support@mi
