Garland GMIU3.5 user manual

Summary of the content on the page No. 1

N
O
L
I
I
T
S
A
INSTALLATION AND
OPERATION MANUAL
GARLAND INDUCTION
SINGLE, MULTI-FUNCTIONAL
TABLE TOP UNITS,
MODELS: GMIU3.5 &
GMIU5.5
C CM
86037
CONFORMS TO UL-197 & NSF-4 CERTIFIED TO
FOR YOUR SAFETY: CAN/CSA C22.2NO. 109 VDE EN60335-2-38.
DO NOT STORE OR USE GASOLINE
PLEASE READ ALL SECTIONS OF THIS MANUAL
OR OTHER FLAMMABLE VAPORS OR
AND RETAIN FOR FUTURE REFERENCE.
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
THIS PRODUCT HAS BEEN CERTIFIED AS
APPLIANCE
COMMERCIAL COOKING

Summary of the content on the page No. 2

Page 2 Part # 4520897 (01/31/08)

Summary of the content on the page No. 3

TABLE OF CONTENTS DIMENSIONS AND SPECIFICATIONS, . . . . . . . . . . . . . . . . . . . . . . . .4 . . . . . . . . . Operation And Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Operation Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . .

Summary of the content on the page No. 4

DIMENSIONS AND SPECIFICATIONS, 5-3/8" 3-7/8" (138mm) (97mm) removable washable 7-7/8"(198mm) airlter fresh air 2-5/8"(65mm) 6'cord and plug (208/240 volt, 60 cycle units only) 2-3/4"(70mm) 8-3/8"(210mm) view A: exhaust 12-5/8"(320mm) 5-7/8" (144mm) exhaust 15"(380mm) Plug Configurations : Electrical Model Plug Characteristics 208V/60Hz/1Ø GMUI-3.5 240V/60Hz/1Ø GMUI-5.5 208V/60Hz/3Ø Electrical Loading: Model Watts 208/60/1 208/60/3 240/60/1 230/50/1 400/50/3 440/60/3 GMIU-3.5 3500 16 amp N/A 14

Summary of the content on the page No. 5

DIMENSIONS AND SPECIFICATIONS, Continued Operation And Control Operation Conditions Lamp operation 24V DC/max. 40mA (red) Max. Tolerance Of The Nominal +6/-10% Supply Voltage Key pad and LED display Supply Frequency 50/60 Hz Protection Class 1P 43 Minimal Diameter Of The Pan 5” (127mm) INTRODUCTION Description of products Application We manufacture several basic types of induction cookers The following instructions contain information, which with various performances and measurements. All are

Summary of the content on the page No. 6

INSTALLATION Induction Unit Location Side View The cooker has to be set up on a stable place like a table. It requires an area of at least 400 x 480 mm (15.7” x 18.9”). d: minimum distance to the wall = 40 mm The air inlet and air outlet must not be obstructed, the table d must be able to withstand a loading of 40 kg (88 lbs). The cooker doesn’t have to be fixed on the table. The key pad to operate the cooker must be easily accessible. It must be set up in such a way that it cannot fall d

Summary of the content on the page No. 7

OPERATION Your cooker must be positioned in a suitable place and Display connected to a voltage supply. Make sure the cooker is well positioned and free from exposure to vibration. Make sure the unit is in the “OFF” position. Remove all objects from the glass ceramic cooking zone, verify if this area is neither cracked not broken. Don’t continue with use when the glass ceramic cooking zone is cracked or broken, immediately switch off and disconnect the cooker from the outlet. CAUTION The g

Summary of the content on the page No. 8

OPERATION Continued The pan should always remain in the center of the heating Heating area, otherwise the bottom of the pan is heated unequally The induction cooker is immediately ready for operation by and the food inside the pan may burn. When heating oil or pushing the “ON/OFF” key. The shining indicator operation grease, constantly check the pan to prevent oil and grease lights shows that energy is transferred to the pan. The power from overheating and burning. ratings “low, mid and h

Summary of the content on the page No. 9

OPERATION Continued Pan Detection Out Of Operation During pan detection, the indicator operation flashes. No If the cooker is out of operation make sure that the control power is transferred and the indicator lamp flashes if no pan knob is in the “OFF” position. If you don’t use the cooker for or an unsuitable pan is detected. Pans having a diameter a longer period (several days) unplug the unit. Make sure smaller than 127 mm (5”) are not detected. that no liquid can enter into the cooker and

Summary of the content on the page No. 10

SAFETY CONCERNS Continued 2. Switch the control knob off it you take the pan away for a 7. This induction unit is equipped with a grease filter, placed while. This will avoid having the heating process continue at the bottom of the case. The grease filter is fixed on a automatically when a pan is placed back on the heating mounting with support angles and can be pulled out area. So, if any person starts to use the cooker, he/she will from the operator’s side. have to start the heating process

Summary of the content on the page No. 11

TROUBLE SHOOTING CAUTION Do not open the cooker, dangerous electric Error Messages voltage inside Order of error message: The indicator lamp “ON” flashes for The cookers may only be opened by authorized service an interval of 0.6 sec. The number of the following short personnel. flashes has to be counted and indicating the kind of error corresponding to the following mentioned code system. Stop any actions if the heating area (Ceran plate) is cracked or broken, the induction cooker must be

Summary of the content on the page No. 12

TROUBLE SHOOTING Continued Troubling Shooting Guide Action to take through operator or Fault Possible Cause operating personnel No heating indicator operation is OFF No electrical supply Check if the electrical supply (cable (dark) plugged in the wall socket), check preliminary fuses Control in off-position Push control on Pan too small (bottom diameter less Use a suitable pan than 5” (127 mm ) Pan is not placed in the center of the Move the pan to the center of the heating area (the cooker

Summary of the content on the page No. 13

TROUBLE SHOOTING Continued Action to take through operator or Fault Possible Cause operating personnel After a longer permanent operating Coil overheated, cooking area too hot Switch cooker off, remove pan and wait time, the heating switches off and on until the cooking area has cooled off Empty pan within minutes Pan with overheated oil Small metallic objects (e.g. Spoon) are Pan detection tuned incorrectly Control logic board heated up within the cooking area * To verify if the pan is suit

Summary of the content on the page No. 14

Page 14 Part # 4520897 (01/31/08)

Summary of the content on the page No. 15

Part # 4020897 (01/31/08) Page 15

Summary of the content on the page No. 16