Streszczenie treści zawartej na stronie nr. 1
XR10/XR20 Command Processor Panels
Installation Guide
10/26 Zone Burglary/Fire/Access Control Panels with Built-in Communicator
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
LT-0229 (5/97)
Downloaded from: http://www.guardianalarms.net
Streszczenie treści zawartej na stronie nr. 2
MODEL XR10/XR20 COMMAND PROCESSOR INSTALLATION GUIDE FCC NOTICE This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance with the manufacturer's instructions, may cause interference with radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specification in Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection ag
Streszczenie treści zawartej na stronie nr. 3
TABLE OF CONTENTS Section Panel Specifications Power supply........................................................................................ 1.1 Communication .................................................................................... 1.2 Panel zones ......................................................................................... 1.3 Keypads ............................................................................................... 1.4 Outputs .......................
Streszczenie treści zawartej na stronie nr. 4
TABLE OF CONTENTS Section Reset Jumpers J16 Description ......................................................................................... 14.1 Universal UL Burglary Specifications Introduction ........................................................................................ 15.1 Wiring ................................................................................................. 15.2 Police station phone numbers ............................................................ 15.3
Streszczenie treści zawartej na stronie nr. 5
Introduction Panel Specifications 1.1 Power supply Transformer Input: 16.5 VAC 40VA (Models 320 wire-in or 321 plug-in) Standby Battery: 12 VDC 6.5Ah (40VA transformer charges up to 2 batteries) Auxiliary Output: 12 VDC at 500mA Bell Output: 12 VDC at 1.5 Amps Smoke Detector Output: 12 VDC at 100mA All circuits inherent power limited 1.2 Communication Built-in SDLC Digital Dialer communication to DMP Model SCS-1 Receivers Built-in 4-2 communication to non-DMP receivers. Built-in M2E (Radionics
Streszczenie treści zawartej na stronie nr. 6
Introduction 2.3 Before you begin Before installing the XR10/XR20, we recommend you read through the entire contents of this guide. Familiarize yourself with the features of the panel and the key points to remember during the installation. Be sure to read and understand all of the caution statements printed in bold italics. In addition to this installation guide, you should also read through and familiarize yourself with these other product documents: • XR10 Programming Guide (LT-0230) • XR20 P
Streszczenie treści zawartej na stronie nr. 7
Introduction System Components 3.1 Description The DMP XR10/XR20 system is made up of an alarm panel with built in communicator, an enclosure, a 16.5 VAC transformer, and a 12 VDC 6.5 Ah battery. You can add up to four Security Command keypads to the system and can also connect auxiliary devices to the panel's open collector outputs to expand the basic system. Combined current requirements of additional modules may require an auxiliary power supply. Refer to section 6.6 in this guide when calcul
Streszczenie treści zawartej na stronie nr. 8
Installation Installation 4.1 Mounting the enclosure The metal enclosure for the XR10/XR20 must be mounted in a secure, dry place to protect the panel from damage due to tampering or the elements. It is not necessary to remove the XR10/XR20 PC board when installing the enclosure. Dual 1/2" and 3/4" Conduit Knockouts J16 J11 1 Reset Jumper 2 3 4 J4 Phone Jack Connector U11 1 23 4 56 78 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 AC AC +B -B BELL GND RED YEL GRN BLK SMK Z1 GND Z2 Z3 GND Z
Streszczenie treści zawartej na stronie nr. 9
Installation 4.2 Mounting keypads Security Command keypads have removable covers that allow you to easily mount the base with keypad circuit board to a wall or other flat surface using the screw holes provided on each corner. Before mounting the base, connect the keypad wire harness leads to the 4-wire keypad data bus cable from the panel. Next, attach the keypad wire harness connector to the pin connector on the keypad circuit board, mount the base, and install the keypad cover making sure all
Streszczenie treści zawartej na stronie nr. 10
Installation 6.4 Discharge/recharge The XR10/XR20 battery charging circuit float charges at 13.9 VDC at a maximum current of 1.2 Amps using a 40VA transformer. The total current available is reduced by the combined auxiliary current draw from terminals 7, 11, and 25. The various battery voltage levels are listed below: Battery Trouble: Below 11.9 VDC Battery Restored: Above 12.6 VDC 6.5 Battery supervision The XR10/XR20 tests the battery once every hour when AC power is present. The test lasts f
Streszczenie treści zawartej na stronie nr. 11
Installation Bell Output 7.1 Terminals 5 and 6 Nominal 12 VDC is supplied by terminal 5 on the panel to power alarm bells or horns. The output is rated for a maximum output of 1.5 Amps. This output can be steady or pulsed depending upon the Bell Action specified in Output Options. Terminal 6 is the ground reference for the bell circuit. Keypad Data Bus 8.1 Description Terminals 7, 8, 9, and 10 of the XR10/XR20 panel are designated as the keypad data bus. In addition to keypads, the XR20 allows t
Streszczenie treści zawartej na stronie nr. 12
Installation 10.2 Operational parameters Each burglary protection zone detects three conditions: open, normal, and short. The parameters for each are listed below: Condition Resistance on zone Voltage on right terminal Open over 1300 ohms over 2.0 VDC Normal 600 to 1300 ohms 1.2 to 2.0 VDC Short under 600 ohms under 1.2 VDC 1K 1K 1K NORMALLY CLOSED CONTACTS NORMALLY OPEN CONTACTS COMBINATION: NORMALLY OPEN AND NORMALLY CLOSED CONTACTS Figure 3: Protection zone contact wiring 10.3 Zon
Streszczenie treści zawartej na stronie nr. 13
Installation Annunciator Outputs 12.1 Description The four annunciator outputs can be programmed to indicate the activity of the panel's zones or conditions occurring on the system. Annunciator outputs do not provide a voltage but instead switch to ground voltage from another source. The outputs can respond to any of the conditions listed below: 1) Activation by zone condition: Steady, Pulse, Momentary, or Follower 2) Manually from the Security Command keypad 3) Communication failure 4) Arme
Streszczenie treści zawartej na stronie nr. 14
Installation 13.4 Ground start To configure the XR10/XR20 for ground start operation, you must install the appropriate ground start module and program one of the panel's available annunciator outputs for Ground Start operation. Refer to the XR10/XR20 Programming Guide for complete programming information. Reset Jumpers J16 14.1 Description There are two reset jumpers located at the top right of the panel's circuit board labeled RESET. Momentarily shorting these jumpers allows you to reset the mi
Streszczenie treści zawartej na stronie nr. 15
Installation UNIVERSAL UL BURGLARY SPECIFICATIONS 15.1 Introduction The programming and installation specifications contained in this section must be completed when installing the XR10/XR20 panel in accordance with any of the UL burglary standards. Additional specifications may be required by a particular standard. 15.2 Wiring All wiring must be in accordance with NEC, ANSI/NFPA 70, UL 681, and UL 611 for all burglary installations. 15.3 Police station phone numbers The digital dialer telephon
Streszczenie treści zawartej na stronie nr. 16
Installation UL 1610 and 1076 SPECIFICATIONS Central-Station and Proprietary Burglar-Alarm Units 17.1 Opening/Closing reports The Opening/Closing Reports option must be programmed as YES. See section 5.2 of the XR10 Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305). 17.2 Automatic bell test This option must be programmed as YES. See section 7.3 of the XR10 Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305). 17.3 Proprietary dialer The Model XR10/XR20 provides Grade
Streszczenie treści zawartej na stronie nr. 17
Installation 19.6 Mercantile Safe and Vault When the DMP Model 349A housing is used, the XR10/XR20 provides operation as a mercantile safe and vault alarm. Bell Supervision and wiring must be in accordance with UL 681. If the Model XR10/XR20 is mounted outside the safe or vault, tamper protection and the Sentrol Model 5402 or Potter EVD listed vibration detectors should be used. The XR10/XR20 does not provide operation as a Bank Safe and vault alarm. 19.7 Line security for Police Connect Basic l
Streszczenie treści zawartej na stronie nr. 18
Troubleshooting CALIFORNIA STATE FIRE MARSHAL SPECIFICATIONS 22.1 Bell output definition The bell output of the Model XR10/XR20 must be programmed to operate steady on burglary alarms and pulsed on fire alarms. See sections 7.4A and 7.4B of the XR10 Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305). Troubleshooting Section 23.1 Description This section of the XR10/XR20 Installation Guide provides troubleshooting information for use when installing or servicing an XR10/XR20 system
