Instrukcja obsługi Harbor Freight Tools 92622

Streszczenie treści zawartej na stronie nr. 1

1” DRIVE INDUSTRIAL 1” DRIVE INDUSTRIAL 1” DRIVE INDUSTRIAL
1” DRIVE INDUSTRIAL 1” DRIVE INDUSTRIAL
IMP IMPACT WRENCH ACT WRENCH
IMP IMP IMPACT WRENCH ACT WRENCH ACT WRENCH
92622
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2004 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express writt

Streszczenie treści zawartej na stronie nr. 2

Specifications Item Description Torque 1,400 FT./LBS. Working Pressure 100 PSI, and 115 PSI (maximum) Air Inlet ½ inch – 14 NPT with screen Drive One inch, Inline air impact Regulator on Unit 3 torque settings: 1, 2, & 3; Left and Right direction Overall Dimensions 22-3/4 (L) x 7-3/4 (W) x 7-1/4 (H) with side handle Weight 31.7 LBS. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts lis

Streszczenie treści zawartej na stronie nr. 3

8. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorize

Streszczenie treści zawartej na stronie nr. 4

Impact Wrench Safety Precautions 1. Disconnect air before servicing. Do not attempt to change sockets, disassemble, or service tool with air hose attached. 2. Use only specified operating air pressure. Never operate tool above the specified operating air pressure range. 3. Do not use combustible gases. Do not use combustible gases as a power source, or use tool in areas where combustible gases are stored. 4. Avoid possible kickback injury. Hold the tool with both hands during operation so th

Streszczenie treści zawartej na stronie nr. 5

Assembly The Air Hammer comes completely assembled, except for the air inlet fitting and handle. Note: Use pipe thread seal or Teflon tape on all threaded connections. Caution: The compressor must be off and all the air bled out before making any con- nections. Mount Handle 1. Using Cap Screws (50), and the supplied Allen Wrench, mount the D-type Handle (49) to the Hammer Case (43). 2. Securely tighten all Cap Screws. Air Connection 1. Attach the Air Hose Fitting (56) into the Air Inlet (10) fit

Streszczenie treści zawartej na stronie nr. 6

Operation WARNING: Only use one inch sockets with the torque capability of at least 1400 FT./ LBS.. Otherwise, the socket could fly off the Anvil or break apart, causing injury. 1. Put on the impact safety glasses and ear plugs. 2. Select the desired one inch socket and verify it fits properly on the nut or bolt being secured or removed. Then, secure the socket on the Anvil (41) of the Impact Wrench. 3. Hand screw on the nut or bolt as far as possible. 4. Turn the air compressor on and set the

Streszczenie treści zawartej na stronie nr. 7

Maintenance 1. After each use, wipe the Impact Wrench with a clean cloth to remove any dirt and grease buildup. 2. To maintain tool life, always lubricate the air line by adding a few drops of pneumatic tool oil to the air line (or Air Inlet) before each use. Or, install the automatic oiler-filter system as illustrated on page 5. 3. Before each use, drain water out of the air compressor tank and condensation from the air lines. Refer to the Air Compressor Operation Manual. 4. Store the Impact Wr

Streszczenie treści zawartej na stronie nr. 8

Assembly Drawing PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU- TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS