Streszczenie treści zawartej na stronie nr. 1
1
9
8
7
#
0
PQRS
6
5
4
3
2
TUV WXYZ
OPER
TONE
DEF
ABC
MNO
JKL
GHI
MEMORY PROGRAM FLASH REDIAL
USER’S MANUAL
Part 2
Design Line Telephone 145
Please also read
Part 1 — Important
Product Information
AT&T and the globe symbol are registered trademarks of AT&T Corp.
licensed to Advanced American Telephones.
© 2000 Advanced American Telephones. All rights reserved.
Printed in China. 850003054 Issue 1AT&T 6/00
RINGER OFF LO HI TONE PULSE
Streszczenie treści zawartej na stronie nr. 2
1 9 8 7 # 0 PQRS 6 5 4 3 2 TUV WXYZ OPER TONE DEF ABC MNO JKL GHI MEMORY PROGRAM FLASH REDIAL INSTALLATION Programs a number in memory Accesses custom calling services Accesses numbers Redials stored in memory last call made Receiver Volume (on left side of base) Handset Dial Mode switch Ringer Volume Temporary Tone Dial Mode This telephone has a selectable push-button dial and will work with either tone or rotary telephone service. It can be set to work directly with long-distance or certain ot
Streszczenie treści zawartej na stronie nr. 3
INSTALLATION TABLE/DESK INSTALLATION This telephone includes a 7-foot line cord with a modular plug on each end. You’ll use this cord to connect the telephone to a modular jack. 1. Connect line cord to telephone Plug the long line cord into the jack on the underside of the telephone base. Then feed the line cord through the channel provided so the telephone sits flat on your table or desk during use. 2. Set Dial Mode switch This product comes set in the TONE mode. Make sure you choose the corre
Streszczenie treści zawartej na stronie nr. 4
INSTALLATION WALL INSTALLATION 1. Reverse the handset tab. When mounting the telephone on a wall, you must reverse the handset tab. This tab holds the handset when you hang up. Hold down the switchhook, and slide the tab up and out of its slot (Figure 1). Turn the tab so that the end with the “hook” is up (Figure 2). Then insert the tab back into its slot (Figure 3). Figure 1 Figure 2 Figure 3 2. Fill in directory card The enclosed directory card has an adhesive backing which lets you place it i
Streszczenie treści zawartej na stronie nr. 5
INSTALLATION 5. Set the Dial Mode switch This product comes set in the TONE mode. Make sure you choose the correct dialing method (TONE/PULSE); touch tone dialing will not work if you have dial pulse service. 6. Connect handset to telephone base Connect one end of the coiled handset cord to the base. Plug the other end into the handset. Then hang up the phone. 7. Check for dial tone Lift the handset and listen for a dial tone. If you can’t hear a dial tone, refer to “In Case of Difficulty” and
Streszczenie treści zawartej na stronie nr. 6
OPERATION Redial The telephone always stores in memory the last number dialed. To dial the same number again, lift the handset, and press REDIAL . The redial memory can accept numbers up to 32 digits long. The number will remain in memory until you change it by dialing another telephone number. For privacy, you can erase the redial memory. Lift the handset, then press any digit (1-9). Flash FLASH Press instead of pressing the switchhook to activate customer calling services such as call waiting
Streszczenie treści zawartej na stronie nr. 7
MEMORY Memory Features Numbers will remain stored in memory unless you erase or change them by entering other numbers. Capacity: This telephone can store up to nine different phone numbers, each up to 18 digits long. Speed Dialing: Nine telephone numbers can be stored in standard speed-dialing locations. You can dial any of these numbers by pressing two buttons. NOTE: Numbers programmed into a memory location might not be retained if the telephone has been unplugged from the line jack for a half
Streszczenie treści zawartej na stronie nr. 8
IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. No Dial Tone + Make sure all plugs are connected properly. Inspect the line cord connections at the modular jack and at the telephone. Also inspect the coiled handset cord connections at both ends. + Unplug the telephone and connect it to another modular jack. If it still does not work, try another telephone; if neither telephone works, the problem is not in this telephone. The trouble may be caused
