Manual do usuário Chief Manufacturing LCD Swivel Stand MSS6000

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS
LCD Swivel Stand
MSS6000

Resumo do conteúdo contido na página número 2

MSS6000 Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and Milestone AV Technologies, Inc., and its affiliated corporations follow all instructions can result in serious personal injury, and subsidiaries (collectively, "Milestone"), intend to make this damage to equipment, or voiding of factory warranty! It is the manual accurate and complete. However, Milestone makes no installer’s responsibility to make sure all components are claim that the information

Resumo do conteúdo contido na página número 3

Installation Instructions MSS6000 LEGEND Pencil Mark Tighten Fastener Apretar elemento de fijación Marcar con lápiz Stiftmarkierung Befestigungsteil festziehen Apertar fixador Marcar com lápis Segno a matita Serrare il fissaggio Bevestiging vastdraaien Potloodmerkteken Marquage au crayon Serrez les fixations Drill Hole Loosen Fastener Aflojar elemento de fijación Perforar Bohrloch Befestigungsteil lösen Desapertar fixador Fazer furo Praticare un foro Allentare il fissaggio Bevestiging losdraaien

Resumo do conteúdo contido na página número 4

MSS6000 Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 3/16" 5/32" 3/8" (Provided) (Provided) PARTS A (1) B (5) D (1) C (1) .5x.5x.203 3/16" 5/32" 4

Resumo do conteúdo contido na página número 5

Installation Instructions MSS6000 To install a display with a height greater than 24": INSTALLATION 1. Remove slide plate assembly from the base by Mount Installation removing four 5/16-18 x 3/4" button head cap screws, and Free Standing (not anchored) Applications Only: four 1/4" flat washers. (See Figure 3) NOTE: Do not perform this step if you are going to anchor the stand to a surface. x 4 1 1. Install five rubber bumpers (B) on bottom of stand. (See Figure 1) 4 x 4 x 4 Rubber Bumpers (5 pla

Resumo do conteúdo contido na página número 6

MSS6000 Installation Instructions Display Installation The following procedure assumes that the proper interface bracket for the display being mounted has already been installed on the display. May remove If no interface bracket is present on display, install pin and nut and 1 bracket to display using the instructions included with the move to lower holes interface bracket before proceeding. If an interface bracket for the display being mounted needs to be obtained, or additional assistance is r

Resumo do conteúdo contido na página número 7

Installation Instructions MSS6000 Remove bolt 1 or padlock Height Adjustment 2 if used 5" Max. Screws (2 each side) Pin in "Closed" position - move to "Open" position to remove display 4 Figure 8 Display Roll Adjustment The MSS-6000 provides limited display roll adjustment Pin in for the purpose of leveling the display. "Open" To level the display: position - move to 1. Loosen upper and lower roll adjustment nuts. "Closed" (See Figure 9) position after display 2. Level display. (See Figure 9) is

Resumo do conteúdo contido na página número 8

MSS6000 Installation Instructions steps 1 through 7 above. Display Swivel Stop Location Adjustment The MSS-6000 allows for the installation of swivel stops that limit the amount of display travel. Stops can be installed at +/-15, 25 or 35 degrees. To install swivel stops: 1. Follow steps 1 through 3 of Display Swivel Tension Adjustment section. 2 deg. Max. 2. Insert one 10-24 X 1/2” Phillips head cap screw in one of the three swivel stop holes (15, 25 or 35 degrees) in the base of the stand. (Se

Resumo do conteúdo contido na página número 9

Installation Instructions MSS6000 Option C Cable Management Option C uses the cable access at the center of the MSS- The MSS-6000 has been designed to provide multiple 6000 and then routes the cables down through an access cable management/routing options. hole or slot in the mounting surface. (See Figure 14) Option A Option A does not use the cable access features of the MSS-600 and simply routes the cables away from the Cable display and mount. (See Figure 12) Access Routed through access hole

Resumo do conteúdo contido na página número 10

MSS6000 Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. 8800-000057 Rev. B 2008 Chief Manufacturing P +86-755-8996 9226 www.chiefmfg.com F +86-755-8996 9217 03/08