Manual do usuário Chief Manufacturing Small Flat Panel In-Wall Swing Arm Mount FWDIW-I Series

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS
Small Flat Panel In-Wall Swing Arm Mount
FWDIW Series

Resumo do conteúdo contido na página número 2

FWDIW Series Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this WARNING: Failure to read, thoroughly understand, and manual accurate and complete. However, Milestone makes no follow all instructions can result in serious personal injury, claim that the information contained herein covers all details, damage to equipment, or voiding of factory warranty! It is the conditions or variation

Resumo do conteúdo contido na página número 3

Installation Instructions FWDIW Series TOOLS REQUIRED FOR INSTALLATION AND PARTS 3/16" (Included) B (4) 2 short (SIDES) 2 long A (1) I/M x1 E (4) C (4) D (4) 1/4" 5/16-18 x 5/8" 5/16" F (1) K (2) J (4) 08 x 1/2" 8-32 x 3/8" G (2) H (2) P (4) N (1) L (12) M (4) 3/16" Q R Q1 (4) Q4 (1) R5 (4) M4x8mm R1 (4) R2 (4) M4x12mm M4x30mm M4x20mm Q2 (6) M4x16mm R3 (4) R4 (4) Q3 (6) .375" .750" 1/8" 3

Resumo do conteúdo contido na página número 4

FWDIW Series Installation Instructions with four mounting holes in FAC501. (See Figure 2) Installation The following procedure assumes that a Chief Model FAC501 In-Wall accessory has previously been installed following the installation instructions provided by the manufaurer. If a FAC501 is not installed or there are any other questions Swing Arm regarding the installation of this accessory, immediately contact Mounting Chief. Bracket 5 WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CA

Resumo do conteúdo contido na página número 5

Installation Instructions FWDIW Series Display Installation The mounting holes on the back of the display will either be flush with the back surface, or recessed into the back surface. Refer to the applicable installation procedure below. 2 Flush Mount Display 3 WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mount

Resumo do conteúdo contido na página número 6

FWDIW Series Installation Instructions lower mounting holes in interface bracket (Q4). Attach Interface Bracket to Display (See Figure 9) 1. Lay display face down on a clean and dry flat surface. 2. Attach Interface Bracket (Q4) to display using six M4x16mm Phillips flat machine screws (Q2) and six 1/8" spacers (Q3). (See Figure 7) 3. Tighten all screws. (Q4) (Q4) (R1) x 4 (Q2) x 6 (Q3) x 6 Figure 9 Figure 7 Cable Management Attach Display to Mount 1. Attach all cables to display. 1. Start two M

Resumo do conteúdo contido na página número 7

Installation Instructions FWDIW Series Trim Installation To install optional trim; 1. Remove paper covering adhesive and affix three tape squares (L) to inside lower flange of each trim piece (B). (See Figure 11) 2. Orient trim pieces (B) as shown in figure below. (See Figure 11) 3. Remove paper covering adhesive back from tape squares (L) on trim and press trim (B) against inner wall of box. (See Figure 11) 2 3 (B) x 4 Figure 12 (L) x 12 To adjust display Roll, Pitch, and YAW tension: Figure 11

Resumo do conteúdo contido na página número 8

FWDIW Series Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands Chief Manufacturing, a division of P +31 (0)40 2668620 Milestone AV Technologies F +31 (0)40 2668615 Asia Pacific A Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. 8805-000240 Rev B 2008 Milestone AV Technologies P +86-755-8996 9226 www.