Resumo do conteúdo contido na página número 1
Model No. 831.153933
Serial No.
Write the serial number in the WEIGHT SYSTEM EXERCISER
space above for reference.
User’s Manual
Serial Number Decal (under seat)
· Assembly
· Adjustments
· Troubleshooting
· Part List and Drawing
Patent Pending
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
Sears, Roebuck and Co., Hoffman Estates, IL 60179
al for future reference.
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ADJUSTMENTS . . . . . . .
Resumo do conteúdo contido na página número 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system. 1. Read all instructions in this manual and in 13. Always disconnect the lat bar from the the accompanying literature before using the weight system when performing an exercise weight system. that does not use the lat bar. 2. It is the responsibility of the owner to ensure 14. Make sure that the cables remain on the pul- that all users of the weight system
Resumo do conteúdo contido na página número 4
BEFORE YOU BEGIN ® ® Thank you for selecting the versatile WEIDER PRO reading this manual, call 1-800-4-MY-HOME ® 4850 weight system. The WEIDER PRO 4850 weight (1-800-469-4663). To help us assist you, please note system offers an impressive array of weight stations the product model number and serial number before designed to develop every major muscle group of the calling. The model number is 831.153933. The serial body. Whether your goal is to tone your body, build number can be found on a de
Resumo do conteúdo contido na página número 5
ASSEMBLY Make sure that you have the following tools: Make Assembly Easier • Two adjustable wrenches Everything in this manual is designed to ensure that the weight system can be assem- • One standard screwdriver bled successfully by anyone. • One phillips screwdriver Before beginning assembly, make sure to • One rubber mallet read the information on this page. This brief introduction will save you much more •You will also need grease or petroleum jelly, a time than it takes to read it. sm
Resumo do conteúdo contido na página número 6
1 FRAME ASSEMBLY 1. Make sure that you understand all of the 71 85 information on page 5 before you begin assembling the weight system. 120 110 86 Locate and open the parts bags labeled “FRAME 2 ASSEMBLY 1” and “FRAME ASSEMBLY 2.” 86 Press a 2” Square Inner Cap (105) into the open end of the Long Base (120). 110 110 110 Insert eight 5/16” x 2 1/2” Carriage Bolts (110) up 105 through the Long Base (120) and the Short Base (2) 2 110 as shown. Note: It may be helpful to place tape 53 over the head
Resumo do conteúdo contido na página número 7
4. Press a 1 1/2” Square Inner Cap (67) into the 4 square tube on the Butterfly Upright (3). Slide the Butterfly Upright (3) onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Short Base (2). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. 67 3 86 86 2 110 5. Press a 2” x 3” Inner Cap (58) into the top of the 5 Seat Upright (9). Attach the Leg Lever Bumper (77) 58 to the Seat Upright with a #10 x 1” Screw (14). 9 Slide the
Resumo do conteúdo contido na página número 8
7. Press a 2” x 3” Inner Cap (58) into the top of the 7 Squat Upright (4). Slide the Squat Upright onto the 58 two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Long Base (120). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt. Do not tight- en the Nylon Locknuts yet. 58 5 Press a 2” x 3” Inner Cap (58) into the top of the Swivel Upright (5). Slide the Swivel Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Long Base (120). Finger tighten a 5/16”
Resumo do conteúdo contido na página número 9
9. Attach a Roller (39) and two 5/16” Washers (90) 9 39 between the indicated set of holes in the Squat Slider (38) with a 5/16” x 3 1/2” Bolt (94), two 5/16” Washers (90), and a 5/16” Nylon Locknut (86) as 38 shown. 39 86 Assemble the other three Rollers (39) to the 90 Squat Slider (38) in the same manner. 90 94 90 90 39 10. Slide the Squat Slider (38) down onto the Squat 10 Upright (4). 38 4 11. Insert the ends of two Weight Guides (42) into the 11 indicated bracket on the Long Base (120). S
Resumo do conteúdo contido na página número 10
12. Attach the Top Frame (6) between the Squat Upright 12 (4) and the Swivel Upright (5) with four 5/16” x 3 3/4” Bolts (92), the two Short Frame Plates (52), and two 6 5/16” Nylon Locknuts (86) as shown. Do not tighten 52 92 the Bolts and Locknuts yet. 86 87 Attach the four Weight Guides (42) to the Top Frame 86 (6) with two 3/8” x 6 1/2” Bolts (95) and two 3/8” Nylon Locknuts (87). 5 42 95 87 52 95 92 4 13. Press two 2” x 3” Inner Caps (58) into the Top Frame 92 13 (6) and the Butterfly Top Fr
Resumo do conteúdo contido na página número 11
16. Press a 1 1/2” x 2” Inner Cap (21) into the Right 16 Lubricate Butterfly Arm (26). Wet the lower end of the Arm with 100 soapy water. Slide a Long Pad (54) onto the Arm. 26 70 Slide two Nut Clips (108) onto a Press Handle (27). 113 Attach the Press Handle to the Right Butterfly Arm (26) with two 5/16” x 3/4” Button Head Screws (51). 21 51 Slide the Long Pad (54) down so that the bottom is flush with the lower end of the Arm. Press a 1” Round Inner Cap (29) into the Press Handle. Wet 25 54 th
Resumo do conteúdo contido na página número 12
19. Route the Swivel High Cable (74) through the Swivel 19 18 Upright (5) and over a 4 1/2” Pulley (119). Attach the 91 5 Pulley inside the Upright with a 3/8” x 2 3/4” Bolt 101 (101), two 3/8” Washers (91), two 1/2” Spacers (89), 91 and a 3/8” Nylon Locknut (87). 91 87 89 91 Attach a 3/8” x 2 1/2” Bolt (18), two 3/8” Washers (91), and a 3/8” Nylon Locknut (87) to the Swivel 74 89 87 Upright (5). 119 20. Remove the preattached 3 1/2” Pulleys (78) from 20 the Small Pulley Plates (31). 74 Wrap the
Resumo do conteúdo contido na página número 13
24. Remove the preattached 3 1/2” Pulleys (78) from 24 the Offset Double “U”-bracket (61). Wrap the Swivel Cable (17) around a 3 1/2” Pulley 17 (78). Attach the Pulley to the Offset Double “U”- 78 bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” 93 Nylon Locknut (87). 87 61 25. Wrap the Swivel Cable (17) around a 3 1/2” Pulley 25 (78). Attach the Pulley and a Cable Trap (68) to the next to bottom hole in the Small Pulley Plates (31) 31 with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut 1
Resumo do conteúdo contido na página número 14
29. Wrap the Lat Cable (88) around a 3 1/2” Pulley 29 88 (78). Attach the Pulley and a Long Cable Trap (102) 78 113 to the Top Frame (6) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Jamnut (113). Make sure the 102 Cable Trap is turned to hold the Cable in the 93 groove of the Pulley. 6 30. Remove the preattached 3 1/2” Pulleys (78) from 30 the Pulley Plates (63). 100 68 Wrap the Lat Cable (88) around a 3 1/2” Pulley 78 (78). Attach the Pulley and a Cable Trap (68) to the second set of holes f
Resumo do conteúdo contido na página número 15
34. Remove the preattached 3 1/2” Pulleys (78) from 34 the Double “U”-bracket (62). 69 Wrap the Butterfly Cable (69) under a 3 1/2” Pulley 78 (78). Attach the Pulley to the Double “U”-bracket (62) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 87 93 62 35. Wrap the Butterfly Cable (69) over a “V”-pulley (55). 35 18 Attach the Pulley and a Long Cable Trap (102) to the other bracket on the Butterfly Upright (3) with a 102 3/8” x 2 1/2” Bolt (18) and a 3/8” Nylon Locknut 69 (87). Mak
Resumo do conteúdo contido na página número 16
39. Route the Leg Lever Cable (75) under a 4 1/2” 39 Pulley (119). Attach the Pulley and a Large Cable Trap (121) to the indicated side of the Butterfly 119 Upright (3) with a 3/8” x 3 3/4” Bolt (122), a 3/8” 122 Washer (91), and a 3/8” Nylon Jamnut (113). Make 121 sure that the Large Cable Trap is turned to hold the Cable in the groove of the Pulley. 3 75 113 91 40. Wrap the Leg Lever Cable (75) over a 3 1/2” Pulley 40 (78). Attach the Pulley to the Double “U”-bracket (62) with a 3/8” x 1 3/4”
Resumo do conteúdo contido na página número 17
44. Wrap the Swivel Low Cable (72) over a 3 1/2” Pulley 44 (78). Attach the Pulley to the Offset Double “U”- 87 93 bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” 61 Nylon Locknut (87). 78 72 45. Wrap the Swivel Low Cable (72) under a 3 1/2” 45 Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt 72 (93) and a 3/8” Nylon Locknut (87). 78 87 120 93 46. Route the Swivel Low Cable (72) under the indicat- 46 ed stack of Weights (44). 72 78
Resumo do conteúdo contido na página número 18
49. Wrap the Swivel Low Cable (72) over a 3 1/2” 49 Pulley (78). Attach the Pulley and a Cable Trap (68) between the lower set of holes in the “U”-bracket (64) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable Trap is 100 turned to hold the Cable in the groove of the 64 Pulley. 68 87 72 78 50. Attach the end of the Swivel Low Cable (72) inside 50 of the Short Base (2) with a 5/16” x 2 1/2” Bolt (59), two 5/16” Washers (90), and a 5/16” Nylon Locknut (86). 86 90
Resumo do conteúdo contido na página número 19
53. Wrap the Squat Cable (73) under a 3 1/2” Pulley 53 (78). Attach the Pulley and a Cable Trap to the sec- ond set of holes from the top in the indicated brack- et on the Long Base (120) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable Trap is turned to hold the Cable in the groove of the Pulley. 73 78 68 87 100 120 54. Wrap the Squat Cable (73) over a 4 1/2” Pulley 54 (119). Attach the Pulley to the indicated bracket on 6 87 the Top Frame (6) with a 3/8” x 1
Resumo do conteúdo contido na página número 20
57. Attach the Seat (16) to the Seat Frame (8) with two 57 1/4” x 3/4” Screws (114), a 1/4” x 2 1/2” Screw (99), 16 and a 1/4” Washer (97). 8 97 114 99 58. Attach the Butterfly Backrest (15) to the Butterfly 58 Upright (3) with two 1/4” x 3 1/2” Screws (128) and two 1/4” Washers (97). 128 97 15 3 97 128 59. Wet one end of the Squat Arm (32) with soapy 59 water. Slide a Short Pad (20) onto the Squat Arm 20 32 as shown. Slide two Nut Clips (108) onto a Squat Handle (33). 51 Attach the Squat Handle
