Руководство по эксплуатации ACTiSYS ACT-IR100S

Краткое содержание страницы № 1



  





 



 










  
     
! 
"#"$

%&'"( !)%&' #(* 
+(,% (

 -./.














0
1%222./.     , .3

Краткое содержание страницы № 2

!456 . This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING-FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user authority to operate this

Краткое содержание страницы № 3

 

 70+
$689# 8   7 %!.&0:0 ' 66 ;
8  , 60(#

Краткое содержание страницы № 4

  
  To ensure trouble-free operation, please observe the following precautions: Optical communications are easily affected by external light sources, weak batteries, transfer distance, transfer angle, etc. Any of these conditions may cause a data transfer failure, incomplete, missing or incorrect data. Make sure that the wireless interface is away from direct sunlight and other strong light source. !"Do not terminate arbitrarily during file transfer process between DUT an

Краткое содержание страницы № 5

 
 

  


  
 
 



Here the settings for the R11 ~ R18 are displayed. When power is thrown for any resistor besides R13~R15, they will be sampled at the time NMI is reinstated. After that, there will be no problems with operation even if the settings are changed; however the settings will become invalid. 






PCB bottom view 


0
  
R11

Краткое содержание страницы № 6





 
 
 
It is possible to select the primary channel mode, secondary channel mode, and the primary channel as well as the secondary channel according to the settings of R11 and R12. Operation mode mode setting terminal R11 R12 Reservation 0R 0R  primary channel 0R secondary channel 0R    Primary / secondary channel




! " #
#  

 
It is possible to set the RS-232C communication speed with R13, R14, and R15.

Краткое содержание страницы № 7



$%
  
 
In order to confirm that the device is operating correctly there is an indicate function installed. By looking at the flash of the LED you can check the state of communication. There are 2 flashing speeds, during standby on the secondary channel there is no flashing. If the primary channel commences discovery, it will flash once every 3 seconds (for approx. 0.7 seconds). After discovering the other device and communication becomes possible it will flash ev

Краткое содержание страницы № 8


&
' (

 
● Serial Port: When connecting modems etc. to the Data Communication Equipment (DCE) side, connect the corresponding signal names of the modem and IR100S+. When connecting to PC’s to the Data Terminal Equipment (DTE) side use a cross connection for IR100S+ and the PC or Plotter/Printer(with RS232 port). Example Connection Reference #1: Modem (DCE) Connection IR100S+ I/F < Straight Cable > Modem(DCE) RxD RxD : Data Receiving

Краткое содержание страницы № 9

Example Connection Reference #2: PC Terminal (DTE) Connection IR100S+ I/F < Cross Cable > PC Terminal(DTE) RxD RxD : Data Receiving (RD) (RD) Only valid with received data when the DCD (CD) signal is on. TxD TxD : Data Transmission (SD) (SD) Valid with sending data when RTS (RS), CTS (CS), DSR (DR), DTR (ER) are on. /DTR / DTR : Data Terminal Ready (ER

Краткое содержание страницы № 10

    
  Product Name: ACT-IR100S Compatibility: Fully compatible with IrDA -1.0 Physical spec. and IrDA-1.0 protocol spec.: IrLAP, IrLMP, IAS, TinyTp, IrCOMM Specifications of IrDA-1.0 (SIR): Transmission Speed 9.6kbps, 19.2kbps, 38.4kbps, 57.6kbps, 115.2kbps Communication within 100cm Distance Radiating Angle ±15º~±30º (±15 to ±30 degrees) Peak Wave Length of 880~1050nm Radiated Light Specifications of RS-232 port: Transmission

Краткое содержание страницы № 11

77+9;6?
%
60+69>@;+,890
689708+;$0+

) * 
 
Many PC peripherals use serial cable to communicate with PC. They cannot talk with Infrared Devices, such as IrDA capable PC, notebooks. ACT IR-100S’s aim is to make those devices into IrDA compatible product by simply connecting it to their serial port. And these devices with IR100S COM-port IrDA bridge can communicate with PC wirelessly and don't need to modify neither hardware nor software This sim

Краткое содержание страницы № 12

,-)
,-
  

  
  
 
  



()
''
)!
*+

  
!"


$

%& $

   #


"
# +  
PC#1: Install IrDA Driver. The assigned IR virtual port must be COM4 or less, otherwise HyperTerminal will not be able to connect it IR Monitor: Speed limit = 115.2K or lower HyperTerminal: Connect Using -> direct to COM4 (assign

Краткое содержание страницы № 13

Communicating with Name: ACTiSYS IR100S-115 (Nickname of 100s, might be different with different version) Description: Intelligent SIR Adapter Communication efficiency (…) Good at 115.2 Kbps (or 57.6 Kbps. Depends on the highest speed both sides can support) 5. Run HyperTerminal on PC#1 now. Set its properties according to the above configuration guide. Click the Call icon to connect to the assigned IR port. The LED DSR and CTS of the RS232 Mini Tester on PC#2 side shoul

Краткое содержание страницы № 14

Figure A-3 Figure A-4


Краткое содержание страницы № 15

Figure A-5 Figure A-6


Краткое содержание страницы № 16

77+9;6?%$60.  ,2 6 ;
, 
) * 
 
If your device has no built-in modem and wants to connect to Internet, normally you will buy an external modem and use cable to connect them together. But some mobile devices are so small that have no RS-232 port for cable connection. Most of them have IrDA wireless built-in interface so that they can connect with an IrDA modem without cable. One usage of ACT IR-100S is to make those n

Краткое содержание страницы № 17

&

  
 

 


+,
%%
()
* !
&'
%
 !


"

#$ "

    "
# +  

Connect all devices as Fig B-1. PC: Install IrDA Driver. Configure the Modem: (Fig B-2..6) Port: Virtual Infrared COM Port Maximum Speed: 115.2 Kbps Data bits-Parity-Stop bits: 8-N-1 Use flow control: Hardware (RTS/CTS) 100S: R11-18 or DSW8-1: 1

Краткое содержание страницы № 18




































































































































Краткое содержание страницы № 19











































































Краткое содержание страницы № 20


!