ملخص المحتوى في الصفحة رقم 1
REVISED 11/3/98
1
User’s Manual for
900 MHz Cordless Caller ID/
Call Waiting 9340
Part 2
Please read Part 1 — Important Product
Information, included in your package.
AT&T 9340 cover_1ATT 3 11/3/98, 12:45 PM
ملخص المحتوى في الصفحة رقم 2
© 1998 Philips Consumer Communications L.P. All rights reserved. Printed in Mexico. COMCODE Issue 1AT&T AT&T 9340 cover_1ATT 2 11/3/98, 12:45 PM
ملخص المحتوى في الصفحة رقم 3
CONTENTS INSTALLATION................................. 3 TELEPHONE MEMORY ....................14 Belt Clip ................................................ 5 Memory Guard .................................... 14 Storing Numbers In Memory .............. 14 FEATURE SETUP.............................. 6 Storing a Name with a Number........... 14 About Softkeys ...................................... 6 Replacing a Stored Number ................ 15 Dial Mode ............................................
ملخص المحتوى في الصفحة رقم 4
2 AT&T 9340 book_1ATT 2 11/3/98, 12:39 PM
ملخص المحتوى في الصفحة رقم 5
INSTALLATION Standard Modular electrical telephone outlet jack Strain-relief groove Long telephone line cord Power cord The instructions below are for both table and wall installation. 1 Choose a spot near an electrical outlet and a telephone jack. This phone requires a modular telephone jack and a standard electrical outlet (110v AC) not controlled by a wall switch. 2 Install the handset battery. (For an illustration of battery installation, see the BATTERIES section in this manual.) • Remove t
ملخص المحتوى في الصفحة رقم 6
INSTALLATION 5 Mount the base on the wall. (WALL MOUNTING ONLY) Modular telephone jack Short telephone line cord Standard electrical outlet Power cord 6 Charge the handset batteries for six hours. Place the handset face up or face down in the base. The CHARGING/HANDSET IN USE light on the base goes on to show the handset is in the right position to charge the batteries. 7 Check for dial tone. After the batteries are charged, pick up the handset. Check for a dial tone by pressing P; you should
ملخص المحتوى في الصفحة رقم 7
INSTALLATION Belt Clip If you wish, you can attach the belt clip to the cordless handset, following the illustrations below. (The handset cannot be charged in the face-up position if the belt clip is attached.) To Attach To Remove 5 AT&T 9340 book_1ATT 5 11/3/98, 12:40 PM
ملخص المحتوى في الصفحة رقم 8
FEATURE SETUP You can set up one feature at a time as described below, or you can set up a feature, and then move on to set up another feature. After you change one feature, press U to exit, or select the DONE softkey to move to the next feature. About Softkeys This telephone has been designed with your convenience in mind, offering you many features which you can access using the two “softkeys” shown in the illustration. Press U to begin viewing options. Use < and > to scroll through the cho
ملخص المحتوى في الصفحة رقم 9
FEATURE SETUP Ringer Off / Battery Save When the Ringer is set to OFF, the handset stays ready to use for up to 30 days in the standby mode before you have to return it to the base for recharging. When the Ringer is off, the Page/Handset Locator feature does not work, and the screen does not display incoming call information. However, the call information is stored in the call history. The Ringer Off Icon, , is displayed only when the phone is on. When the Ringer is on, the handset stays ready
ملخص المحتوى في الصفحة رقم 10
FEATURE SETUP Programming Home and Local Area Codes Your “home area code” is the area code from which you are dialing. Numbers called within your home area code do not require you to dial a “1” or the area code before dialing the telephone number. “Local area codes” are area codes that require no “1” before dialing the telephone number; however, the area code must be dialed. Always program your home area code, and, if you need them, your local area codes (up to four). Programming these area co
ملخص المحتوى في الصفحة رقم 11
FEATURE SETUP Call List Options You can customize how the phone stores call information. Select whether the system stores information about ALL CALLS received, or for NO CALLS. The system comes set to ALL CALLS. 1 Make sure the is not displayed. 2 Press U >. 3 Use the softkey to select SETUP. 4 Select DONE until the screen displays LIST:ALL CALLS. 5 Select CHANGE to display ALL CALLS or NO CALLS. 6 Select DONE to move to the next feature — OR — Press U to exit. Message Waiting Indicator If y
ملخص المحتوى في الصفحة رقم 12
TELEPHONE OPERATION Antenna L1 L2 Softkey Softkey Access special Scroll through programming features screen information Make or Dial number answer a call displayed on screen Access subscriber services Temporary Tone Change channel Adjust handset volume Making a Call 1 Press P, and wait for to appear on the display. As the phone is selecting a channel, the screen may display SEARCHING.... 2 When you hear a dial tone, dial the number. 3 See the TELEPHONE MEMORY and CALLER ID sections of this ma
ملخص المحتوى في الصفحة رقم 13
TELEPHONE OPERATION Answering a Call Press P on the handset. The appears and the call is connected. Ending a Call Press P on the handset. The disappears. — OR — Place the handset in the cradle. Redial The last number dialed on this phone (up to 24 digits) is stored in redial memory until you dial another number. 1 Press P. 2 Wait for the dial tone and for the to appear. 3 When you hear a dial tone, use the softkey to select REDIAL. (REDIAL does not appear on the screen if there is no number
ملخص المحتوى في الصفحة رقم 14
TELEPHONE OPERATION most special services; however, some services may actually require a touch tone line. To be sure, ask the company that provides the special service. 1 Dial the call, then press *. Any buttons pressed after this send tone signals. 2 When you hang up or press F, the phone automatically returns to dial pulse (rotary) dialing. Mute Mute allows you to hear your caller, but prevents the caller from hearing you. 1 Press > while on a call, until the screen displays MUTE; select MUT
ملخص المحتوى في الصفحة رقم 15
TELEPHONE OPERATION Changing Channels This cordless telephone has an advanced AutoSelect feature that minimizes the chance of interference. When the phone is looking for a clear channel, the screen displays SEARCHING.... If it is unable to locate a clear channel, the screen displays TRY AGAIN. Hang up and try your call again. In the unlikely event that you notice noise or interference while using the handset: 1 Press h. 2 If the interference does not clear, move closer to the base and press h
ملخص المحتوى في الصفحة رقم 16
TELEPHONE MEMORY You can store up to 10 telephone numbers and names in memory. The telephone memory works with the Memory Match and Priority Ring features. When you receive a call from a number you’ve stored in memory, the screen displays the name information as you’ve stored it, not as the service sends it (for example, “MOM AND DAD”). Additionally, the phone alerts you to calls from priority numbers you’ve stored in memory with a special Priority Ring. For more information about these featur
ملخص المحتوى في الصفحة رقم 17
TELEPHONE MEMORY Replacing a Stored Number You can replace a stored number by storing a new number in its place. Follow the directions for “Storing Numbers in Memory.” Storing a Pause in a Memory Number While storing a memory number (see “Storing Numbers in Memory”) use the softkey to select PAUSE where you want dialing to pause for two seconds. Storing a Number and Name from call history in Telephone Memory You can store information received from Caller ID in the telephone memory. (See CALLER I
ملخص المحتوى في الصفحة رقم 18
TELEPHONE MEMORY Priority Ring Numbers When you view a number stored in memory, you can label it so that when a call is received from that number, the handset alerts you with a special ring that this is a priority call. The special ring begins after the first normal ring on the line. 1 While viewing numbers in memory, use < or > to scroll to the desired location. 2 Press * to activate Priority Ring for the displayed number (the screen displays ! ). To deactivate Priority Ring, press #. Dialing
ملخص المحتوى في الصفحة رقم 19
CALLER ID OPERATION Unreviewed Call Repeat Call information Battery status Ringer Voice information indicator Priority Call is off Mail L1 L2 Date Phone in use Call Number Time Caller’s Number Caller’s Name About Caller Identification This telephone has a Caller ID feature that works with Caller Identification service provided by your local telephone company. There is a fee for this service, and it may not be available in all areas. This phone can provide information only if both you and the c
ملخص المحتوى في الصفحة رقم 20
CALLER ID OPERATION Incoming Call History This telephone assigns each incoming call a number from 1 to 99. The most recent call will have the highest number (for example, if 10 calls have been received, call number 10 is the most recent, and call number 1 is the oldest). When the call history is full, the oldest call information is deleted to make room for new incoming call information. Reviewing Call History You can review information in the call history at any time by pressing either < or >,
