ملخص المحتوى في الصفحة رقم 1
Preparation Basics Caller ID/Call waiting
Answering System Additional Information
SG-1991.qxd 7/4/1 7:29 PM Page 1
,
OWNER S MANUAL
2.4GHz DIGITAL SPREAD SPECTRUM CORDLESS TELEPHONE
DIGITAL ANSWERING SYSTEM
-
SG 1991
The FIRST thing to do after unpacking your new
cordless telephone is:
CHARGE THE BATTERY !
Please read and follow the few instructions on
PAGE 2
BEFORE YOU DO ANYTHING ELSE.
ملخص المحتوى في الصفحة رقم 2
SG-1991.qxd 7/4/1 7:29 PM Page 2 GETTING STARTED: DO THIS FIRST! FIRST, CHARGE THE HANDSET BATTERY! • Set your new phone in an out-of-the-way place near a power outlet where it will not be disturbed. • Plug the AC adaptor into the wall outlet. • Plug the AC adaptor cord into the power jack on the base unit. • Take the cover off the handset battery compartment; plug the battery connector into the receptacle inside the battery compartment and replace the cover. The connector only goes in one wa
ملخص المحتوى في الصفحة رقم 3
Preparation DIGITAL CALLER ID / ANSWERING SYSTEM CORDLESS TELEPHONE SG-1991.qxd 7/4/1 7:29 PM Page 3 INTRODUCTION FEATURES Toshiba America Consumer Products, Inc., takes pride in presenting the new 2.4 GHz cordless telephone and digital answering system. The Toshiba cordless telephone features a 16-digit x 3-line dot matrix liquid crystal display (LCD) for caller ID on Call Waiting and speed dial programming and calling. The sleek new design provides face-up battery charging even when wall mo
ملخص المحتوى في الصفحة رقم 4
SG-1991.qxd 7/4/1 7:29 PM Page 4 TABLE OF CONTENTS Preparation INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . .6 LOCATION OF CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 5
SG-1991.qxd 7/4/1 7:29 PM Page 5 TABLE OF CONTENTS Steps for entering names and special characters . . . . . . . . . . . . . . .28 If you make a mistake while entering a name . . . . . . . . . . . . . . . . . .29 Storing numbers at the base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Dialing a stored number at the handset . . . . . . . . . . . . . . . . . . . . . .30 Dialing a stored number at the base unit . . . . . . . . . . . . . . . . . . . . .30 Editing and deleting stor
ملخص المحتوى في الصفحة رقم 6
SG-1991.qxd 7/4/1 7:29 PM Page 6 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, 9 Never push objects of any kind into this product through cabinet slots as basic safety precautions should always they may touch dangerous voltage be followed to reduce the risk of fire, points or short out parts that could electric shock and injury. result in a risk of fire or electric shock. 1 Read and understand all instructions. Never spill liquid of any kind on the 2 Follow all warnings an
ملخص المحتوى في الصفحة رقم 7
Preparation SG-1991.qxd 7/4/1 7:29 PM Page 7 IMPORTANT SAFETY INSTRUCTIONS TM The RBRC Seal TM The RBRC Seal on the (easily removable) nickel-cadmium battery (contained in our product) indicates that Toshiba America Consumer Products, Inc. (TACP) is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, TM when taken out of service within the United States. The RBRC program provides a convenient alternative to placing used nic
ملخص المحتوى في الصفحة رقم 8
SG-1991.qxd 7/4/1 7:29 PM Page 8 LOCATION OF CONTROLS HANDSET Antenna VOL (VOLUME/RINGER) button Headset jack (Up arrow button) VOL (VOLUME/RINGER) button (Down arrow button) (page 20 to MEM (Memory) button (page 26 to 32) 21, 31 to 40) CID (Caller ID) button (page 34 to 38) TALK button (page 18 to 19) CID L.D./1 button (page 36) FLASH button (page 39) L.D. LOCAL button (page 36) LOCAL/3 TONE/ (TONE) button (page 21) ( ) button (Left arrow button) # ( ) button (Right arrow button) (page
ملخص المحتوى في الصفحة رقم 9
Preparation IN USE SPEAKER CHARGE MUTE TIME PIN VOLUME DELETE PLAY / STOP REPEAT SKIP MEMO GREETING / 2 WAY REC ANSWER MEMORY REDIAL / PAUSE TONE FLASH MUTE INTCOM SPEAKER DIGITAL CALLER ID / ANSWERING SYSTEM CORDLESS TELEPHONE MIC SG-1991.qxd 7/4/1 7:29 PM Page 9 LOCATION OF CONTROLS BASE UNIT IN USE/CHARGE LED SPEAKER/MUTE LED PIN button (page 44) Antenna TIME button (page 43) DELETE button (page 46 to 47) Speaker GREETING button (page 45 to 46) VOLUME buttons (page 46) REPEAT LED display
ملخص المحتوى في الصفحة رقم 10
SG-1991.qxd 7/4/1 7:29 PM Page 10 INSTALLATION SETTING UP THE BASE UNIT (DESK TOP MOUNTING) For setting up the base unit follow the instructions below. Snap the bracket’s tab into the notches on the base. Fasten the AC adaptor cord to prevent it from being disconnected. Raise the antenna to Single-Line vertical Telephone Jack position. Telephone Line Cord (RJ11C) Power Outlet (AC 120 V, 60 Hz) AC Adaptor • Plug the AC adaptor firmly into the base unit and the AC 120V outlet. • USE ONLY WITH S
ملخص المحتوى في الصفحة رقم 11
Preparation SG-1991.qxd 7/4/1 7:29 PM Page 11 INSTALLATION SETTING UP THE BASE UNIT (WALL MOUNTING) MOUNTING ON A STANDARD WALL PLATE: Insert the bracket’s tabs into the base’s lower tab slots, then press down on the top of the bracket to snap it into the clip slots. Flip the hook tab over Raise the antenna. so the tab holds the handset. Single-Line Telephone Jack (RJ11C) Power Outlet (AC 120 V, 60 Hz) • Route the cords through the guides. AC Adaptor • Place the base unit on the posts of the
ملخص المحتوى في الصفحة رقم 12
DIGITAL CALLER ID / ANSWERING SYSTEM CORDLESS TELEPHONE SG-1991.qxd 7/4/1 7:29 PM Page 12 INSTALLATION CHARGING THE BATTERY PACK It is important to charge the battery for 12-16 hours continuously without any interruption before you use the handset for the first time. Black Red 1 Remove the battery cover on the back of the handset by sliding it down. 2 Plug the battery pack cord into the connector with the correct polarity. (black and red wires). 3 Place the battery pack in the battery compart
ملخص المحتوى في الصفحة رقم 13
Preparation SG-1991.qxd 7/4/1 7:29 PM Page 13 INSTALLATION NOTES: • Use only the supplied battery pack (TRB-1981 power source 800mAh, 3.6VDC) • The battery pack is not charged properly if the charging contacts are dirty or tarnished. Clean the contacts occasionally with a dry cloth. After the battery pack is fully charged; Operation Approx. battery life While in use (Talk mode) up to 6 hours While not in use (Standby mode) up to 10 days When "Low Battery" blinks on the LCD, all handset button
ملخص المحتوى في الصفحة رقم 14
SG-1991.qxd 7/4/1 7:29 PM Page 14 INSTALLATION Before using the Handset, make sure to read the following instructions. VOL () VOL () FUNCTION SELECT / CHANNEL SETTING THE TONE/PULSE SWITCH Set the TONE/PULSE switch to TONE. Place a call. If the call does not connect with the TONE setting, set the TONE/PULSE switch to PULSE. TONE/PULSE switch 14 Preparation
ملخص المحتوى في الصفحة رقم 15
Preparation SG-1991.qxd 7/4/1 7:29 PM Page 15 INSTALLATION SETTING OR CANCELING THE AUTO TALK FUNCTION If the handset is placed on the base unit, you can answer a call by lifting the handset from the base unit (Auto Talk). If the handset is not on the base unit, you can answer a call by pressing any one of the buttons (Any-key Answer function). When the Auto Talk function is set to ON, the Any-key Answer function is also set to ON. When the Auto Talk function is set to OFF, you can lift the h
ملخص المحتوى في الصفحة رقم 16
SG-1991.qxd 7/4/1 7:29 PM Page 16 INSTALLATION SETTING THE AREA CODE It is necessary to program your area code so that local calls will be displayed properly on caller ID. 1s sAuto Talk:Off 2 CIDCW :On 1Press . FUNCTION 3 Area Code: 1 Auto Talk:Off 2 CIDCW :On 3 2 Press or to move the pointer to Area 3s sArea Code: Code. 1 Auto Talk:Off 2 CIDCW :On SELECT/CHANNEL 3Press . 3 Area Code:615 Enter your 3-digit area code. For example, enter “615.” If you enter a wrong number, press DELETE . 1 A
ملخص المحتوى في الصفحة رقم 17
Preparation SG-1991.qxd 7/4/1 7:29 PM Page 17 INSTALLATION USING THE HEADSET AND BELT CLIP (OPTION) For purchase of an optional accessory, please call 1-877-644-7373. HEADSET You can use an optional headset (part#: RC008260) that has a 3/32- inch (2.5mm) plug. To connect the headset, open the rubber cover on the left side of the handset, then insert the headset's plug into the jack. With a headset connected, you can make or answer calls as usual using the keys on the handset. When you finish u
ملخص المحتوى في الصفحة رقم 18
DIGITAL CALLER ID / ANSWERING SYSTEM CORDLESS TELEPHONE SG-1991.qxd 7/4/1 7:29 PM Page 18 BASIC OPERATION Before using the Handset and Base, make sure to read the following instructions. RINGER ON/OFF switch VOLUME VOL/RING () FLASH TALK VOL/RING () REDIAL/PAUSE TONE/ / / SPEAKER RDL/P DELETE INTCOM / INTCOM MUTE MAKING A CALL Handset Off The Base Handset On The Base 1) Press TALK . 1) Pick up the handset. 2) Listen for the dial tone. 2) Press TALK . 3) Dial the number. 3) Listen for the dia
ملخص المحتوى في الصفحة رقم 19
Basics SG-1991.qxd 7/4/1 7:29 PM Page 19 BASIC OPERATION RECEIVING A CALL With the handset Handset On The Base Handset Off The Base TALK Pick up the handset (AutoTalk) or press . Press any button (Any-Key Answer) or press TALK . TALK To hang up: Press , or return the handset to the base (Auto Standby). NOTE: To use Any-key Answer and Auto Talk functions, set the Auto Talk to ON (See page 15). With the Base speakerphone Press . SPEAKER To hang up, press SPEAKER . SWITCHING FROM THE SPEAKERPHON
ملخص المحتوى في الصفحة رقم 20
SG-1991.qxd 7/4/1 7:29 PM Page 20 BASIC OPERATION REDIAL FROM THE BASE To dial the last number that you called on the base unit: 1Press . SPEAKER 2 Wait for the dial tone. 3 Press REDIAL/PAUSE . INTERFERENCE OR STATIC Static interference can be caused by many different things, such as cordless phones in neighboring homes or apartments, microwave ovens, certain kinds of lighting, etc. If you hear noise during a call, press Talk 0:15 SELECT/CHANNEL to select another channel. Scanning The LC
