ملخص المحتوى في الصفحة رقم 1
uniden@
XC630 - BLACK
XC633 - WHITE
Cordless Telephone
~
Operating Guide
For Australia and New Zealand
ملخص المحتوى في الصفحة رقم 2
2
ملخص المحتوى في الصفحة رقم 3
PRECAUTIONS Before you read anything else, Please observe the following: W ARNIN G ! rniden Corporation DOES NOT represent this unit to be raterproof. To reduce the risk of fire, electrical shock, or amage to the unit, DO NOT expose this unit to rain or 10isture. NICKEL METAL HYDRIDE BATTERY WARNING . This equipment contains a Nickel-Metal Hydride Battery. . The Nickel Metal Hydride Battery contained in this equipment may explode if disposed of in a fire. . Do not short circuit the battery . Do
ملخص المحتوى في الصفحة رقم 4
TABLE OF CONTENTS IMPORTANT SAFETYINSTRUCTIONS 5 ABOUTYOURCORDLESS TELEPHONE 7 UNPACKING 7 XC630/633 FEA TURES 8 ROLLINGDIGITALCODE SECURITY 8 BASE UNIT CONTROLS & FUNCTIONS 9 HANDSET CONTROL & FUNCTIONS 10 READ THIS BEFORE INSTALLATION 12 OVERVIEW ..13 IMPORTANT INFORMATION 13 INSTALLING YOUR CORDLESS TELEPHONE 14 SELECTINGTHEINSTALLATION LOCATION 14 CONNECTINGTHETELEPHONELiNE 14 INSTALLING THETELEPHONEON A DESK ORTABLETOP 15 MOUNTINGTHETELEPHONEON A WALL 16 INSTALLING THE BATTERYPACK 17 CHARGI
ملخص المحتوى في الصفحة رقم 5
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning. 4. Do not use this product near water; for ex
ملخص المحتوى في الصفحة رقم 6
12. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power supply cord is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damag
ملخص المحتوى في الصفحة رقم 7
About your Cord less Telephone Congratulations on your purchase of this Uniden XC630/633 Cordless Telephone. The XC630/633 is designed and engineered to exact standardsfor reliability, long life, and outstanding performance. To get the most from your XC630/633, please read this Operating Guide thoroughly. Unpacking Your XC630/633 box should contain the following items: . Base Unit . Handset . Telephone Line Cord with Modular Plug . AC Adaptor . Recharger Battery Pack . This Operating Guide (read
ملخص المحتوى في الصفحة رقم 8
XC630/633 Features . UltraClear Plus noise reduction provides the best quality sound of a cordless telephone . 2530/39 MHz Channels (NZ) or 1030/39 MHz Channels (AUS) . 10 Number Memory . Maximum Operating Range . 1 way paging . Redial and Flash . Auto Standby . Tone/Pulse Dialing (Australian models Only) . Automatic Digital Code Security . Handset Volume Control Rolling Digital Code Security Many cordless telephones operate similarly and on the same frequency. Without digital code security, ano
ملخص المحتوى في الصفحة رقم 9
Base Unit Controls & Functions BASE ANTENNA PAGE IN USE LED CHARGE LED 9VDC INPUT JACK TONE/PULSE SWITCH / TEL LINE TONE/PULSE Use to select either Tone Dialing or Pulse Dialing. Switch (Functional on Australian Models only) TEL LINE Jack Plug a standard telephone line cord into this jack and the other end of the cord into the standard telephone socket. Plug the AC Adaptor cord into this Jack. Then plug the DC Input Jack AC Adaptor into a standard wall outlet. Base Unit Telescopic antenna provid
ملخص المحتوى في الصفحة رقم 10
Handset Control & Functions HANDSET ANTENNA 1.TALK INDICATOR 2. FLASH 6. MUTE 7. REDIAL 3.TALK 8. MEMORY 4. VOLUM 9. CHANNEL 5. 12 DIAL BUTTONS 10. BATTERY LOW INDICATOR 11. MICROPHONE Handset Telescopic Antenna Antenna LOW BATT The red LED blinks when the Battery Pack is low and Indicator needs to be recharged. TALK Button Press to place or answer a call. When finished, press this button to hang up. TALK Indicator The TALK LED lights when the phone is in use and blinks when you use memory funct
ملخص المحتوى في الصفحة رقم 11
FLASH Button When making a call, press to send a timed "hook-t1ash" on the telephone line for accessing services such as call waiting, etc. CHANNEL Use to select 1 of the 25 (NZ) or 10 (AUS) channels for Button the clearest operation. (Note: Operates only when the phone is in use). If interference is heard during a telephone conversation, simply press the channel button to select a new channel. MEMORY Use when storing numbers into the memory and when Button dialing a stored number. REDIAL Button
ملخص المحتوى في الصفحة رقم 12
Read This before Installation We have designed your telephone to conform to Australia or New Zealand Radio Frequency regulations, and you can connect it to most telephone lines. However, each device that you connect draws power from the phone line. We refer to the power drawn as the device's Ringer Equivalence Number or RN. The RN is shown on the bottom of your telephone. If you are using more than one phone or other device on the line, add up all the RN's. If the total is more than five, your p
ملخص المحتوى في الصفحة رقم 13
OVERVIEW IMPO R T ANT INFO RMA TI 0 N Operating range depends on a variety of factors, such as the weather, the . construction and layout of your home, etc. Aluminum siding, foil-backed insulation and iron roofing may limit operating range. Fluorescent lights and some appliance~such as microwave ovens and baby monitors are also liable to cause interference. Forclearestreception: . . Plug your XC630/633 base unit into AC power outlet that is not on the same circuit as one used by radio, hi-fi, te
ملخص المحتوى في الصفحة رقم 14
Installing Your Cordless Telephone Selecting the Installation Location Select a location for the XC630/633 to avoid excessive heat or humidity (as in a kitchen or bathroom). The Base Unit can be placed on a desk or tabletop near a standard 230/240Y AC outlet and standard telephone line socket, or mounted on a wall. Keep the Base Unit and Handset away from sources of electrical noise, (motors, fluorescent lighting). Be sure there is sufficient space to safely extend the Base Unit antenna fully. C
ملخص المحتوى في الصفحة رقم 15
Installing the Telephone on a Desk or Tabletop ~~. ~ 9VDC INPUT JACK TEL LlNE~ 1. Place the Base Unit on a desk or tabletop, and plug one end of the Telephone Line Cord (supplied) into the "TEL LINE" jack on the Base. 2. Plug the other end of the Telephone Line Cord into the telephone socket. 3. Plug the AC Adaptor cord into the 9Y DC input jack on the Base Unit. (Note: Use only the AC Adaptor supplied with the XC630/633.) 4. Plug the AC Adaptor into a standard 230/240Y AC wall outlet. (Note: Th
ملخص المحتوى في الصفحة رقم 16
Mounting the Telephone on a Wall The XC630/633 can be mounted directly on a wall. D---- To TEL LINE Jack To DC IN 9V~ Input Jack 1. Carefully select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. 2. Locate a suitable wall surface to a power outlet and a telephone socket. Install the 2 screws provided at a distance of 3.5 cm apart. Do not screw in completely, leaving 5mm protruding from the
ملخص المحتوى في الصفحة رقم 17
Installing the Battery Pack Black Wire to top v ~ 1. Remove the battery compartment cover on the back of the Handset by sliding it up. 2. Connect the Nickel-Metal Hydride Battery Pack by plugging it into the socket inside the battery compartment. (Note: The connector fits only one way and requires only a minimal amount of pressure to insert. Always install the Battery Cable with the Black wire to the top) 3. Place the Battery Pack inside the compartment and slide the battery cover back. Make sur
ملخص المحتوى في الصفحة رقم 18
Low Battery Indicator When the Battery Pack voltage level in the Handset is very low and needs to be charged, the BAIT LOW LED blinks. If this occurs while you are on the phone, a short alert beep will also be heard. When this happens, complete your call as early as possible, and return the Handset to the Base Unit for charging. Allow 12to 16hours without any interruption for the handset to fully recharge. Cleaning the Battery Contacts To maintain a good charge condition, it is important to clea
ملخص المحتوى في الصفحة رقم 19
Using Your XC 630/633 Selecting Pulse or Tone Dialing (Available on Australian Models only) Australian models can use either Pulse Dialing or Tone Dialing, depending on the local service. New Zealand models are Tone Dialing only. To set the Tone or Pulse Dialing, place the TONE/PULSE switch on the Base Unit in the proper position. The tone pulse switch is situated underneath the bottom of the base unit. This switch has been disabled for the New Zealand models. Placing a call To place a call with
ملخص المحتوى في الصفحة رقم 20
If the noise persists, or a double beep is heard, move closer to the base before pressing CHANNEL. If the noise ~ or interference continues, refer to the section entitled NOTE "Trouble shooting" in this manual. If you have more than one cordless phone in your house, ~ they must be set to different channels. NOTE Using the Flash Button Use FLASH to send a timed "hook-flash" on the telephone line for accessing services such as call waiting, etc. To use this function, simply press the FLASH button
