Panasonic CT-32SX31CE دليل المستخدم

دليل المستخدم للجهاز Panasonic CT-32SX31CE

جهاز: Panasonic CT-32SX31CE
فئة: تلفزيون CRT
الصانع: Panasonic
مقاس: 4.5 MB
مضاف: 1/18/2014
عدد الصفحات: 31
اطبع الدليل

تحميل

كيفية استخدام هذا الموقع؟

هدفنا هو أن نوفر لك وصولاً سريعًا إلى محتوى دليل المستخدم الخاص بـ Panasonic CT-32SX31CE. باستخدام المعاينة عبر الإنترنت ، يمكنك عرض المحتويات بسرعة والانتقال إلى الصفحة حيث ستجد الحل لمشكلتك مع Panasonic CT-32SX31CE.

لراحتك

إذا لم يكن البحث في دليل المستخدم Panasonic CT-32SX31CE مباشرة على موقع الويب هذا مناسبًا لك ، فهناك حلان محتملان:

  • عرض ملء الشاشة - لعرض دليل المستخدم بسهولة (بدون تنزيله على جهاز الكمبيوتر الخاص بك) ، يمكنك استخدام وضع العرض بملء الشاشة. لبدء مشاهدة دليل المستخدم Panasonic CT-32SX31CE بملء الشاشة ، استخدم الزر تكبير الشاشة.
  • التنزيل على جهاز الكمبيوتر الخاص بك - يمكنك أيضًا تنزيل دليل المستخدم Panasonic CT-32SX31CE على جهاز الكمبيوتر لديك والاحتفاظ به في ملفاتك. ومع ذلك ، إذا كنت لا تريد أن تشغل مساحة كبيرة على القرص الخاص بك ، فيمكنك دائمًا تنزيله في المستقبل من ManualsBase.
Panasonic CT-32SX31CE دليل الاستخدام - Online PDF
Advertisement
« Page 1 of 31 »
Advertisement
النسخة المطبوعة

يفضل العديد من الأشخاص قراءة المستندات ليس على الشاشة ، ولكن في النسخة المطبوعة. تم أيضًا توفير خيار طباعة الدليل ، ويمكنك استخدامه بالنقر فوق الارتباط أعلاه - اطبع الدليل. لا يتعين عليك طباعة الدليل بالكامل Panasonic CT-32SX31CE ولكن الصفحات المحددة فقط. ورق.

الملخصات

ستجد أدناه معاينات لمحتوى أدلة المستخدم المقدمة في الصفحات التالية لـ Panasonic CT-32SX31CE. إذا كنت ترغب في عرض محتوى الصفحات الموجودة في الصفحات التالية من الدليل بسرعة ، فيمكنك استخدامها.

ملخصات المحتويات
ملخص المحتوى في الصفحة رقم 1

ORDER NO. MTNC010524C1
B5
Service Manual
Color Television
Main Manual
(NA8ML)
Panasonic
Models
Chassis
CT-32SX31E BP371
CT-32SX31UE BP371
CT-32SX31CE BP371
CT-36SX31E BP372
CT-36SX31UE BP372
CT-36SX31CE BP372
This Service manual is issued as a service guide for the models of the NA8ML family listed above. Included in this
manual are a set of schematic, block diagrams, functional descriptions, alignment procedures, disassembly
procedures and a complete parts list.
“WARNING! This Service Manual is

ملخص المحتوى في الصفحة رقم 2

Important Safety Notice Special components are used in this television set which are important for safety. These parts are identified on the schematic diagram by the symbol and printed in BOLD TYPE on the replacement part list. It is essential that these critical parts are replaced with the manufacturer’s specified replacement part to prevent X-ray radiation, shock, fire or other hazards. Do not modify the original design without the manufacturer’s permission. Safety Precautions General Guideli

ملخص المحتوى في الصفحة رقم 3

Important Safety Notice . . . . . . . . . . . . . . . . . . 2 Instructional Flow Chart for Serviceman Mode . . . . . . . . . . . . . . . . . . . 24 Safety Precautions . . . . . . . . . . . . . . . . . 2 Service Adjustments General Guidelines. . . . . . . . . . . . . . . . . 2 (Electronic Controls). . . . . . . . . . . . . . . . . 27 Leakage Current Cold Check . . . . . . . . . 2 X-ray Radiation. . . . . . . . . . . . . . . . . . . . 2 Sub-Contrast Adjustment . . . . . . . . . . . 27 Horizontal O

ملخص المحتوى في الصفحة رقم 4

Service Notes Note: These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose. Leadless Chip Component How to Replace Flat-IC - Required Tools - (surface mount) Chip components must be replaced with identical chips • Soldering iron • De-solder braids due to critical foil track spacing. There are n

ملخص المحتوى في الصفحة رقم 5

Service Notes (Continued) IMPORTANT: To protect against possible damage to Preparation the solid state devices due to arcing or static 1. Connect Receiver to AC 120 Volts. Do not turn ON. discharge, make certain that all ground wires and CTR 2. Connect HIGH VOLTAGE meter to 2nd anode DAG wire are securely connected. (H.V. button). Note: Use cold ground( ) for negative lead. CAUTION: The power supply circuit is above earth 3. Connect the ammeter serial from the flyback anode ground and the chassi

ملخص المحتوى في الصفحة رقم 6

Receiver Feature Table FEATURE\MODEL CT-32SX31E/UE/CE CT-36SX31E/UE/CE Chassis NA8ML Tunning system 96K # of channels 181 Menu language Eng/Span/Fr Closed Caption X V-Chip (USA/CANADA) X 2RF X Remote Model # EUR511500 Picture tube AMEC Comb Filter 3 DIG VM X V/A norm X Color Temp X MTS/SAP/DBX X BASS/BL/TRE Control X AI Sound X Surround X SPATIALIZER/BBE BBE Built-in audio power 10W/CH (10%) # of speakers 2 A/V in (rear/front) 3(2/1) S-VHS Input (rear/front) 1/1 Component Input 1 (Y,Pb,Pr) Audio

ملخص المحتوى في الصفحة رقم 7

Location of Controls (Receiver) Front A/V Jacks VOLUME CHANNEL ACTIO TV N /VIDEO POWER Controls Inside Remote Control Sensor front door 2 3 4 5 1 Figure 3. Location of Controls (Receiver). Quick Reference Control Operation Quick Reference Control Operation 1 Power Button - Press to turn ON or OFF. Volume Buttons - Press to adjust Sound Level, or to adjust Audio Menus, Video 2 Menus, and select operating features when menus are displayed Channel Buttons - Press to select programmed chann

ملخص المحتوى في الصفحة رقم 8

Location of Controls (Remote) MULTI Button POWER Button Programmable button that can Press to turn ON and OFF. operate up to seven (7) functions at MUTE Button once Press to mute sound. TV/VIDEO Button A second press resumes sound. Press to select TV or Video input. Press also to access and delete Closed Caption display. CH (channel) Buttons VCR, DVD, LD/CD, AUX, TV, CBL, Press to select channels. DBS, RCVR Use with volume buttons to navigate in menus. Component function buttons DBS EXIT, DBS

ملخص المحتوى في الصفحة رقم 9

Disassembly for Service To release screen GND cables from L-Board L11 & L12 Back Cover connectors, insert a wire in both sides of connector and Remove all the screws marked with an arrow( ) pull upwards the cable, then remove the wire from the back of the Receiver. (See Fig. 6) Note: Screw configuration, type, and number Insert wire of screws vary depending on the Pull cable upwards model of the Receiver serviced and the application; various models are covered in this Manual. Use same hardwa

ملخص المحتوى في الصفحة رقم 10

Disassembly for Service (Continued) Note: To remove the four brackets holding the degauss coil from the corners of Note: Reuse all the clampers and mounting the CRT, first remove the CRT from brackets from the degaussing coil and the cabinet, then remove the Brackets screen, and when remounting the by pressing the tab on the bracket and degaussing coil assure that is not pull upwards. These Brackets are touching the speakers, this can be included in the Degauss Coil Kit, for done by placing some

ملخص المحتوى في الصفحة رقم 11

Back Cover Removal 4 screws at top edge 1 screw by antenna jacks 1 screw 1 screw 1 screw at lower 1 screw 1 screw at lower right corner left corner 1 screw Figure 8. Back Cover Removal - 11 -

ملخص المحتوى في الصفحة رقم 12

D751 + Chassis Service Adjustment Procedures All service adjustments are factory preset and should not require adjustment unless controls and/or associated components are replaced. Note: Connect the (-) lead of the voltmeter to the appropriate ground. Use heat sink when the HOT ground symbol ( ) is used. Otherwise, use COLD ground ( ) — Tuner shield. L826 Q804 A-BOARD D-BOARD Q002 L824 + - IC001 IC881 IC882 IC883 C840 IC002 L008 T801 IC101 Q801 IC2301 IC1801 T T U U N C3023 IC3001 N E - E R Q55

ملخص المحتوى في الصفحة رقم 13

Purity and Convergence Procedure Adjustment is necessary only if the CRT or the Vertical Raster Shift Adjustment (Only for deflection yoke is replaced or if the setting was Models with Purity/Convergence Assembly with 4 disturbed. The complete procedure consists of: Pairs of Rings). 1. Vertical Raster Shift Adjustment. (Only for Models Apply a green pattern with a horizontal line, adjust the with Purity/Convergence Assembly with 4 Pairs Deflection Yoke so that has no tilt, then secure it. of R

ملخص المحتوى في الصفحة رقم 14

Initial Center Static Convergence Final Convergence Procedure (see Fig.17 Connect a dot/cross hatch generator to the Receiver through Fig. 19): and tune in a signal. Observe misconvergence at Note: Vertical size and focus adjustments must be center of the screen only. completed prior to performing the convergence Adjust the R&B pole magnets; by separating tabs and adjustment. Connect a dot pattern generator to the rotating to converge blue with red. Receiver. The Brightness level should not be h

ملخص المحتوى في الصفحة رقم 15

YH Adjustment (VR2 for Vertical dynamic Permalloy Convergence Corrector Strip convergence) (Part No. 0FMK014ZZ) 1. Apply a crosshatch pattern. 2. Adjust contrast and brightness customer controls This strip is used in some sets to match the yoke and CRT for optimum convergence. If the yoke or CRT is to obtain a correct picture. replaced, the strip may not be required. 3. With a driver Adjust VR2 (located in deflection yoke First converge the set without the strip and observe board Fig. 19) to o

ملخص المحتوى في الصفحة رقم 16

As the yoke is tilted G vertically, the rasters R B produced by the outside guns rotate in opposite directions. Figure 17. Vertical Yoke Movement Raster produced from one of the outside electron beams Raster from the other side electron beam RG B Static convergence magnets are set for center convergence As the yoke is tilted horizontally, one raster gets larger while the other gets smaller Figure 18. Horizontal Yoke Movement For Adjustment 2 Poles(Purity) 2 Poles(VRS Adj) of DY (YHC/YV/XV) Dyn

ملخص المحتوى في الصفحة رقم 17

Serviceman Mode (Electronic Controls) This Receiver has electronic technology using the I²C Bus Concept. It performs as a control function and it replaces many mechanical controls. Instead of adjusting mechanical controls individually, many of the control functions are now performed by using “On Screen Display Menu”. (The Serviceman Adjustment Mode.) Note: It is suggested that the technician reads all the way through and understand the following procedure for Entering/Exiting the Serviceman Adju

ملخص المحتوى في الصفحة رقم 18

Press the Power Button on the Remote Control to select the Serviceman Adjustment . For Adjustments: 1.Press Channel Up/Down on the Note: Write Down the original 2.Press Volume Up/Down on the Remote Control to select one of value set (b in Fig. 20) for Remote Control to adjust the the available Service Adjustments each address before level of the selected Service (a in Fig. 20). modifying anything. It is Adjustment (b in Fig. 20). easy to erroneously adjust the wrong item. Default Sub-Data Adjus

ملخص المحتوى في الصفحة رقم 19

Press the Power Button on the Remote Control to select the Serviceman Adjustment For Adjustments: 1.Press Channel Up/Down on the Note: Write Down the original 2.Press Volume Up/Down on the Remote Control to select one of value set (b in Fig. 20) for Remote Control to adjust the the available Service Adjustments each address before level of the selected Service (a in Fig. 20). modifying anything. It is Adjustment (b in Fig. 20). easy to erroneously adjust the wrong item. Default Geometry Adjust

ملخص المحتوى في الصفحة رقم 20

Press the Power Button on the Remote Control to select the Serviceman Adjustment For Adjustments: 1.Press Channel Up/Down on the Note: Write Down the original 2.Press Volume Up/Down on the Remote Control to select one of value set (b in Fig. 20) for Remote Control to adjust the the available Service Adjustments each address before level of the selected Service (a in Fig. 20). modifying anything. It is Adjustment (b in Fig. 20). easy to erroneously adjust the wrong item. Default PIP Adjustment


أدلة المستخدم البديلة
# دليل الاستخدام فئة تحميل
1 Panasonic BT-LH1700WP دليل الاستخدام تلفزيون CRT 5
2 Panasonic CT 13R28W دليل الاستخدام تلفزيون CRT 4
3 Panasonic Color Television CT-27G24 دليل الاستخدام تلفزيون CRT 8
4 Panasonic CT 13R17B دليل الاستخدام تلفزيون CRT 8
5 Panasonic CT 20G7D دليل الاستخدام تلفزيون CRT 2
6 Panasonic CT 13R18B دليل الاستخدام تلفزيون CRT 0
7 Panasonic CT 20SL13 دليل الاستخدام تلفزيون CRT 4
8 Panasonic CT 13R38S دليل الاستخدام تلفزيون CRT 4
9 Panasonic CT 20SL15 دليل الاستخدام تلفزيون CRT 10
10 Panasonic CT 20SX11 دليل الاستخدام تلفزيون CRT 1
11 Panasonic CT 20D12D دليل الاستخدام تلفزيون CRT 1
12 Panasonic BT-YAE1700G دليل الاستخدام تلفزيون CRT 6
13 Panasonic CT 20SX10 دليل الاستخدام تلفزيون CRT 2
14 Panasonic CT 24SX11 دليل الاستخدام تلفزيون CRT 1
15 Panasonic CT 25G7 دليل الاستخدام تلفزيون CRT 2
16 Sony BRAVIA 32EX308 دليل الاستخدام تلفزيون CRT 10
17 Sony E42A10 دليل الاستخدام تلفزيون CRT 3
18 Sony FD Trinitron KV-21FX20K دليل الاستخدام تلفزيون CRT 58
19 Sony BRAVIA KDL-26T30 دليل الاستخدام تلفزيون CRT 7
20 Sony BRAVIA 46HX701 دليل الاستخدام تلفزيون CRT 4