Amana L0503010 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

BUILT- N DISHWAS
iNSTALLATION iNSTRUCT!ONS
LEAVEINSTALLATION INSTRUCTIONS AND
USER'S GUIDEWITH OWNER
ALLELECTRIC WIRINGAND PLUMBINGMUST BEDONE
IN ACCORDANCE WITH NATIONALAND LOCALCODES.
PRINTED]INUSA © 1999 - Maytag Corporation 6 915126 B

ملخص المحتوى في الصفحة رقم 2

TOOLSRECKSSAR¥FOR |NSTAL T|ON* SUPPORTACCESSORIES: (2)RATCHET 0 3/4" ULApproved Strain Rdief (proqded) O 2 Appropriate Sized Wire Nuts O 3/16", 1/4", 5/16" SOCKETS O 3/8" Male (NZT.) Compression Elbow O PHILLIPS SCREWDRIVER or Flare Elbow O STANDARD SCREWDRIVER O Thread Sealing Tape or Pipe Thread Compound © WIRE CUTTERS O Appropriate Sized Hose qamp © CRESCENTWRENCH O 2 Wood Mounting Screws (provided) © ADJUSTABLEPLIERS Water Hook-Up Kits Available: © LEVEL (l_atel line wattl vane fitting Teflo

ملخص المحتوى في الصفحة رقم 3

WATER VALV O Remove shipping plug from water hflet valve, O Install a 90° elbow (3/8" N,P.T) fitting h,to the water valve using Teflon r'_ tape or pipe thread compound. The opposite end of"the fitth*g should fit h_-eoming hot water supply line. Position the end of the elbow towards the rear of the dishwasher IMPORTANT: DO NOT connect a sweat type fitting directly to the water valve as the required beat will damage the water inlet valve. Do not solder within 6" (15.2 era) from the water valve. C

ملخص المحتوى في الصفحة رقم 4

|OR|NG THEDISHWASHER(conUnued) and horizontally. A combination of these two adjustments are necessary to properly position the dishwasher and insure proper fit of door m_d latch. Dishwasher must be LEVEL, solid, m_d square. SECURING TRE Make pilot holes in the underside of counter and drive wood screws, provided in the accessory paekag< through holes in the dishwasher mounting bracket. If part of the bracket extends beyond the cabinet front, they may be trimmed with wire cutters, provided suffi

ملخص المحتوى في الصفحة رقم 5

THE F_CTREAL CONNECF|ONS SEE THE ELECTRICAL REQUIREMENTS SECTION CAUTION: Verify power to dishwasher is off at source. n ....... 27- ZZ O Remove terminal box covet: Ix order to secure the power supply cable, a UL listed strain relief nmst be used to secure .2-_--_ ol the power supply to the back of tet'mina[ box, Q Strip approximatdy 3/8" (.09 em) of"insulation fl'om incoming power supply wires. Connect O Terminal I_o_ these wires to wires from dishwasher wire ]harness located in the terminal bo

ملخص المحتوى في الصفحة رقم 6

CAUTION: Disconnect dectricN power before you start! This dishwasher is designed for ALL ELECTRICALWIRING AND GROUNDING operation on an adequately SHOULD BE DONE IN ACCORDANCE WITH wired individual 120 VAC, NATIONAL AND LOCAL CODES. 60 Hz approved electrical circuit. Use required fl_se (15 amp) or comparable circ1_it breaker. Two wire with grolmd service to the dishwasher is recommended for connection at the terminal box and for gro@ding. GROUNDING INSTRUCTIONS This appliance must be connected t