ملخص المحتوى في الصفحة رقم 1
WC140 Integrated Dishwasher
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
ملخص المحتوى في الصفحة رقم 2
Important Important The CDA Group Ltd cannot be held r The CDA Group Ltd cannot be held r esponsible for injuries or losses caused by inc esponsible for injuries or losses caused by inc orrect use or installation of this orrect use or installation of this product. Please note that CD product. Please not A reserve the right t e that CDo in A reserv validat e the right t e the guaro in antee supplied with this pr validate the guarantee supplied with this pr oduct following incorr oduct f ect ollo
ملخص المحتوى في الصفحة رقم 3
R Rec ecomendations ommendations • • T To r o reduc educe ener e energy and w gy and wat ater c er consumption, r onsumption, r emov emov e all dirt r e all dirt r esidues fr esidues fr om the dishes prior t om the dishes prior t o loading the dish o loading the dish w• washer. • Only run the dishwasher only when fully loaded. • Only run the dishwasher when fully loaded. • Place hollow items (bowls, glasses and pans) face down in the basket. • Place hollow items (bowls, glasses and pans) face
ملخص المحتوى في الصفحة رقم 4
Starting a programme • Pr ess the P ow er but t on. • Press the Programme Selection button until the required programme light is illuminated. • If required, press the Delay Timer button. • Onc e the pow er is s wit c hed on, the end of Pr ogr amme Indicat or light will switc h on. • Onc e a pr ogr amme is select ed, the end of Pr ogr amme Indicat or light will switc h off, and the Pr ogr amme Indicat or light will switch on. • When you close the dish w asher door the pr ogr amme will
ملخص المحتوى في الصفحة رقم 5
Detergent To fill the detergent compartment 1. Push the latch as shown in figure 1. 2. Add the required amount of detergent. The main detergent compartment “b” (figure 2) has lines to allow for specific amounts of 3 3 detergent. These are marked at either 15 cm or 25 cm , to be used depending on how dirty the dishes are. 3 If your dishes are in need of an intensive wash, then add 5 cm of detergent into the prewash section of the compartment “a” (figure 2). 3. Then close the d
ملخص المحتوى في الصفحة رقم 6
ENGLISH T esting strip The washing effectiveness of your machine depends on the softness of the tap water. For this reason, your machine is equipped with a system that reduces the hardness in mains water supply.The washing effectiveness will increase when the system is correctly set. To find out the water hardness level of water in your area, contact your local water board or determine water hardness level by using the test strip(if available). Open the Run Keep the Shake the Wait for Make your
ملخص المحتوى في الصفحة رقم 7
Rinse Aid Rinse Aid To fill the rinse aid c Rinse Aid ompartment Rinse Aid To fill the rinse aid compartment To fill the rinse aid compartment To fill the rinse aid compartment 1. Open the rinse aid compartment by turning and removing the cap as 1. Open the rinse aid compartment by turning and removing the cap as 1. Open the rinse aid compartment by turning and removing the cap as shown in figure 4. 1. Open the rinse aid compartment by turning and removing the cap as shown in figure 4
ملخص المحتوى في الصفحة رقم 8
Dishwasher Baskets To adjust the height of the upper basket: 1. Open the basket retaining clips, as shown in figure 7, but turning them to the side. 2. Remove the upper basket, and relocate the alternate set of wheels on the runner, as shown in figure 8, pushing the basket back into place. 3. Close the basket retaining clips. fig 7 The images below are designed as guidance as to best practice for loading the dishwasher. Upper basket fig 8 Lower basket Bad loads
ملخص المحتوى في الصفحة رقم 9
Standard loading and Test Data Capacity • Upper and lower baskets: 12 place settings. • The upper basket should be adjusted to high position. • Cups should be placed on to the dish rack pins. Detergent / Rinse aid 3 • 5 + 25 cm , in accordance with EN50242-DIN 44990 IEC 436 (international norms) / Rinse aid dosage adjustment: 4. Programme test • Economic 50°C, in accordance with EN 50242 (international norms.).
ملخص المحتوى في الصفحة رقم 10
Programme Listing Programme Intensive Normal Economic Quick Prewash names and 65°C (P1) 55°C (P2) 50°C (P3) 40°c (P4) No Heat (P5) temperatures Pre-wash to soups, sauces, soups, sauces, coffee, milk, coffee, milk, rinse and loosen Type of pasta, eggs, pilaf, pasta, eggs, pilaf, tea, cold meats, tea, cold meats, residue-awaiting full food waste potato and oven potato and oven vegetables, not vegetables, not load-then select a dishes, fried foods dishes, fried foods kept for long kept for
ملخص المحتوى في الصفحة رقم 11
ENGLISH MAINTENANCE AND CLEANING Cleaning the machine in regular intervals prolongs the machine's service life. Oil and lime may accumulate in the machine's washing section. In case of such accumulation; ENGLISH -Fill the detergent compartment without loading any dishes into the machine, select a programme that runs at high temperature, and start the machine. In case of insufficiency, use special cleansing material available in the market. (Cleansing material produced special to ENGLISH machines
ملخص المحتوى في الصفحة رقم 12
Failure Codes and Troubleshooting Your dishwasher control panel is equipped with a diagnostic display to help in the event of a problem with the appliance. Error Code Error description Advice Intensive Normal Eco Quick Prewash Make sure the water inlet tap is fully open Close the water tap, separate the Inadequate water water inlet hose from the tap and supply clean the filter Restart your machine, contact CDA service if the error resumes Close the tap and contact Continual fill error CDA s
ملخص المحتوى في الصفحة رقم 13
Failure Code and Troubleshooting Problem Possible cause Check the plug, fuse and circuit breakers of the mains supply The water tap is turned off The programme will not start The dishwasher door is not fully closed The water inlet filter or the machine filters are blocked The water drain hose is blocked or kinked. The water drain hose is blocked or knicked Water remains inside the dishwasher at the end of the The filters are blocked programme Power failure The dishwasher stops in the middle of
ملخص المحتوى في الصفحة رقم 14
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable f
ملخص المحتوى في الصفحة رقم 15
Installation • Do not install this appliance if it is damaged in any way. Installing a damaged appliance may invalidate the warranty. • The water supply tap should be located in an adjacent cupboard so that it can be accessed after installation. • Ensure the appliance is level by adjusting the feet as necessary. • Only use the water inlet supplied with the appliance. • If the water pressure is above 10 bar, a pressure relief valve should be used. • After connecting the water s
ملخص المحتوى في الصفحة رقم 16
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
ملخص المحتوى في الصفحة رقم 17
CDA Dishwasher – Oversized Fascia Door Mounting Information Scope of Document: Where non-standard integrated appliance doors are supplied, additional fitting instructions are required to ensure compatibility with this product. Instructions: The machine is supplied with a fitting template and these instructions should be followed as normal. However, the fitting template needs to be located lower down the fascia door; this is shown below: - Offset Y Door Height
ملخص المحتوى في الصفحة رقم 18
