ملخص المحتوى في الصفحة رقم 1
5 & 7.5 HP
Direct Drive Cyclonic
Dust Collectors
Owner’s Manual
Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204
Phone 1-800-732-4065 315-476-5151 Fax 315-476-5044 www.oneida-air.com
ملخص المحتوى في الصفحة رقم 2
Thank You for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only. Our qualified technicians and sales staff are available 7:30am - 6:00pm EST Mon. - Thur. and 7:30am - 5:00pm EST Fri. to answer any questions concerning OAS products and dust collection. Call for ductwork design and ductwork quotes, including system pricing and shipping cost. Read the entire Owner’s Manual before installing or operating system! Proudly Made in the U.S.A. Table of Cont
ملخص المحتوى في الصفحة رقم 3
I. System Start-Up Information 1. Read the installation and maintenance instructions as well as the recommended safety practices in this manual. 2. Install Ductwork completely: A.) Seal ductwork with silicone sealant or duct tape. B.) Have Dust Bin in place and sealed before running Dust Collector. 3. Wire Fan / Blower according to wire diagram on pg. 11 in this owner’s manual. 4. Have a licensed electrician check current draw on motor with all gates open. Current draw should not exceed max
ملخص المحتوى في الصفحة رقم 4
II. 5 & 7.5hp Direct Drive Configurations 1. No Filter - Vent Outside - 1. No Filter Caution: If exhaust air is vented outside you must provide make up / return air. Flue gases (carbon monoxide) can be drawn into the shop from furnaces, water heaters or other appliances. Plenum Assembly Pleated 2. External Cartridge Cartridge Filters Filters Plenum Assembly Removable Dust Containers Removable Chip / Dust Bin Tube Filters 3. External Tube Filter 5 Gal. Buckets - Collects fine dus
ملخص المحتوى في الصفحة رقم 5
III. General Specifications & Fan Performance Curves Physical and Electrical Data for 5 and 7.5hp Direct Drive Systems. System Performance Dust Bin 5hp 1220 max cfm - 2250 cfm w/ typical ductwork 55 Gal. Steel Drums 7.5hp 2900 max cfm - 2500 cfm w/ typical ductwork Large dust bins available System Dimensions Options Height w/ 55 Gal. Drum: 132” Angle iron stand for free-standing unit Footprint: 8.5’ x 3’ Silencers available Fan Wheel diameter: 16” Air Foil design Magnetic Motor Starters Cyclone
ملخص المحتوى في الصفحة رقم 6
IV. Dimensions 1.5” 14 1/2” 7 3/4” Top View 32 1/8” 30” O.D. of Bolt Mounting Holes Ring 30 3/8” 62” 105” 39 1/4” 122.125” w/ 55 gal. steel drum 73 1/8” 102” 131” w/ 55 gal. steel drum 69.875” 43” Note: Overall height dimensions are w/ 55 gal. drum. 24 1/4” 1.5” 36” 12” 1.25” Flange 116 1/8” 122 1/8” - with 8’ Bags 7.64” I.D. 10.031” I.D. 12” Tube Filters - Height for 8’ bags. Other heights available. 5 c 5 - 7.5 HP Direct Drive Owner’s Manual O.A.S. 2002
ملخص المحتوى في الصفحة رقم 7
V. Angle Iron Stand Cross Brace for Cyclone Angle Ring to sit on 1. Choose the system orientation, plenum can be on the right or the left of the cyclone. Bolt together the stand using the cross bars and 3/8” x 1” bolts. Note: the cross bar on the cyclone stand goes in the back so that the dust bin can slide out. 6 c 5 - 7.5 HP Direct Drive Owner’s Manual O.A.S. 2002
ملخص المحتوى في الصفحة رقم 8
1. VI. Assembly Instructions Fan / Blower Fan / Blower is shipped strapped to Cyclone Barrel. It is NOT attached to the unit. You must bolt them together. Follow the instructions below. Air 1. Orient the blower housing to match the stand Air Inlet Outlet configuration and the desired angle for the cyclone inlet. Bolt the fan / blower to the cyclone barrel using the Silicone hardware taped on the motor. Bead Bolts are already welded on Fan/Blower unit. Put a bead of silicone around top hole in c
ملخص المحتوى في الصفحة رقم 9
VI. Assembly Instructions (Cont.) 4. 5. Attach flex hose to bottom of collector and to lid of dust bin. Securely fasten hose clamps. There must be Collector an air tight seal between the collector and dust bin. 6. Make sure the dust bin lid sits securely and the rubber Hose Clamp gasket on the bin lid is in place on the barrel. Maintain an air tight seal between cyclone and dust bin to prevent Flex Hose motor from overloading. Hose Clamp IMPORTANT: Do not operate the collector until the dust b
ملخص المحتوى في الصفحة رقم 10
VIII. External Filter Bag Assembly Plenum Box 22 gauge galv. OAS Galvanized Plenum Box 1. Connect the plenum to the fan / blower outlet with the bolts provided. Band clamp tube filters to the Ring Thimbles on the bottom of the plenum and to the tops of the 5 gal. buckets. (Check mounting height - Match to bag heights) Build your own plenum Ring Thimble Plenum box can be constructed of plywood or metal. Part # - FAZ000000 Oneida Air Systems sells 22 gauge galv. plenum boxes. The filter medium i
ملخص المحتوى في الصفحة رقم 11
IX. Filter Maintenance External Filter Cartridge Cleaning Intervals Do not remove fabric When unit is turned off, use compressed air to blow dust off from straps around exterior of filter. Hold nozzle at least 8” away from filter pleats*. pleated Do not remove bottom dust pan before or during the blow-off cartridge. process! Let dust settle into dust pan. Unclip and dump out dust. Filter removal is not required. You can also run your fingers around the filter pleats to knock material down. * WAR
ملخص المحتوى في الصفحة رقم 12
IX. Single and Three Phase Wire Diagram Use wiring diagram on motor plate if different from below. Wiring should always be done by a licensed electrician! - Electrically insulate all connections. - For counter-clockwise rotation, looking from top of motor down. 5hp Single Phase Leeson Motor / 230v / 19.8 amps / TEFC / C Face / 3500 rpm P1 Power Line 1* Top View T1 Tie together and insulate with a wire nut (do NOT connect to Outlet T8 any house wiring) T4 Power Line 2* T5 * Power Line 1 and 2 ar
ملخص المحتوى في الصفحة رقم 13
X. Accessories Bindicator - Provides level sensing for dry bulk solids. The Bindicator operates by using a 1 rpm synchronous motor to rotate a paddle. When paddle rotation is impeded by material surrounding it, the motor is de-energized and triggers a SPDT snap switch. The snap switch can be used in conjunction with a motor starter to turn equipment off or provide alarm functions. Magnetic Motor Starters - The 5 and 7.5hp direct drive dust collectors do not come wired or with an on/off switch
ملخص المحتوى في الصفحة رقم 14
XII. Troubleshooting Motor Overheating The motor’s internal circuit breaker will trip if the motor is overheating. Caused By: Air leaks between the collector and dust bin - The lid of the dust bin and the cyclone must be in place and sealed when operating the dust collector. - Make sure flex hose is not torn and the hose clamps are tight. - Check drum lid; cover should have a foam seal and be well seated. - Check for holes or leaks in the dust bin barrel. Motor not
ملخص المحتوى في الصفحة رقم 15
Read Before Installing and Operating XIII. Fire Hazards - Oneida Collectors are designed for WOOD DUST only!! Wood shaping and cutting processes generate wood chips, shavings, and dust. These materials are considered combustible. Air borne wood dust below 420 microns in size (.017 of an inch) in certain concentration ranges when ignited can deflagrate (burn quickly). An ignition source such as a spark, or ember, can ignite a dust mixture resulting in an expanding flame front, which can cau
ملخص المحتوى في الصفحة رقم 16
XIII. Terms and Conditions Checking in Order Please look over the shipped order very carefully in the presence of the delivery person for damage or incomplete shipment before signing the delivery receipt. Please note any tears or irregularities in shipping packaging, however slight, on the shipping delivery receipt. This could be an indication of extensive concealed damage. The shipping company will not take responsibility if the damage is not noted on the delivery receipt. In the event of sh
