ملخص المحتوى في الصفحة رقم 1
www.collegehillshonda.com
Accessory Application Publications No.
AII 38137-38714
INSTALLATION
Accessory HandsFreeLink 2008 ODYSSEY
Issue Date
INSTRUCTIONS
JAN 2008
PARTS LIST Fuse label
HFL Attachment Kit
P/N 08E02-SHJ-100B
HFL trim
Fuse (2 A)
6 EPT sealers
HFL bracket
HFL harness
8 Wire ties
HFL subharness
4 Self-tapping screw, 3 x 10 mm
2 Washer screws, 4 x 12 mm
2 Double-faced tapes
Self-tapping screw
HFL retainer
Bush
Ground bolt
Template
Rubber bumper
© 2008 American Honda Motor Co., Inc. -
ملخص المحتوى في الصفحة رقم 2
www.collegehillshonda.com HFL Blue Tooth Kit Illustration of the HFL Installed on the Vehicle P/N 08E00-E10-100 CONTOROL Switch SWITCH UNIT HFL HARNESS Control unit FUSE (2 A) Accessory User's Information Manual HFL SUBHARNESS 7518071E INSTALLATION Customer Information: The information in this TOOL AND SUPPLIES REQUIRED installation instruction is intended for use only by #2 Phillips screwdriver skilled technicians who have the proper tools, 10 mm Combination wrench equipment, and training to co
ملخص المحتوى في الصفحة رقم 3
www.collegehillshonda.com 3. Disengage eight retaining tabs and remove left 7. Using a flat-tip screwdriver, push the hook and and right lens from the roof console. turn the holder. Remove the holder. PLASTIC TRIM TOOL VEHICLE CONNECTORS SUNVISOR HOLDER VEHICLE ROOF SUNGLASS CONNECTOR CONSOLE HOLDER (Open.) COVER RIGHT LEFT RETAINING LENS SUNVISOR TAB 2 SCREWS 4 RETAINING TABS 8. Disengage two screws and remove the left 2 BOLTS sunvisor. 2 BOLTS LEFT 9. Pull away the weatherstrip from the left f
ملخص المحتوى في الصفحة رقم 4
www.collegehillshonda.com 10. Remove the left front door sill trim (three clips). 12. Attach the fuse label (2 A) to the fuse case of the HFL subharness. 3 CLIPS LEFT FRONT DOOR SILL TRIM FUSE LABEL (2 A) HFL HFL SUBHARNESS SUBHARNESS FUSE CASE 7821100B 4301210B 13. Plug the HFL subharness 6-pin connector into the 11. Pull away the weatherstrip from the left kick panel. 6-pin opening in the fuse box. Remove the left kick panel (three clips). 3 CLIPS WEATHERSTRIP HFL SUBHARNESS LEFT KICK PANEL 6
ملخص المحتوى في الصفحة رقم 5
www.collegehillshonda.com NOTE: If another accessory is already plugged into the 16. Remove the vehicle bolt (discard) and install the 6-pin connector, remove the dummy connector ground bolt with HFL subharness ground terminal from the 6-pin connector taped to the HFL as shown. subharness. Plug the 6-pin connector from the other accessory harness into the 6-pin connector from the HFL subharness you just unplugged and plug the HFL subharness into the fuse box. FUSE BOX HFL SUBHARNESS GROUND 6-PIN
ملخص المحتوى في الصفحة رقم 6
www.collegehillshonda.com 20. Secure the HFL subharness to the vehicle 23. Cut the template into template A and template B. harness with a wire tie. VEHICLE PANEL EPT TEMPLATE A SEALER TEMPLATE WIRE TIE HFL SUBHARNESS TEMPLATE B 7517091E 24. Remove the damper (two tapping screws). VEHICLE HARNESS 7517061E SUNGLASSES 21. Using isopropyl alcohol on a shop towel, clean the HOLDER area where the EPT sealer will attach. Attach a EPT sealer to secure the HFL subharness to the ROOF vehicle panel. CONSO
ملخص المحتوى في الصفحة رقم 7
www.collegehillshonda.com 27. Remove the console light from the roof console 29. Attach masking tape to the roof console as (four retaining tabs). shown. ROOF MASKING ROOF CONSOLE TAPE CONSOLE 4 RETAINING TABS 7716020X 30. Attach template A with masking tape to the roof CONSOLE LIGHT console at the indicated position. 7523030E ROOF CONSOLE CENTER OF THE PUSHPIN ROOF CONSOLE 28. Enlarge the hole on the roof console with 9 mm drill bit. FELT-TIP PEN ROOF CONSOLE MARK MASKING TAPE 2 MARKS TEMPLATE
ملخص المحتوى في الصفحة رقم 8
www.collegehillshonda.com 34. Drill 4.5 mm holes at the two locations marked on 39. Drill a 3 mm hole at the four locations marked on the roof console in step 32. After drilling, remove the roof console in step 36. any burrs. 19 mm DRILL BIT HOLE SAW (4.5 mm) DRILL BIT ROOF (3 mm) CONSOLE ROOF CONSOLE 4 MARKS DRILL BIT (3 mm 6 mm 10 mm) 2 MARKS 7517120E DRILL 35. Attach template B with masking tape on the roof console at the indicated position. 7517141E PUSHPIN 40. Enlarge the two 3 mm holes d
ملخص المحتوى في الصفحة رقم 9
www.collegehillshonda.com 42. Using a utility knife, cut along the marking made 45. Connect the HFL harness 22-pin connector to the on the roof console in step 37. After cutting, control unit. CENTER remove any burrs. CONTROL UNIT ROOF UTILITY CONSOLE KNIFE Mark made in step 37. CONTROL Cut out. UNIT ROOF CONSOLE HFL HARNESS ROOF HFL HARNESS CONSOLE Remove the 22-PIN adhesive CONNECTOR backing. ROOF CONSOLE 7517171E Cut out. 7517152E 46. Using isopropyl alcohol on a shop towel, clean the 43. Rem
ملخص المحتوى في الصفحة رقم 10
www.collegehillshonda.com 48. Bend the switch terminal as shown. 51. Connect the HFL harness 20-pin connector to the switch. BACKSIDE OF THE SWITCH SWITCH SELF- TAPPING TERMINAL SCREW (Reuse.) (Bend.) SPEAKER SWITCH SWITCH TERMINAL HFL TRIM VEHICLE BUSHES (Reuse.) SWITCH BUSHES HFL HFL HARNESS RETAINER 20 -PIN SELF- TAPPING ROOF 7517192E CONNECTOR SCREW CONSOLE 52. Install the switch assembled in step 50 to the roof console with self-tapping screw, bushes, tapping screw removed in step 25 and ve
ملخص المحتوى في الصفحة رقم 11
www.collegehillshonda.com 55. Hold the roof console close to the roof console 58. Connect the vehicle connectors to the roof opening and connect the HFL harness 4-pin console. Reinstall the roof console with the four connector to the HFL subharness 4-pin connector. bolts from step 5. VEHICLE WIRE TIE GREEN CONNECTORS CONNECTOR VEHICLE BRACKET HFL SUBHARNESS 4-PIN Vehicle front ROOF CONNECTOR CONSOLE ROOF CONSOLE OPENING 7518042E HFL HARNESS 2 BOLTS 4-PIN CONNECTOR 2 BOLTS ROOF CONSOLE 59. Instal
ملخص المحتوى في الصفحة رقم 12
www.collegehillshonda.com 60. Attach the fuse label to the No. 33 slot on the fuse 61. Check that all wire harnesses are routed properly box cover. and that all connectors are plugged in. 62. Reinstall all removed parts. FUSE LABEL (OPITION FUSE 2 A) 63. Reconnect the negative cable to the battery. 64. Enter the customer’s radio anti-theft code, and reset the radio station presets. FUSE BOX 65. Reset the clock. COVER NOTE: When the battery is disconnected, the driver’s window AUTO function is di
