ملخص المحتوى في الصفحة رقم 1
SSA-0412
USER GUIDE
4 Channel MPEG-4
Digital Video Recorder
Ver. 2.1
About this user guide
Before installing and using this unit, please read this user guide carefully.
Be sure to keep it handy for later reference.
This document contains preliminary information and subject to change without notice.
ملخص المحتوى في الصفحة رقم 2
BEFORE INSTALLATION NOTE: WE DO NOT TAKE ANY RESPONSIBILITY OF DAMAGES RESULTED FROM THE NON- STANDARDIZED GOODS AND FAILURES TO FOLLOW THE MANUAL INSTRUCATIONS. PLEASE ASK FOR HELP TO YOUR LAST SELLER BEFORE DISASSEMBLEING THE SYSTEM FOR REPAIR AND ADD PARTICULAR FUNCTIONS. FCC VERIFICATION Caution: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the e
ملخص المحتوى في الصفحة رقم 3
SAFETY PRECAUTIONS EXPLANATION OF SYMBOLS This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance. This symbol is intended to alert the user to the presence of unprotected “dangerous voltage” within the product’s enclosure that may be strong enough to cause a risk of electric shock persons. CAUTIONS THIS PRODUCT HAS MULTIPLE-RATED VOLTAGES (
ملخص المحتوى في الصفحة رقم 4
WARNINGS The product should be installed by a trained professional. The DVR should be powered off when connecting camera, audio, or sensor cables. The manufacturer is not responsible for any damages caused by improper use of the product or failure to follow instructions for the product. The manufacturer is not responsible for any problems caused by or resulting from the user physically opening the DVR for examination or attempting to fix the unit. The manufacturer may not be held l
ملخص المحتوى في الصفحة رقم 5
RACK MOUNT INSTRUCTIONS The following or similar rack-mount instructions are included with the installation instructions: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. B) Reduced Air
ملخص المحتوى في الصفحة رقم 6
CONTENTS OF DVR PACKAGE The package contains the main unit and its components as specified below. When you purchase the unit, please check to ensure the components specified below are included. DVR Set Client Software CD Remote Controller & Battery1.5V (AAA x 2EA) Adaptor (12V, 5A) & Power Cord (110V or 220V) User Guide HDD & CDRW Screw (8EA) HDD & CDRW Bracket Screw (8EA) Rack Mount (2EA)-(Option) & Rack Mount Screw (6EA)-(Option) IDE HDD Cable 80pin (1EA) ID
ملخص المحتوى في الصفحة رقم 7
VIDEO SIGNAL SELECT / SETTING Video mode Video output SETTING NTSC PAL BNC VGA O X O X Factory Default X O O X O X X O X O X O NOTICE Do not change the setting when the power is on. When the position of the switch is changed, the DVR should be rebooted to apply the new setting. 7
ملخص المحتوى في الصفحة رقم 8
COMPATIBLE HDD MODELS COMPANY MODEL SIZE RPM BUFFER INTERFACE HDS728080PLAT20 80 GB 7200 RPM 2 M E-IDE HDS721680PLAT80 82 GB 7200 RPM 8 M E-IDE HDT722516DLAT80 160 GB 7200 RPM 8 M E-IDE HDT722516DLAT80 164 GB 7200 RPM 8 M E-IDE HITACHI HDS722525VLAT80 250 GB 7200 RPM 8 M E-IDE HDT722525DLAT80 250 GB 7200 RPM 8 M E-IDE HDT725025VLAT80 250 GB 7200 RPM 8 M E-IDE HDT725032VLAT80 320 GB 7200 RPM 8 M E-IDE HDS725050KLAT80 500 GB 7200 RPM 8 M E-IDE MAXTOR 6L300R0 300 GB 7200 RPM 16 M E-IDE
ملخص المحتوى في الصفحة رقم 9
CDRW INSTALLATION GUIDE 1. Open the top cover of DVR set and Install the CDRW inside the DVR. 2. Fasten the screws on both side of CDRW as indicated in red circle below. 3. Connect the IDE CDRW 40pin cable and Power cable to the point on both CDRW and Main board as indicated in red circle below. 4. CDRW JUMPER SETTING : MASTER 9
ملخص المحتوى في الصفحة رقم 10
HDD INSTALLATION GUIDE 1. Unfasten the cover of the unit. 2. Fix the bracket to the hard disk using the supplied HDD mounting bracket screws. 3. Connect the supplied IDE HDD 80pin cable and Power cable to the hard disk and fix the hard disk to the unit the supplied HDD fixing screws. 4. HDD Jumper must set as MASTER 10
ملخص المحتوى في الصفحة رقم 11
SPECIFICATION VIDEO INPUT 4 Composite BNC (NTSC/PAL) – 1.0Vp-p OUTPUT (Selectable) 1 Composite BNC (NTSC/PAL) – 1.0Vp-p 1 VGA (D-sub 15 pin) AUDIO INPUT & OUTPUT 4 Line In (RCA) & 1 Line Out (RCA) ALARM INPUT & OUTPUT 4 & 1 OS RTOS RECORD COMPRESSION MPEG-4 VIDEO FORMAT NTSC PAL RESOLUTION 352x240, 704x480 352x288, 704x576 RECORDING MAX. 120fps/4CH(352x240/CH) MAX. 100fps/4CH(352x288/CH) QUALITY MAX. 30fps/4CH(704X480/CH) MAX. 25fps/4CH(704X576/CH) MODE By Manual, Motion, Sensor
ملخص المحتوى في الصفحة رقم 12
TABLE OF CONTENTS 1. FRONT PANEL AND REMOTE CONTROLLER........................................................... 15 1-1. Front Panel...............................................................................................................................................15 1-2. Remote controller....................................................................................................................................17 2. REAR PANEL AND CONNECTIONS...............................
ملخص المحتوى في الصفحة رقم 13
4. LIVE & SEARCH ........................................................................................................... 41 4-1. LIVE Screen..............................................................................................................................................41 4-2. SEARCH screen.......................................................................................................................................42 4-2-1. TIME LINE Search.............................
ملخص المحتوى في الصفحة رقم 14
7-6-1. General...............................................................................................................................................62 7-6-2. Site......................................................................................................................................................63 7-6-3. Event...................................................................................................................................................63 7-6-4. Reco
ملخص المحتوى في الصفحة رقم 15
1. Front Panel and Remote controller 1-1. Front Panel The following information will help you operate the front panel controls. Figure 1.1 Front panel Table1.1. Indication lamps Name Description LED light is on when the system is accessing the hard disk. HDD LED light is on when the system is recording video data. RECORD LED light is on when alarm sensor(s) is/are triggered or motion is detected. ALARM LED light is on when client is connected to the system through the network
ملخص المحتوى في الصفحة رقم 16
playback mode. Press to rewind the footage at 1x, 2x, 4x, and 8x speed in playback mode. Press to select audio mode such as SINGLE, MIX and MUTE. MUTE- All of 4 channels. SINGLE- Highlighted channel only. MIX- All of 4 channels. Jump/Step backward. In playback mode, the playback position moves 60 seconds backward. Press to enable/disable ALARM operation. Jump/Step forward. In playback mode, the playback position moves 60 seconds forward. Press to fast forward the footage at 1x, 2x,
ملخص المحتوى في الصفحة رقم 17
1-2. Remote controller RECORD Manual recording PTZ PTZ menu screen NUMBER Channel 1 to 0, To select DVR ID SEARCH Search menu screen Sequence of Full screen view SEQUENCE SETUP Setup menu screen DIRECTION Direction or number 1 to 4 To enlarge Highlighted channel SELECT Enter ESC Esc F/REW Jump 60 seconds backward PLAY/PAUSE Play/Pause F/ADV Jump 60 seconds forward ARCHIVE Archive data Rewind REW FF Fast Forward 17
ملخص المحتوى في الصفحة رقم 18
2. Rear Panel and Connections Figure 2.1. Rear Panel Table 2.1. Rear panel connections Connection DESCRIPTION Four connectors for video input. Connect camera output to Video-in (NTSC/PAL) VIDEO IN Four connectors for audio input. AUDIO IN One connector for audio output. AUDIO OUT Composite video output in NTSC or PAL format VIDEO OUT For engineering use only RS-232 Connector for VGA monitor VGA RJ45 connector for LAN connection ETHERNET For camera control use
ملخص المحتوى في الصفحة رقم 19
Figure 2.2. Rear Panel Connections 1 2 3 4OUT SENSOR ALARM Sensor (-) (-) Dried Contact +12VDC (+) (+) Adapter Figure 2.3. Sensor input / Alarm output connections SENSOR INPUT: Connect two signal lines of sensor (infrared rays sensor, heat perception sensor, magnetic sensor) to the desired sensor number. (You can set the type-NC or NO- of sensor at “Setup” mode). ALARM OUTPUT: Use this at 30V/300mA or less operating voltage and current. When controlling lamp a
ملخص المحتوى في الصفحة رقم 20
3. Setting up the DVR The following sections detail the initial setup of the DVR 3-1. SETUP - Main Screen When you press the SETUP button, the DVR will ask for a password (Figure 3.1.1). The default password is 1111, which can be entered by pressing the up button ( ) 4 times and then pressing the SEL button. We recommend you protect the system by assigning a new password immediately. The procedure for assigning a password is found in section 3.4 SYSTEM. After a password has been
