ملخص المحتوى في الصفحة رقم 1
INSTRUCTIONS
Thank you for purchasing this JVC Monitor.
Before using the monitor, read this manual carefully so
Model
that you know how to use the Monitor correctly.
Refer to this manual whenever questions or problems
GD-V4200PZW
about operation arise. Be sure to read and observe the
safety precautions.
GD-V4200PZW-G
Keep this manual where the user can see it easily.
GD-V4200PCE * Installation and removal require special expertise.
Consult your product dealer for details.
GD-V4200PCE-G
This inst
ملخص المحتوى في الصفحة رقم 2
Safety Precautions FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
ملخص المحتوى في الصفحة رقم 3
– Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.) For proper ventilation, separate
ملخص المحتوى في الصفحة رقم 4
Parts Identification Remote Control 17 8 DISPLAY ASPECT POWER 9 2 VIDEO A VIDEO B COMPO. RGB 3 MUTING VOLUME p 4 MULTIPLE MONITOR ADJUSTMENT MODE ID SET ID 5 q MENU/EXIT 6 RM-C575 REMOTE CONTROL UNIT 1 Remote signal transmission window 6 MENU/EXIT button Use this button to display or erase menus. 2 DISPLAY button (page 12) While a sub-menu is displayed, pressing this button will Use this button to display the input terminal, color system move you one screen back to the preceding menu. (for VIDEO
ملخص المحتوى في الصفحة رقم 5
Monitor: Front View 1 2 MENU INPUT POWER MENU INPUT POWER Bottom View 345 6 1 Remote sensor/power lamp 6 POWER button (page 12) Point the front end of the wireless remote control toward Use this button to turn on and off the Monitor. here. When the Monitor is turned on, the power lamp glows green. It glows red in standby mode. 2 Self-diagnostic lamps (page 29) These lamps light/flash if something abnormal occurs with the Monitor. 32 / 3 / 5 / ° buttons Use these buttons to select menu items and
ملخص المحتوى في الصفحة رقم 6
Parts Identification (Continued) Monitor: Rear View 12 3 RS232C CONTROL AC INPUT I MAIN POWER (120/230V) IN SPEAKER OUT WIRED (MULTIPLE MONITOR ADJUSTMENT) OUT REMOTE CONTROL RL INTERNAL EXTERNAL 45 6 VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO AUDIO PC L/MONO Y GD-V4200PZW and GD-V4200PZW-G Y/C Y/C PB / IN only B-Y R IN R R R RGB L/MONO L/MONO L/MONO OUT PR / OUT R-Y VIDEO A VIDEO B COMPONENT 78 9 p 6 04-11.GD-V4200PZW-A[EN]/f 6 00.2.23, 5:22 PM
ملخص المحتوى في الصفحة رقم 7
1 RS-232C CONTROL Input terminal (D-sub, 9-pin) 8 VIDEO B terminals (page 11)* (page 11) • Y/C (S video) input terminal (Y/C terminal) Connect this terminal to the RS-232C terminal of a Connect this terminal to the S-video output terminal of a personal computer. VCR, etc. • For the control method using this terminal, consult an • Video input terminal (BNC) authorized JVC dealer. Connect this terminal to the video output terminal of a VCR, etc. You can also use it as a video output terminal. 2 AC
ملخص المحتوى في الصفحة رقم 8
Preparations Checking the Accessories The following accessories are included with the Monitor. Check for them. If any item is missing, please contact the dealer where you purchased the Monitor. • Remote control (RM-C575) x 1 • Remote control cable x 1 • Power cord (approx. 2.5 m) x 3 (Use the one matching the wall outlet.) • Batteries (AA/R6P) x 2 Installing the Batteries Put the batteries in the remote control as follows. If the remote control has become erratic in operation, change the batteri
ملخص المحتوى في الصفحة رقم 9
Installation Precautions • When mounting the Monitor vertically, it is necessary to adjust the cooling fan speed to provide better heat dissipation. Do not forget to perform this adjustment. (See page 23.) • When installing the Monitor, be sure to use a dedicated Stand Unit, Wall Mounting Unit, or Monitor Hanger Unit, depending on a particular case. Ask your dealer for installation. • When installing the Monitor, refer also to the user manual for each option to use. Do not tilt the Monitor right
ملخص المحتوى في الصفحة رقم 10
Connections Precautions • Before making connections, turn off all the equipment. • Plugs should be firmly inserted; poor connection could cause noise. • To unplug a cord, be sure to grasp its plug and pull it out. • Connect the power cord after having finished all other connections. • Refer also to the user manual of each piece of equipment. Available Signals Video signals The following signals can be input to this Monitor: • VIDEO A and VIDEO B terminals accept — PAL, NTSC, and SECAM signals. •
ملخص المحتوى في الصفحة رقم 11
DISPLAY ASPECT POWER VIDEO A VIDEO B COMPO. RGB MUTING VOLUME MULTIPLE MONITOR ADJUSTMENT MODE ID SET ID MENU/EXIT RM-C575 REMOTE CONTROL UNIT Connection Examples Personal computer (used as the playback source) VCR To audio output terminals To video To S-video To monitor To audio output output output output terminals terminal terminal terminal VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO AUDIO PC Y L/MONO These terminals are not Y/C Y/C PB / IN available for B-Y R IN GD-V4200PCE and R R R RGB L/MONO L/M
ملخص المحتوى في الصفحة رقم 12
Basic Operations Daily Operations Rear View 1 Turn on the main power. Set MAIN POWER on the back of the Monitor to ON. The POWER lamp on the upper left of the front panel glows red. 2 Turn on the power. Press POWER on the remote control to turn the power on. The POWER lamp changes to glow green. 3 Select an input. Select the desired input by pressing VIDEO A, VIDEO B, COMPO. or RGB. • Only for GD-V4200PCE and GD-V4200PCE-G: Only RGB image is reproduced though you can select the 1 I MAIN POW
ملخص المحتوى في الصفحة رقم 13
Changing the Aspect Ratio With this Monitor, you can select among three types of wide screens (FULL, ZOOM, and PANORAMIC) in addition to the REGULAR screen of conventional 4:3 aspect ratio. Press ASPECT to select the screen size Each time you press the button, the screen size changes as ASPECT follows: DISPLAY ASPECT POWER REGULAR FULL VIDEO A VIDEO B COMPO. RGB PANORAMIC ZOOM MUTING VOLUME REGULAR: Displays at conventional 4:3 aspect ratio. MULTIPLE MONITOR ADJUSTMENT MODE ID SET ID MENU/EXIT F
ملخص المحتوى في الصفحة رقم 14
Video Adjustments For video adjustments, use menus. You can use the buttons either on the remote control or on Monitor for menu operations. • Refer also to “Menu Classifications” on pages 26 and 27. Adjusting the Screen Size and Position (For RGB input only) While RGB input is selected, the screen size and position can be adjusted. MENU INPUT POWER Adjusted settings can be stored for each signal type; therefore, when the same signal comes in, the stored settings are recalled. • When adjusting th
ملخص المحتوى في الصفحة رقم 15
Adjusting the Picture Quality 5 Press 2/3 to adjust the selected item. Picture quality can be set for each input mode. 6 Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu 1 Press MENU/EXIT (or MENU on the operations. Monitor) to display the Main Menu. MAIN MENU SIZE/POSITION ADJ. Cursor (3) This item PICTURE ADJ. To make an adjustment while viewing the adjustment FUNCTION SELECT STATUS DISPLAY appears only bar when the After step 3 on page 14, proceed as follows: “RGB” inp
ملخص المحتوى في الصفحة رقم 16
Video Adjustments (Continued) To make an adjustment while viewing the adjustment bar After step 3 on page 15, proceed as follows: 1 Press 5/° to move the cursor (3) to “sub menu.” 2 Press 3 to display the Sub Menu. The Sub Menu for CONTRAST appears on the screen. CONTRAST :+01 + – 3 Press 5/° to select the Sub Menu you want to adjust. MENU INPUT POWER Each time you press the button, the Sub Menu changes as follows: CONTRAST BRIGHT CHROMA MENU INPUT POWER SHARPNESS PHASE 4 Press 2/3 to adjust the
ملخص المحتوى في الصفحة رقم 17
4 Press 5/° to move the cursor (3) to 4 Press 5/° to move the cursor (3) to “COLOR TEMP.” the item you want to adjust. 5 Press 2/3 to make an adjustment. 5 Press 2/3 to adjust the selected item. Each time you press the button, the color temperature alternate between “HIGH” and “LOW.” 6 Repeat steps 4 and 5 to adjust the HIGH: To make the screen become bluish. other items. LOW: To make the screen become reddish. 7 Press MENU/EXIT (or MENU on the 6 Press MENU/EXIT (or MENU on the Monitor) twice to
ملخص المحتوى في الصفحة رقم 18
Video Adjustments (Continued) Changing the Aspect Ratio The setting adjusted applies to all inputs. • You can change the aspect ratio by pressing ASPECT. (See page 13.) 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU MENU INPUT POWER SIZE/POSITION ADJ. Cursor (3) This item PICTURE ADJ. FUNCTION SELECT appears only STATUS DISPLAY when the “RGB” input is ENTER: SELECT: EXIT: MENU selected. MENU INPUT POWER 2 Press 5/° to move the cursor (3) to “FUNCTION SELECT.”
ملخص المحتوى في الصفحة رقم 19
Setting the Receivable Signal Types Resetting the Function Selection Menu Settings You can set the receivable signal types. Normally, select You can reset all the following Function Selection Menu “AUTO.” settings at a time. A common setting will apply to both VIDEO A and B • Colour Temperature (see page 16) terminals, and a different setting will apply to the • Aspect Ratio (see page 18) COMPONENT terminal. • Receivable Signal Types: SIGNAL MODE (see the left column) 1 Press MENU/EXIT (or MENU
ملخص المحتوى في الصفحة رقم 20
Other Convenient Functions To set the other convenient functions, use menus. You can use the buttons either on the remote control or on Monitor for menu operations. • Refer also to “Menu Classifications” on pages 26 and 27. Showing On-screen Display The input mode and signal type will be indicated on the screen. • The following procedure can be done by using the buttons MENU INPUT POWER on the Monitor. You can also show these information by pressing DISPLAY on the remote control. (See page 12.)
