ATD Tools ADT-5921 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

ATD-5921
RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START
OWNERS MANUAL
• 1000 PEAK AMPS/400 CRANKING AMPS OF STARTING POWER.
• STARTS CARS, TRUCKS, RV’s AND BOATS WITHOUT THE NEED OF ANOTHER VEHICLE OR AC POWER CORDS.
• 12V DC SOCKET WITH OVERLOAD PROTECTION PROVIDES POWER FOR ANY 12V APPLIANCE.
• PROVIDES UP TO 50-HOURS OF DC POWER WHEN USED WITH 12V DC APPLIANCES.
• ALLOWS 12V DC APPLIANCES TO BE USED IN REMOTE SITES AND/OR IN EMERGENCIES WHEN COMMERCIAL POWER IS NOT AVAILABLE.
• S

ملخص المحتوى في الصفحة رقم 2

INTRODUCTION YOUR POWER PACK UNIT IS DESIGNED AS A COMPACT, DURABLE AND PORTABLE JUMP START SYSTEM FOR 12 VOLT DC VEHICLES AND BOATS. THIS SELF-CONTAINED SYSTEM WILL START MOST VEHICLES AND BOATS WITHOUT THE NEED FOR A HOST VEHICLE OR 120V AC POWER SUPPLY. THIS SYSTEM CAN ALSO BE USED AS A SAFE, PORTABLE SOURCE OF 12V DC ELECTRIC POWER IN REMOTE LOCATIONS AND/OR IN EMERGENCIES. THE POWER PACK UNIT HAS AN EASY-TO-READ, COLOR-CODED BATTERY METER THAT INDICATES CHARGE LEVEL. A 12V DC SOC

ملخص المحتوى في الصفحة رقم 3

WARNINGS • ALWAYS WEAR EYE PROTECTION WHEN WORKING ON OR AROUND LEAD-ACID BATTERIES. IF SPLASHED WITH BATTERY ACID: IMMEDIATELY FLUSH AFFECTED AREA SUCH AS FACE AND PARTICULARLY THE EYES WITH CLEAN WATER. CONTINUE FLUSHING FACE AND EYES UNTIL MEDICAL HELP ARRIVES. • LEAD-ACID BATTERIES GENERATE HYDROGEN GAS DURING NORMAL OPERATION. MORE GAS IS GENERATED WHEN THE BATTERY IS CHARGING. HYDROGEN GAS IS: 1. EXPLOSIVE 2. POISONOUS TO BREATH 3. HIGHLY FLAMMABLE • TO AVOID POSSIBLE DAMAGE THAT

ملخص المحتوى في الصفحة رقم 4

120V AC CHARGING : PLUG THE 120V AC POWER CORD INTO AN OUTLET AND INTO THE RECEPTACLE ON YOUR NEW POWER PACK UNIT. CHARGE THIS DEVICE FOR AT LEAST 4 HOURS OR UNTIL THE METER SHOWS A FULL (14- TO 15-V DC) CHARGE WHEN THE RED ROCKER SWITCH IS DEPRESSED. THE RECHARGING CONVERTER CIRCUIT IN YOUR POWER PACK UNIT HAS AN AUTOMATIC CUT-OFF CIRCUIT SO THE INTERNAL BATTERY CANNOT BE OVERCHARGED. TO RECHARGE YOUR POWER PACK UNIT BATTERY FROM 120V AC FOLLOW THESE STEPS : 1. ON THE POWER PACK UNITS' R

ملخص المحتوى في الصفحة رقم 5

TABLE III. WILL GIVE YOU AN IDEA OF WHAT OPERATION TIME YOU CAN EXPECT WHEN STARTING FROM A FULLY CHARGED SYSTEM. TABLE III.  POWER PACK UNIT AS A 12V DC POWER SOURCE  ESTIMATED  ESTIMATED  POWER  USAGE  CONSUMPTION  TIME (IN  APPLIANCE TYPE   (IN WATTS)  HOURS)  FLUORESCENT LIGHTS, CELL PHONES  4  30  RADIOS, FANS, DEPTH FINDERS  9  21  CAMCORDERS, VCR'S, SPOTLIGHTS  15  12  ELECTRIC TOOLS, BILGE PUMPS  24  7  ELECTRIC COOLERS  48  3  AIR COMPRESSORS, CAR VACUUMS  80  1.5  TABLE IV WILL G

ملخص المحتوى في الصفحة رقم 6

BATTERY REPLACEMENT FIGURE 3. - REAR VIEW OF THE POWER PACK UNIT SHOWING THE BATTERY COMPARTMENT 1. UNSCREW AND REMOVE THE EIGHT (8) PHILLIPS HEAD SCREWS THAT HOLD THE REAR COVER IN PLACE ON THE BACK OF YOUR POWER PACK UNIT. 2. LIFT OFF THE COVER PLATE TO EXPOSE THE BATTERY COMPARTMENT. 3. LIFT THE BATTERY OUT OF THE BATTERY COMPARTMENT. 4. DETACH THE #4 JUMPER CABLES AND THE RED AND BLACK RECHARGING WIRES FROM THE BATTERY TERMINALS . 5. ENSURE THAT THE REPLACEMENT BATTERY IS ORIENTED WITH

ملخص المحتوى في الصفحة رقم 7

ATD-5921 22 21 20 19 18 17 16 15 14 13 12 23 24 11 10 9 8 1 2 3 4 5 6 7