ملخص المحتوى في الصفحة رقم 1
233V5
www.philips.com/welcome
EN User manual 1
Customer care and warranty 28
Troubleshooting & FAQs 33
ملخص المحتوى في الصفحة رقم 2
Table of Contents 1. Important ................................................1 1.1 Safety precautions and maintenance ...1 1.2 Notational Descriptions .............................2 1.3 Disposal of product and packing material ................................................................3 2. Setting up the monitor .........................4 2.1 Installation ...........................................................4 2.2 Operating the monitor ...............................6 2.3 Remove Bas
ملخص المحتوى في الصفحة رقم 3
1. Important • Please use approved power cord provided 1. Important by Philips all the time. If your power cord is missing, please contact with your local This electronic user’s guide is intended for service center. (Please refer to Customer anyone who uses the Philips monitor. Take time Care Consumer Information Center) to read this user manual before you use your • Do not subject the monitor to severe monitor. It contains important information and vibration or high impact conditions
ملخص المحتوى في الصفحة رقم 4
1. Important • Temperature: 0-40°C 32-95°F what procedure to take when the operating instructions given in this manual have been • Humidity: 20-80% RH followed. Important information for Burn-in/Ghost image 1.2 Notational Descriptions • Always activate a moving screen saver program when you leave your monitor The following subsections describe notational unattended. Always activate a periodic conventions used in this document. screen refresh application if your monitor will display u
ملخص المحتوى في الصفحة رقم 5
1. Important Taking back/Recycling Information for 1.3 Disposal of product and packing Customers material Philips establishes technically and economically Waste Electrical and Electronic Equipment- viable objectives to optimize the environmental WEEE performance of the organization's product, service and activities. From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled. At Philips, end-of-life management primaril
ملخص المحتوى في الصفحة رقم 6
2. Setting up the monitor Install base stand 2. Setting up the monitor 1. Place the monitor face down on soft and smooth surface taking care to avoid scratching or damaging the screen. 2.1 Installation 2. Attach/Slide the base column with the Package contents monitor until it clicks into position. Register your product and get support at 233V5 www.philips.com/welcome Quick Start 使用产品前请阅读使用说明 3. Hold the monitor base stand with both SmartControl software 保留备用 Monitor drivers hands a
ملخص المحتوى في الصفحة رقم 7
2. Setting up the monitor Connecting to your PC 233V5LHAB 233V5LSB 5 6 4 4 A C power input V GA input A C power input D VI-D input (available for selected models) V GA input Kensington anti-theft lock HDMI input Earphone output Audio input 233V5LAB Kensington anti-theft lock Connect to PC 5 1. Connect the power cord to the back of the monitor firmly. 6 2. Turn off your computer and unplug its 4 power cable. 3. Connect the monitor signal cable to the video connector on the
ملخص المحتوى في الصفحة رقم 8
2. Setting up the monitor 2.2 Operating the monitor Front view product description 233V5LAB, 233V5LHAB 5 233V5LSB 5 7 6 4 3 2 Switch monitor’s power ON and 7 6 4 3 2 OFF. Access the OSD menu. Confirm the OSD adjustment. Switch monitor’s power ON and OFF. Return to previous OSD level. Access the OSD menu. Adjust the brightness level. Confirm the OSD adjustment. Adjust the OSD menu. Return to previous OSD level. Adjust the speaker volume. Adjust the brightness level. Adjust the OSD m
ملخص المحتوى في الصفحة رقم 9
2. Setting up the monitor Description of the On Screen Display 233V5LHAB: What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display interface is shown as below: 233V5LAB: Basic and simple instruction on the control keys
ملخص المحتوى في الصفحة رقم 10
2. Setting up the monitor The OSD Menu Resolution notification Below is an overall view of the structure of This monitor is designed for optimal the On-Screen Display. You can use this as a performance at its native resolution, 1920 × reference when you want to work your way 1080 @ 60 Hz. When the monitor is powered around the different adjustments later on. on at a different resolution, an alert is displayed on screen: Use 1920 × 1080 @ 60 Hz for best Main menu Sub menu results. VGA DVI (a
ملخص المحتوى في الصفحة رقم 11
2. Setting up the monitor Note 2.3 Remove Base Stand and Base This monitor accepts a 100mm x 100mm VESA- Remove the Base Stand Compliant mounting interface. Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 100mm 1. Place the monitor face down on a smooth 100mm surface, taking care to avoid scratching or damaging the screen. Caution For use only with UL Listed Wall Mount Bracket with minimum weight/load 3.5Kg 2.
ملخص المحتوى في الصفحة رقم 12
3. Image Optimization Icon based software is ready to enhance your 3. Image Optimization experience with Philips monitors! Installation 3.1 SmartContrast • Follow the instruction and complete the installation. What is it? • You can launch after installation is A unique technology that dynamically analyzes completed. displayed content and automatically optimizes • If you want to launch later, you can either an LCD monitor's contrast ratio for maximum click the shortcut on desktop or t
ملخص المحتوى في الصفحة رقم 13
3. Image Optimization Start with Standard pane: Adjust menu: • Adjust Menu allow you to adjust Brightness, Contrast, Focus, Position and Resolution. • You can follow the instruction and do the adjustment. • Cancel prompts user if you want to cancel installation. 11
ملخص المحتوى في الصفحة رقم 14
3. Image Optimization Color menu: • Color Menu allow you to adjust RGB, Black Level, White Point, and Color Calibration. • You can follow the instruction and do the adjustment. • Refer to below table for sub-menu item base on your input. • Example for Color Calibration: 12
ملخص المحتوى في الصفحة رقم 15
3. Image Optimization 1. "Show Me" starts color calibration tutorial. Options>Preferences - Will only be active when selecting Preferences from the drop- 2. Start - starts the 6-step color calibration down Options menu. On a non-supported sequence. display capable of DDC/CI, only the Help and 3. Quick View loads the before/after images. Options tabs are available. 4. To return to Color home pane, click the Cancel button. 5. Enable color calibration - by default is on. If unchecked, does no
ملخص المحتوى في الصفحة رقم 16
3. Image Optimization at startup will not load when this box is unchecked (Disabled). • Enable transparency mode (Windows 7, Vista, XP). Default is 0% Opaque. Options>Input - Will only be active when selecting Input from the drop-down Options menu. On a non-supported display capable of DDC/CI, only the Help and Options tabs are available. All other SmartControl Lite tabs are not available. Help>User Manual - Will only be active when selecting User Manual from the drop-down Help menu.
ملخص المحتوى في الصفحة رقم 17
3. Image Optimization The task tray has five entries: • Help - Access to User Manual file: Open User Manual file using the default browser window. • Technical Support - displays the tech support page. Context Sensitive menu • Check for Update - takes the user to PDI The Context Sensitive menu is Enabled by Landing and checks the user’s version default. If Enable Context Menu has been against the most current available. checked in the Options>Preferences pane, then • About - Displa
ملخص المحتوى في الصفحة رقم 18
3. Image Optimization Note All the illustrations in this section are for reference only. SmartControl software version might be changed without notification. Please always check official Portrait website www.portrait.com/dtune/phl/enu/index to download the latest version of SmartControl software. 16
ملخص المحتوى في الصفحة رقم 19
4. Technical Specifications 4. Technical Specifications Picture/Display Monitor Panel Type TFT-LCD Backlight LED Panel Size 23" W (58.4cm) Aspect Ratio 16:9 Pixel Pitch 0.265x 0.265 mm Brightness 250 cd/m² SmartContrast 10,000,000:1 Contrast Ratio (typ.) 1000:1 Response Time (typ.) 5ms Optimum Resolution 1920 x 1080 @ 60Hz Viewing Angle 170° (H) / 160° (V) @ C/R > 10 Display Colors 16.7M Vertical Refresh Rate 56Hz - 76Hz Horizontal Frequency 30kHz - 83kHz sRGB YES Connectivity 233V5LSB, 233V5
ملخص المحتوى في الصفحة رقم 20
4. Technical Specifications Off 0.5W Power LED indicator On mode: White, Standby/Sleep mode: White (blinking) Power Supply Built-in, 100-240VAC, 50-60Hz 233V5LSB: Power 21.55 W (typ.), 22.22 W (max.) On Mode or 21.55 W (typ.), 24.23W (max.) (for Analog only model) Sleep (Standby) 0.5W Off 0.5W Power LED indicator On mode: White, Standby/Sleep mode: White (blinking) Power Supply Built-in, 100-240VAC, 50-60Hz 233V5LHAB: Power On Mode 21.02 W (typ.), 28.51 W (max.) Sleep (Standby) 0.5W Off 0.3W P
