ملخص المحتوى في الصفحة رقم 1
Instruction Sheet
Phaser® 340
®
Adding extended features to a Phaser 340 —
Upgrade Kit Z340FX
This kit provides the 16-Mbyte RAM SIMM and print engine ROM necessary to provide additional
on-board fonts and imaging capabilities to a Phaser 340 Color Printer. This kit also includes diskettes
containing PostScript screen fonts; these allow you to use the additional on-board fonts available in the
Phaser 340 Plus. The PostScript Code ROM SIMM and engine ROM replaced
ملخص المحتوى في الصفحة رقم 2
Adding extended features to a Phaser® 340 — Upgrade Kit Z340FX Important! About the printer’s IP address (Z340FX Option 1 only) Upgrading the printer’s PostScript ROM will erase the printer’s IP address from the printer’s non-volatile memory. Therefore you should print the printer’s configuration page, which lists the printer’s IP address, before upgrading the printer. 1. While the printer is idle, press the Menu button to display the Help pages
ملخص المحتوى في الصفحة رقم 3
Adding extended features to a Phaser® 340 — Upgrade Kit Z340FX 3. Slide out the main board. NV RAM
chip Printer ID
chip Main board 9100-63 3 Ethernet® PHASER 340 1
2
Service Reset Second
Feeder Service
SCSI Disk Parallel Only Smart Card
ملخص المحتوى في الصفحة رقم 4
P71 Adding extended features to a Phaser® 340 — Upgrade Kit Z340FX Installing the PostScript Code ROM SIMM (Z340FX Option 1 only) The PostScript Code ROM SIMM is only included as a part of the upgrade if you have a printer serial-numbered BBxxxx or below. Otherwise, proceed to Step 6. 4. Remove the currently installed PostScript code ROM SIMM from image processor board (connector P71) by spreading apart the hook-like metal pawls securing each end of the SIMM in its connector.
ملخص المحتوى في الصفحة رقم 5
Adding extended features to a Phaser® 340 — Upgrade Kit Z340FX Installing the 16-Mbyte SIMM 6. If a 4-Mbyte RAM SIMM is already installed in the RAM SIMM connector J20, it must be removed. You can identify a 4-Mbyte RAM SIMM by the part number 671-1561-01 or 671-3574-00 printer on its underside. To remove the RAM SIMM, carefully spread the hook-like metal pawls securing each end of the SIMM into the connector. 7. Insert the 16-Mbyte RAM SIMM (part number 671-3133-00) in c
ملخص المحتوى في الصفحة رقم 6
Adding extended features to a Phaser® 340 — Upgrade Kit Z340FX Replacing the print engine ROM 9. Locate the print engine ROM. Note Some products may use a standard ROM IC chip while others may use an adaptor circuit board. Either part type can be substituted for the other on this main board. 10. Insert the IC removal tool between the ROM (or adaptor board ROM) and the socket. GENTLY remove the old part by prying upward, being careful to not damage the main board.
ملخص المحتوى في الصفحة رقم 7
Adding extended features to a Phaser® 340 — Upgrade Kit Z340FX 14. Follow the instructions included with the font disks shipped with this upgrade to install the fonts on your computer. Setting the printer’s IP address If you replaced the PostScript code ROM SIMM — Upgrade kit Z340FX Option 01 you will have to set the printers IP address. How you set the IP address in your printer depends on a number of factors such as the protocol used by your host TCP/IP network
ملخص المحتوى في الصفحة رقم 8
